Dobinsons SE59-525K Swaybar Relocation Bracket User Manual

June 10, 2024
Dobinsons

Dobinsons SE59-525K Swaybar Relocation Bracket

Dobinsons-SE59-525K-Swaybar-Relocation-Bracket-PRODUCT

Part Number: SE59-525K

Product Information

  • Product Name: Swaybar Relocation Bracket
  • Part Number: SE59-525K
  • Fits:
    • Toyota 4Runner 2010+ (non-KDSS)
    • Toyota FJ Cruiser 2010+
    • Lexus GX460 2010+ (non-KDSS)
  • Installation Time: Approximately 0.5-1 hour
  • Installation should be done by a qualified installer and it is the installer’s responsibility to ensure correct fitment.
  • Dobinsons is not responsible for any damage incurred to the vehicle during installation.

Product Usage Instructions

  1. Remove the plastic skid plate (five bolts with a 10mm socket and the pop clip) and set aside as these will be reused.
  2. Remove the skid plate (four bolts using a 12mm socket with an extension) and set aside as these will be reused.
  3. Remove the radiator support brackets (3 bolts each using a 14mm socket).
  4. Using two square spacers at each end and one round spacer in the center hole, install the radiator support brackets as pictured. Torque to 30 lb/ft.
  5. Remove the sway bar brackets by removing the two bolts using a 14mm socket.
  6. Install the sway bar spacers using the provided M10x1.25 20mm Socket head bolts, tighten using an 8mm allen wrench/socket. Torque to 30 lb/ft. Tip: Be sure to install with the threaded holes toward the front of the vehicle.
  7. Install the OEM Sway Bar Brackets to the spacers.
    • Tip:  Fasten the front bolt first, slide on the bracket then fasten the rear bolt. Torque to 30 lb/ft.
  8. Install the skid plates by reversing steps one and two. Do not tighten with an impact wrench.

Fits

  • Toyota 4Runner 2010+ (non KDSS)
  • Toyota FJ Cruiser 2010+
  • Lexus GX460 2010+ (non KDSS)

This Product will take aproximately 0.5-1 hour to install. Dobinsons Products should be installed by a qualified installer and it is the installers responsibility to ensure correct fitment. Dobinsons is not responsible for any damage incurred to the vehicle during installation.

PARTS LIST

13mm Square Spacer QTY:4
13mm Round Spacer QTY:2
Sway Bar Spacer QTY:2
M10x1.25 20mm Hex Head QTY:4
M10x1.25 20mm Socket Head QTY:4
M10x1.25 40mm Hex Head QTY:6
M10 Flat Washer QTY: 10

Tools Required

Ratchet Wrench with Extensions

10mm, 12mm 14mm and 16mm Sockets
8mm Allen Wrench I Socket
Clip Removal tool

INSTALLATION INSTRUCTIONS

  1. Remove the plastic skid plate (five bolts with a 10mm socket and the pop clip), set aside as these will be reused. (P1.1)
  2. Remove the skid plate (four bolts using a 12 mm socket with an extension), Set aside as these will be reused. (P1.1)
  3. Remove the Radiator support brackets (3 bolts on each using 14mm socket). (P1.2)
  4. Using two square spacers at each end and one round spacer in the center hole, install the radiator support brackets as pictured. Torque to 30ft/lb. (P1.3)(P1.4)
  5. 5. Remove the sway bar brackets by removing the two bolts using a 14mm socket. (P1.5)
  6. 6. Install the sway bar spacers using the provided M10x1.25 20mm Socket head bolts, tighten using an 8mm allen wrench / socket. Torque to 30ft/lb TIP: Be sure to install with the threaded holes toward the front of the vehicle. (P1.6)
  7. Install the OEM Sway Bar Brackets to the spacers.
    • TIP: Fasten the front bolt first, slide on the bracket then fasten the rear bolt. (P1.7) Torque to 30ft/fb.
  8. Install the skid plates by reversing steps one and two. DO NOT TIGHTEN WITH IMPACT WRENCH.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Dobinsons User Manuals

Related Manuals