RYOBI RBC1226I Brush Cutter Instruction Manual

: June 10, 2024
: RYOBI

RYOBI RBC1226I Brush Cutter

RBC1226I Brush Cutter

INTRODUCTION

Important! It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.
Subject to technical modification

Safety, performance, and dependability have been given top priority in the design of your electric lawn trimmer and brushcutter.

INTENDED USE

This lawn trimmer / brushcutter is intended to be used only by adults who have read and understood the instructions and warnings in this manual and can be considered responsible for their actions. This product is only intended for use outdoors in a well ventilated area. For safety reasons, the product must be adequately controlled by using two-handed operation. The product fitted with the lawn trimmer head (and appropriate guard) is intended for cutting long grass, pulpy weed, and similar vegetation at or about ground level. When fitted with the Tri-ArcTM blade (and appropriate guard), it can also cut bushes. The cutting plane should be approximately parallel to the ground surface. The product should not be used to cut or trim hedges, bushes, or other vegetation where the cutting plane is not parallel to the ground surface.

WARNING
When using the product, the safety rules must be followed. For your own safety and that of bystanders, please read these instructions before operating the product. Please keep the instructions safe for later use.

WARNING
The product is not intended to be used by children or persons with reduced physical, mental or sensory capabilities. Children should be supervised to ensure that they do not play with the appliance.

TRAINING

Never allow children or people unfamiliar with the instructions to use the product.
Local regulations may restrict the age of the operator.
Read the instruction carefully. Be familiar with all controls and the proper use of the product.
Keep the area clear of all bystanders, children and pets while trimming. Stop machine if anyone enters the area.
Never operate the product when you are tired, ill or under the influence of alcohol, drugs, or medicine.
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property

ELECTRICAL SAFETY

Power plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid unintentional starting. Always check that the switch is in Off position before plugging in the tool to the power supply.
Do not carry a plugged-in product with your finger on the switch.
Avoid body contact with earthed or grounded surface, such as pipes, radiator, ranges and refrigerators. There is an increased risk of electric shock is your body is earthed or grounded.
Do not operate the product when there is a risk of lightning.
Do not expose the product to rain or wet conditions. Water entering an appliance will increase the risk of electric shock.
Electrical power should be supplied via a residual current device (RCD) with a tripping current of not more than 30 mA.
Before every use, examine the power cord for damage. If there are signs of damage ,it must be replaced. Always uncoil the power cord during use. Coiled cables can overheat.
If you need to use an extension cable, ensure it is suitable for outdoor use and has a current capacity sufficient to supply your product.
The extension cord cable should be marked with either “H05 RNF” or H05 VV-F”. Check it before every use for damage. Always uncoil it during use because coiled cables can overheat.
Damaged extension cables should not be repaired; they should be replaced with an equivalent type.
Do not use the product if the electric cables are damaged or worn.
If the power cord or extension cable becomes damaged during use, disconnect from the power supply immediately. Do not touch the electric cables until the power supply has been disconnected.
Make sure the power cord is positioned so that it cannot be damaged by the cutting means and will not be stepped on, tripped over or otherwise subjected to damage or stress.
Never pick up or carry the product by the power cord.
Never pull by the power cord to disconnect from the power supply.
Keep the power cord away from heat, oil and sharp edges.
Make sure the voltage is correct for the product. A nameplate on the product indicates the product’s voltage. Never connect the product to an AC voltage that differs from this voltage.
Make sure the switch is in Off position before disconnecting from power supply

PREPARATION

Wear full eye and hearing protection while operating the product. If working in an area where there is a risk of falling objects, head protection must be worn.
Hearing protection may restrict the operator’s ability to hear warning sounds.
Pay particular attention to potential hazards around and inside the working area.
Wear heavy long trousers, boots, and gloves. Do not wear loose fitting clothing, short trousers, jewellery of any kind, or use with bare feet.
Secure long hair so it is above shoulder level to prevent entanglement in moving parts.
Before use and after any impact, check that there are no damaged parts. A defective switch or any part that is damaged or worn should be properly repaired or replaced by an authorised service facility.
Make sure the cutting attachment is properly installed and securely fastened.
Never operate the product unless all guards, deflectors and handles are properly and securely attached.
Consider the environment in which you are working. Keep the working area free from wires, sticks, stones and debris, which if struck by the cutter, can become thrown objects.

GENERAL SAFETY WARNINGS

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool’’ in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

PERSONAL SAFETY

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards

POWER TOOL USE AND CARE

Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc, in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

SERVICE

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

WARNING
Never use cutting means or attachments which are not specified by Ryobi in this manual. This includes the use of metal multi-piece pivoting chains and flail blades.
These items are known to break up during use and present a high risk of serious injury to the operator or bystanders.

WARNING
Inspection after dropping or other impacts:
Thoroughly inspect the product and identify any problems or damage to it. Any par that is damaged should be properly repaired or replaced by an authorised service centre.

LAWN TRIMMER SAFETY WARNINGS

Some regions have regulations that restrict the use of the product. Check with your local authority for advice.
Never allow children or people unfamiliar with the instructions to use the product.
Use the product in daylight or good artificial light.
Avoid using on wet grass.
Do not walk backwards when using the product.
Keep firm footing and balance. Do not overreach. Overreaching can result in loss of balance. Always be sure of your footing on slopes. Walk, never run.
Keep bystanders, children and pets 15 m away from the area of operation, stop the product if anyone enters the area.
Keep the cutting attachment below waist level.
Never operate the product with damaged guards or without guards in place.
Never fit a metal replacement line.
Keep hands and feet away from the cutting means at all times, especially when switching on the motor.
Beware, the cutting elements continue to rotate after the motor is switched off.
Beware of objects thrown by the cutting means. Clear debris like small stones, gravel and other foreign objects from the work area before starting operation. Wires or string may become entangled with the cutting means.
Switch off and disconnect from the power supply before:
- servicing
- leaving the product unattended
- cleaning your product or clearing a blockage
- changing accessories
- checking for any damage after hitting an object
- checking for any damage if the product starts to vibrate abnormally
- performing maintenance
- removing blade
- installing blade
The small blade fitted to the lawn guard is designed to trim the new extended line to the correct length for safe and optimum performance. It is very sharp; do not touch it, particularly when cleaning the product.
Always ensure that ventilation openings are kept clear of debris.
Make sure the cutting head attachment is properly installed and securely fastened.
Make sure all guards, deflectors and handles are properly and securely attached.
Do not modify the product in any way. This may increase the risk of injury to yourself or others.
Use only the manufacturer’s replacement cutting line. Do not use any other cutting attachment.
Immediately switch off and disconnect from the mains in the event of accident or breakdown. Don’t operate the product again until it has been fully checked by an authorised service centre.

BRUSHCUTTER SAFETY WARNINGS

In addition to the above rules, these additional instructions are appropriate when using the product in brushcutter mode.
Use heavy-duty gloves while installing or removing blades, they have sharp edges.
Do not attempt to touch or stop the blade when it is rotating.
A moving blade can cause severe injury. Maintain proper control of the machine with both hands until the blade has completely stopped rotating.
Replace any blade that has been damaged. Always make sure blade is installed correctly and securely fastened before each use.
Use only the manufacturer’s replacement Tri-Arc blade. Do not use any other cutting attachment.
Never cut any material over 13 mm diameter.
Your brush cutter is fitted with a harness. Carefully adjust the harness to fit comfortably and help to support the weight of the machine at your right side.
Identify the Quick Release mechanism and practice using it before you start using the product. Its correct use may prevent serious injury in case of an emergency. Never wear additional clothing over the harness or otherwise that restrict access to the quick release mechanism.
Cover the blade with the blade protector before storing the unit, or during transportation. Always remove the blade protector before using the unit. If not removed, the blade protector could become a thrown object as the blade begins to turn.
Exercise extreme caution when using the blade with this product. Blade thrust is the reaction that may occur when the spinning blade contacts anything it cannot cut. This contact may cause the blade to stop for an instant, and suddenly “thrust” the unit away from the object that was hit. This reaction can be violent enough to cause the operator to lose control of the unit. Blade thrust may occur without warning if the blade snags, stalls, or binds. This is more likely to occur in areas where it is difficult to see the material being cut.
For cutting ease and safety, approach the weeds being cut from the right to the left. In the event that an unexpected object or woody stock is encountered, this practice could minimize the blade thrust reaction. Both hands must be used at all times to control this product.

TRANSPORTATION AND STORAGE

Stop the product and allow it to cool before storing or transporting.
Clean all foreign materials from the product.
If a cutting blade is fitted, cover it with the blade protector.
If a cutting blade is fitted, cover it with the blade protector.
For storage, always disconnect from power supply and wind the cable. Store it in a cool, dry and well-ventilated place that is inaccessible to children. Keep away from corrosive agents, such as garden chemicals and de-icing salts. Do not store outdoors.
For transportation, secure the product against movement or falling to prevent injury to persons or damage to the product.

MAINTENANCE

WARNING
Use only original manufacturer’s replacement parts, accessories, and attachments. Failure to do so can cause possible injury, poor performance, and may void your warranty.

WARNING
Servicing requires extreme care and knowledge and should be performed only be a qualified service technician. For service, we suggest you bring the product to your nearest authorised service centre for repair. When servicing, use only identical replacement parts.

Switch off and disconnect from the mains before conducting any maintenance or cleaning work.
You may make adjustments and repairs described here. For other repairs, contact the authorised service agent.
For the replacement line, use only nylon filament line of the diameter described in the specification table of this manual.
After extending the new cutter line, always return the product to its normal operating position before starting.
After each use, clean the product with a soft dry cloth. Any part that is damaged should be properly repaired or replaced by an authorised service centre.
Check all nuts, bolts, and screws at frequent intervals for proper tightness to ensure the product is in a safe working condition.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:
lowing:

Injury caused by vibration.
Hold the product by designated handles and restrict working time and exposure.
Injury caused by exposure to noise Wear hearing protection and limit exposure.
Injury caused by flying debris Wear eye protection at all times.

Contact with cutting means. Ensure that the blade protectors are fitted when the machine is not in use. Keep hands and feet away from the blades at all times.

Kickback can occur when using the brush cutter. Ensure proper control by using both hands on the designated handles. Read and follow the directions elsewhere in this manual to help reduce the risk of kickback.
Risk of falling objects. During brush cutting,wear head protection if there is any risk of falling objects.

RISK REDUCTION

It has been reported that vibrations from handheld products may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness, and blanching of the fingers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking, and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:

Keep your body warm in cold weather.
When operating the product, wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
After each period of operation, exercise to increase blood circulation.
Take frequent work breaks. Limit the amount of exposure per day.

If you experience any of the symptoms of this condition, immediately discontinue use and see your doctor about these symptoms.

WARNING
Injuries may be caused or aggravated by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

KNOW YOUR PRODUCT

See page 205.

Know Your Product

Rear handle
Lock-out trigger
Trigger
Front handle
Harness
Upper shaft
Lower shaft
Blade
Blade guard
Blade protector
Cord retainer
Power cord
Grass deflector
Cut-off blade
Cutting line
Bump head
Spool cover
Spool
Eyelet

SYMBOLS ON THE PRODUCT

| Safety alert
---|---
| Read and understand all instructions before operating the product, follow all warnings and safety instructions.
| Wear eye, ear and head protection.
| Wear non-slip safety footwear when using the product.
| Wear non-slip, heavy duty gloves
| Do not expose to rain or damp conditions.
| Remove plug from the mains immediately before maintenance or if cable is damaged, cut or entangled.
| Beware of thrown or fl ying objects. Keep all bystanders a safe distance away from the product.
| Beware of thrown or fl ying objects. Keep all bystanders, especially children and pets, at least 15m away from the operating area
| Keep hands away from cut-off blade.
| Class II tool, double insulation
| Ukrainian mark of conformity
| EurAsian Conformity Mark
| Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
| Conforms to all regulatory standards in the country in the EU where the product is purchased.
| This product is not intended for use with a toothed saw type blade.
| Beware of blade thrust.
| Tri-Arc blade is appropriate for this product and is suited for cutting pulpy weeds and vines.
| Rotational direction and maximum speed of the shaft for the cutting attachment.
| Brush cutter Guaranteed sound power level is 100 db.
| Lawn trimmer Guaranteed sound power level for is 96 db.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

DANGER
Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
CAUTION
Without safety alert symbol Indicates a situation that may result in property damage.

SYMBOLS IN THIS MANUAL

| .
---|---
|
|
|

PARTS

Parts

OPERATING INSTRUCTIONS

Operating Instructions

Product specifi cations

Electric Brush cutter and Lawn Trimmer
Model
Rated power
Rated voltage
No-load speed
Brush cutter
Lawn Trimmer
Cutting line diameter
Cutting capacity
Brush cutter
Lawn Trimmer
Vibration level (in accordance with EN 50636-2-91:2014 Annex BB)
Brush cutter – Front handle – Rear handle
Lawn Trimmer – Front handle – Rear handle
Uncertainty of measurement
Noise emission level (in accordance with EN 50636-2-91:2014 Annex CC)
A-weighted sound pressure level at operator’s position
Brush cutter
Lawn Trimmer
Uncertainty of measurement
A-weighted sound power leve
Brush cutter
Uncertainty of measurement
Lawn Trimmer
Uncertainty of measurement
VDE power cord length
Weight
Brush cutter
Lawn Trimmer
UK power cord length
Replacement parts

1.5 mm complete spool
Grass defl ector
Blade
Blade guard

GUARANTEE

In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.

The guarantee period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data which are required to enter online and they have to accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty. Your statutory rights remain unaffected.
The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to
– any damage to the product that is the result of improper maintenance
– any product that has been altered or modified
– any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
– any damage caused by non-observance of the instruction manual
– any non CE product
– any product which has been attempted to be repaired by an nonqualified professional or without prior authorization by Techtronic Industries
– any product connected to improper power supply (amps, voltage, frequency)
– any product used with inappropriate fuel mixture (fuel, oil, percentage of oil)
– any damage caused by external influences (chemical, physical, shocks) or foreign substances
– normal wear and tear of spare parts
– inappropriate use, overloading of the tool
– use of non-approved accessories or parts
– carburettor after 6 months, carburettor adjustments after 6 months
– components (parts and accessories) subject to natural wear and tear, including but not limited to bump knobs, drive belts, clutch, blades of hedge trimmers or lawn mowers, harness, cable throttle, carbon brushes, power cord, tines, felt washers, hitch pins, blower fans, blower and vacuum tubes, vacuum bag and straps, guide bars, saw chains, hoses, connector fittings, spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines, spark plugs, air filters, gas filters, mulching blades, etc.
For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will have to be paid by the sender.
This guarantee is valid in the European Community, Switzerland, Iceland,
Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.

EC DECLARATION OF CONFORMITY

Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany

Herewith we declare that the product
Electric Brushcutter and Lawn Trimmer
Brand: Ryobi
Model number: RBC1226I
Serial number range: 44470801000001 – 44470801999999

is in conformity with the following European Directives and harmonized standards 2006/42/EC, 2004/108/EC (until April 19, 2016), 2014/30/EU (after April 20, 2016), 2000/14/EC, 2005/88/EC, 2011/65/EU, EN 60335-1:2012+A11:2014, EN 50636-2-91:2014, EN 60745-1:2009+A11:2010, EN ISO 11806-1:2011, EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+A1:2001+A2:2008, EN 61000-3-2:2014, EN 61000-3-3:2013, EN 50581:2012

Brushcutter:
Measured sound power level: 98.2 dB(A)
Guaranteed sound power level: 100 dB (A)
Conformity assessment method to Annex V Directive 2000/14/EC amended by 2005/88/ EC

Lawn Trimmer:
Measured sound power level: 94.87 dB(A)
Guaranteed sound power level: 96 dB (A)
Conformity assessment method to Annex VI Directive 2000/14/EC amended by 2005/88/ EC

The notified body involved:
Société Nationale de Certification et d’ Homologation (Notified Body 0499)
11, route de Luxembourg L-5230 Sandweiler

Signature