Cybernet IPC-R2IS Desktop Computer Desktop Computer User Manual
- June 10, 2024
- Cybernet
Table of Contents
IPC-R2IS Desktop Computer Desktop Computer
Product Information
The IPC-R2is and IPC-E2is are computer systems that comply with
all applicable European Union (CE) directives if it has a CE
marking. They have a CPU with Memory and Storage capabilities,
Video & Graphics support, Front I/O and Rear I/O Ports, Power
Input, Wireless Communications, Operating System, Operating
Environment, Relative Humidity, Vibration Shock, Dimensions,
Weight, System BIOS, and TPM. These systems have certifications for
FCC part 15B class B EN55032 / EN55024 class B ICES-003.
Product Usage Instructions
-
Read the safety instructions carefully before using the
equipment. -
Keep the equipment away from humidity.
-
Lay the equipment on a reliable flat surface before setting it
up. -
Confirm the voltage of the power source and adjust accordingly
to 110/220V before connecting the equipment to the power
inlet. -
Place the power cord in such a way that it cannot be stepped
on. Do not place anything over the power cord. -
Always unplug the Power Cord before inserting any add-on card
or module. -
All cautions and warnings on the equipment should be
noted. -
Never pour any liquid into the opening of the equipment. This
will cause damage and/or electrical shock. -
Do not disable the protective grounding pin from the plug. The
equipment must be connected to a grounded main socket/outlet. -
If any of the following situations arise, have the equipment
checked by a professional:-
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment. -
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the
manufacturer.
-
-
To turn on the system, press the Power Button.
-
To force a shutdown, press and hold the Power Button for
4-seconds. -
The HDMI Port supports up to 4096×2304 resolution at 60Hz.
-
There are 4x USB3.1 connections available, which supports up to
5Gbps data rate. These USB ports are also compliant with Super
Speed (SS), High Speed (HS), Full Speed (FS), and Low Speed
(LS). -
There are 2x USB2.0 connections available, which supports up to
480Mbps data rate. These USB ports are also compliant with High
Speed (HS), Full Speed (FS), and Low Speed (LS).
IPC-R2is / IPC-E2is User Manual
Declaration of Conformity
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be require to correct the interference at his own expense.
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The product(s) described in this manual complies with all applicable European Union (CE) directives if it has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE compliance also requires proper cable and cabling techniques.
Trademarks
All trademarks are the properties of their respective owners. Intel® is a
registered trademarks of Intel Corporation. PS/2 and OS®/2 are registered
trademarks of International Business Machines Corporation. Windows® 11/10 are
registered trademarks of Microsoft Corporation. Netware® is a registered
trademark of Novell, Inc. Award® is a registered trademark of Phoenix
Technologies Ltd. AMI® is a registered trademark of American Megatrends Inc
DOC ID: 16001100
Page | 1
WEEE Statement
(Waste Electrical and Electronic Equipment)
The WEEE directive places an obligation on EU-based manufacturers,
distributors, retailers and importers to take-back electronics products at the
end of their useful life. A sister Directive, ROHS (Restriction of Hazardous
Substances) compliments the WEEE Directive by banning the presence of specific
hazardous substances in the products at the design phase. The WEEE Directive
covers products imported into the EU as of August 13, 2005. EU-based
manufacturers, distributors, retailers and importers are obliged to finance
the costs of recovery from municipal collection points, reuse, and recycling
of specified percentages per the WEEE requirements.
Instructions for disposal of WEEE by Users in the European Union
The symbol shown below is on the product or on its packaging, which indicates
that this product must not be disposed of with other waste. Instead, it is the
user’s responsibility to dispose of their waste equipment by handing it over
to a designated collection point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household
waste disposal service or where you purchased the product.
DOC ID: 16001100
Page | 2
Safety Instructions
1. Always read the safety instructions carefully. 2. Keep this equipment away
from humidity. 3. Lay this equipment on a reliable flat surface before setting
it up. 4. Confirm the voltage of the power source and adjust accordingly to
110/220V
before connecting the equipment to the power inlet. 5. Place the power cord in
such a way that it cannot be stepped on. Do not
place anything over the power cord. 6. Always unplug the Power Cord before
inserting any add-on card or module. 7. All cautions and warnings on the
equipment should be noted. 8. Never pour any liquid into the opening. This
will cause damage and/or electrical
shock. 9. Do not disable the protective grounding pin from the plug. The
equipment must
be connected to a grounded main socket/outlet. 10. If any of the following
situations arise, have the equipment checked by
authorized service personnel: · The power cord or plug is damaged. · Liquid
has penetrated into the equipment. · The equipment has been exposed to
moisture. · The equipment has not worked well or you cannot get it working
according to
the User’s Guide. · The equipment has been dropped and damaged. · The
equipment has obvious signs of breakage. 11. Do not attempt to remove or
upgrade any components by yourself, any installation or modification should be
conducted by service personnel.
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONDITIONED ENVIRONMENT WITH A STORAGE
TEMPERATURE ABOVE 70° C (158°F). IT MAY DAMAGE THE EQUIPMENT.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer.
DOC ID: 16001100
Page | 3
Table of Contents
Declaration of Conformity ……………………………………………………………………………….. 1 Trademarks
…………………………………………………………………………………………………….. 1 WEEE Statement
…………………………………………………………………………………………….. 2 Safety Instructions
………………………………………………………………………………………….. 3 Introduction
……………………………………………………………………………………………………. 5 IPC R2is & IPC E2is
Specifications…………………………………………………………………… 6 IPC-R2is & IPC-E2is Overview
…………………………………………………………………………. 8
IPC-R2is Dimension ………………………………………………………………………………………. 8 IPC-E2is
Dimension……………………………………………………………………………………….. 8 IPC-R2is Front I/O View
…………………………………………………………………………………. 9 IPC-E2is Front I/O
View………………………………………………………………………………….. 9 IPC-R2is / IPC-E2is Back I/O
View…………………………………………………………………… 9 Power
Management……………………………………………………………………………………….. 16 Waking the System Up
…………………………………………………………………………………. 18 IPC-R2is / IPC-E2is BIOS introduction
……………………………………………………………. 19 Appendices ……………………………………………………………………………………………………
20 A – Cybernet’s Recycling Program………………………………………………………………….. 21 B – Getting
Help …………………………………………………………………………………………… 21
DOC ID: 16001100
Page | 4
Caution:
Warning, electricity
Direct current
Operating Instructions
Alternating current
Ready to use
Introduction
Congratulations on your purchase of the IPC-R2is / IPC-E2is. We are confident
the IPCR Series is the premier Slim Rugged PC line on the market. With their
sleek design and small form factor, these units can be quickly deployed
anywhere they are needed and their easy-to-use, feature-packed interfaces
offer an unparalelled user experience. If you have any questions about your
new IPC-R2is / IPC-E2is, please do not hesitate to contact us using any of the
support numbers provided at the end of this User Manual.
DOC ID: 16001100
Page | 5
IPC R2is & IPC E2is Specifications
CPU Memory Storage Video & Graphics
Front I/O Ports
Rear I/O Ports
Power Input Wireless Communications Operating System Operating Environment
Relative Humidity Vibration Shock Dimensions Weight System BIOS TPM
Supports Intel Whiskey Lake 8th Generation Processor, FCBGA1528 2 x DDR4 SO- DIMM sockets, up to 32GB combined Supports memory data transfer rates of 2133MHz/2400 MHz for DDR4, un-buffered non-ECC DDR4 SO-DIMMs Serial ATA controller facilitates high-speed transfers up to 6Gbps Maximum 2 x 2.5″ HDD or SSD Intel® UHD Graphics 620 2x HDMI1.4 Port, up to 4096 x 2304 @ 60Hz 4x USB3.1 2x USB2.0 2x RJ45 Gigabit (Gbe) LAN 1x COM RS-232 / 422 / 485 and 5V / 12V / RI 1x DC-IN Power Connector (6-36V) 1x DC-IN Power Terminal Block (6-36V) 1x Remote On/Off Terminal Block 3x COM RS-232 2x Easy access HDD door with lock 1x Power button 2x POE LAN support, complies with IEEE 802.3at, up to 25.5W at 52V per port (Optional) 19V / 3.78A Power Adapter, 72W, AC Input: 100-240V AC / 2.0A/ 50-60Hz 19V / 6.31A Power Adapter, 120W, AC Input: 100-240V AC 2.0A/ 50-60Hz Intel AC9260/AX200/AX210 support IEEE802.11ac/ax + BT5.1 above (Optional) Windows 11 / 10 / IoT / Pro Linux Ambient Temperature: -10°C ~ 50°C (operating) 10% ~ 95% (non-condensing) 5 Grms @5-500 Hz according to IEC60068-2-64 Operating, 50 Grms, Half-sine 11ms duration according to IEC60068-2-27 10.74″ x 6.65″ x 2.16″ (L,W,D) 5 lb AMI Flash BIOS supports ACPI, API, DMI, Plug & Play, and security password. BIOS System POST and BIOS setup password protection. TPM version 2.0 Support. 1 x Trusted Platform Module (TPM2.0) Infineon SLB9665
DOC ID: 16001100
Page | 6
Certifications
FCC part 15B class B EN55032 / EN55024 class B ICES-003
DOC ID: 16001100
Page | 7
IPC-R2is & IPC-E2is Overview IPC-R2is Dimension
IPC-E2is Dimension
DOC ID: 16001100
Page | 8
IPC-R2is Front I/O View IPC-E2is Front I/O View IPC-R2is / IPC-E2is Back I/O View
DOC ID: 16001100
Page | 9
Power button
The Power Button is a momentary switch with LED indicator.
LED Color Solid Blue
Blinking
Power Status S0 S3
System Status Working state Suspend to RAM
Press the power button to turn on the system. To force a shutdown, press and hold the power button for 4-seconds.
HDMI Port
HDMI1.4 supports up to 4096×2304 resolution at 60Hz.
USB3.1
There are 4x USB3.1 connections available, which supports up to 5Gbps data rate. These USB ports are also compliant with Super Speed (SS), High Speed (HS), Full
DOC ID: 16001100
Page | 10
Speed (FS), and Low Speed (LS).
USB2.0
There are 2x USB2.0 connections available, which supports up to 480Mbps data
rate. These USB ports are also compliant with High Speed (HS), Full Speed
(FS), and Low Speed (LS).
Ethernet Port
LAN1: Intel I219LM 10/100/Gigabit LAN, supports Wake on LAN, PXE boot and vPro
technology. LAN2: Intel I210 10/100/Gigabit LAN, supports Wake on LAN, PXE
boot and vPro technology.
DOC ID: 16001100
Page | 11
Serial Ports
Serial port 1 can be configured for RS-232, RS-422, or RS-485 with auto flow
control communication. The default definition of COM1 is RS-232, which can be
configured in the BIOS.
The pin assignments are listed below:
Serial Port
COM1
Pin No.
1 2 3 4 5 6 7 8 9
RS-232
DCD RXD TXD DTR GND DSR RTS CTS RI/5V/ 12V
RS-422 (5-wire)
TXDTXD+ RXD+ RXDGND —————————————–
RS-422 (9-wire)
TXDTXD+ RXD+ RXDGND RTSRTS+ CTS+ CTS-
RS-485 (3-wire) DATADATA+ ———————
GND —————————————–
DOC ID: 16001100
Page | 12
Serial ports 2-4 are all RS-232 and the pin assignments are listed below:
Serial Port COM2~4
Pin No.
1 2 3 4 5 6 7 8 9
RS-232
DCD RXD TXD DTR GND DSR RTS CTS NC
SSD/HDD Trays
There are 2x front-accessible 2.5″ SSD/HDD locking trays.
DOC ID: 16001100
Page | 13
Power Terminal Block
The system supports 9V to 36V DC power input by terminal block.
Pin No. 1 2 3
Definition V+ NC
Chassis Ground
Power On/Off Switch
This terminal block supports a 2-pin power on/off switch.
Pin No. 1 2 3
Definition Power
Power LED Chassis Ground
DOC ID: 16001100
Page | 14
PoE (Power over Ethernet) Ports (Optional)
There are 2x optional Ethernet ports on the IPC-R2is / IPC-E2is that supports
IEEE 802.3at (PoE+) Power over Ethernet connection, delivering up to 25.5W /
52V per port and 1000BASE-T GbE data signals over standard Ethernet Cat 5/6
cable. Each PoE connection is powered by Intel® i210 GbE Ethernet controller
and independent PCI express interface to connect with multi-core processor for
network and data transmit optimization.
DOC ID: 16001100
Page | 15
Power Management
Taking advantage of the power management options available on Windows OS can
save you significant amounts of electricity and also provide environmental
benefits. For better energy efficiency, turn off your display or set your PC
to sleep mode after prolonged periods of user inactivity.
Power Management in Windows OS
Right click the start button, and select [Power Options].
Then click [Additional power settings].
DOC ID: 16001100
Page | 16
Select a power plan that suits your personal needs. You may also fine-tune the
settings by clicking [Change plan settings].
For quick and convenient management of system power, the Shut Down Menu
provides options for Sleep (S3) and Shut Down (S5).
Power Management through ENERGY STAR qualified monitors (Not supplied with the
IPC-R2is / IPC-E2is) The power management feature allows the IPC-R2is / IPC-
E2is to initiate a low-power or “Sleep” mode after a period of user
inactivity. When used with an external ENERGY STAR qualified mnitor, this
functionality also supports similar power management features for the display.
To take advantage of these potential energy savings, the power management
feature can be set to behave in the following ways when the system is
operating on AC power:
· Turn off the display after 15 minutes.
· Initiate Sleep after 30 minutes.
DOC ID: 16001100
Page | 17
Waking the System Up
The IPC-R2is / IPC-E2is can wake up from power saving mode in response to a
command from any of the following:
· the power button, · the network (Wake on LAN) · the mouse · the keyboard
DOC ID: 16001100
Page | 18
IPC-R2is / IPC-E2is BIOS introduction
The AMI BIOS provides a Setup utility program for specifying system
configurations and settings. The BIOS ROM of the system stores the Setup
utility. When you turn on the computer, the AMI BIOS is immediately activated.
Pressing the key allows you to enter the Setup utility. If you
are a little bit late pressing the key, POST (Power On Self-
Test) will continue with its test routines, thus preventing you from invoking
the Setup. If you still wish to enter Setup, restart the system by pressing
the “Reset” button or simultaneously pressing the
DOC ID: 16001100
Page | 19
Appendices
DOC ID: 16001100
Page | 20
A – Cybernet’s Recycling Program
B – Getting Help
Corporate Headquarters
Cybernet Manufacturing 5 Holland
Irvine, California 92618 Free:
888-834-4577 Phone:
949-600-8000 Fax:
949-600-8013
www.cybernet.us sales@cybernet.us
Asia & Middle East Inquiries
Cybernet Asia Co., Ltd. 6F.-11, No. 54, Sec. 4, Minsheng E. Rd.,
Songshan Dist., Taipei City 105, Taiwan (R.O.C.)
Phone: (02) 7742-2318 Fax: (02) 2793-3172 www.cybernet.com.tw
sales@cybernet.com.tw
UK & European Inquiries
Cybernet Europe #6, Groveland Business Centre
Boundary Way Hemel Hempstead, HP2 7TE
United Kingdom Phone: +44.845.539.1200 Fax: +44.0845.539.1201
www.cyberneteurope.co.uk sales@cyberneteurope.com
Australia Support Center
Cybernet Australia, PTY Ltd. 9A/38 Bridge Street
Eltham Victoria 3095, Australia Phone: +61.3.9431.4557 au.cybernet@cybernet.us
DOC ID: 16001100
Page | 21
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>