CHAPIN 2060575 Sprayers Choice 2 gal. Plastic Tank Sprayer User Manual

CHAPIN 2060575 Sprayers Choice 2 gal. Plastic Tank Sprayer

WARNING:
Improper use or failure to follow instructions can result in explosive failure causing serious eye or another injury. For the safe use of this product, you must read and follow all instructions. Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in a possible explosion. Do not store or leave the solution in the tank after use. Always wear goggles, gloves, a long-sleeve shirt, long pants, and full foot protection when spraying. Never use any tool to remove the pump if there is pressure in the sprayer. Never stand with your face or body over top of the tank when pumping or loosening the pump to prevent ejecting pump assembly and/or solution from striking and injuring you. Never pressurize the sprayer by any means other than the original pump. Do not attempt to modify this sprayer. Replace parts only with the manufacturer’s original parts. Never spray flammable, caustic, acidic, chlorine, bleach, or other corrosive solutions or heat, pressure, or gas-producing chemicals. Always read and follow the chemical manufacturer’s instructions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.

Parts

Note: Your particular sprayer may not include all parts pictured above.

WARNING

To prevent the hose from blowing off, the hose must cover both barbs on the outlet tube adapter and touch the flange (Fig. 1B) before the hose nut is securely tightened (Fig. 1C).

Hose to Tank

Discharge/Assembly

• Insert the outlet tube into the outlet tube adapter (Fig.1A).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).
• Firmly insert the outlet tube portion into the tank adapter (Fig. 1C) leaving no gap between the tank adapter and outlet tube adapter.
• Firmly tighten the retaining nut to the tank adapter (Fig. 1C).

Nozzle/Extension Wand

Attach the nozzle to shut-off the handle or extension wand.

Filter

The filter helps prevent clogging while spraying. It is located on the end of the outlet tube inside your sprayer tank. To clean the filter, remove the discharge assembly from the tank (Fig.1A). Make sure the filter is positioned at the bottom of the tank as pictured.

Fatigue-free Spraying

For constant spraying, push down on the shut-off handle and move the gray locking mechanism away from you. To release, squeeze the handle and move the gray locking mechanism back toward you.

Note: Fatigue-free spraying lock is not supplied with all sprayers.

Shield Attachment to Wand

Snap shields onto the wand as shown. Using the spray shield will help protect your plants etc. from the spray. (Not all models are provided with a spray shield).

Pre-Use Check

1. Do: Check the tightness of the hose nut to be sure the hose is securely attached to the tank outlet.
2. Do: Inspect the hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace the hose before using it. Replace with original manufacturer’s parts only.
3. Do: Remove the pump (see Filling, Pressurizing, and Spraying Instructions), and inspect the interior and exterior of the tank for signs of deterioration of the body and bottom. Any sign of deterioration indicates possible tank weakening and could result in explosive bursting under pressure. If any of these signs are found, discard the tank immediately and replace it. Do not attempt to patch leaks, etc., as this could result in serious injury.
4. Do: Follow Filling, Pressurizing, and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and inspect for leaks).
5. Do: Direct shut-off away from you and open to making sure discharge is not clogged.
6. Do: If the unit passes this test, release pressure (see Pressure Releasing Instructions), empty the tank, and proceed with Filling, Pressurizing, and Spraying Instructions.
7. Do: Inspect all metal parts including the wand, nozzle, and fittings for rust, corrosion, and pitting. If any of these conditions are found, replace the affected part with the original manufacturer’s part before using it.

Filling

1. Do: Turn the pump handle counterclockwise and remove the pump
2. Do: Prepare spray solution following all directions and safety warnings on the chemical label.
3. Do: Fill the tank with no more than the proper gallon marker. Do NOT: overfill to accommodate the pump.
4. Do: Check the pump to make sure that no grass or dirt is stuck to the barrel. Replace the pump in the tank and tighten it securely.

Pressurizing and Spraying

• Do: Turn the handle clockwise to tighten. Push the handle down, turn 1/4 turn counterclockwise to release.
• Do: Pump until you feel resistance.
• Do: Push the handle, down, turn 1/4 turn clockwise to lock. Begin spraying. Re-pump sprayer as required to maintain spray force.

To Release Pressure

1. Your sprayer is equipped with a pressure release button. To release pressure press the red button until the air is completely exhausted.
2. Do: Point airflow away from you and others until the air has escaped.

Care, Storage, and Maintenance

1. Do: Follow the chemical manufacturer’s instructions for cleaning. Rinse thoroughly with recommended solvent.
2. Do: Open the shut-off and allow water to run through the discharge assembly. Follow Filling, Pressurizing, and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed after each use.
3. Do: Release pressure (Follow Pressure Release Instructions), remove the pump, and empty the sprayer.
4. Do: Store the sprayer tank upside down, with the pump removed, in a warm dry location.
5. Do: Periodically oil pump by dropping 10-12 drops of light oil down the pump rod through an opening in the cover.

Troubleshooting

The tank pressurizes but does not spray.

WARNING:
Release pressure in the tank before troubleshooting.

Clean shut-off (Fig. 11A- 11D)

• Pull the handle straight up.
• Insert notches from the underside of the handle into plunger grooves and turn counterclockwise.
• Remove the plunger and diaphragm. Clean plunger, diaphragm, and body. Flip the diaphragm and replace it.
• Tighten the plunger clockwise until flush with the top of the shut-off body. Do not over-tighten or the unit may not spray. Slide forks under the plunger, and push the handle down until it snaps into place.

Clean Nozzle Assembly (Fig. 11E)
Remove the nozzle cap. Clean and re-assemble.

P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.1-800-950-4458 www.chapinmfg.com.

Congratulations!
You have just purchased a quality Chapin product.

Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To the Store. Call us @ 1-800-950-4458 or www.chapinmfg.com.

References

• Chapin International
• Chapin International: Sprayers, Spreaders, Industrial, Irrigation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>