KUBE SOUND KS400 Portable Speaker User Manual
- June 10, 2024
- KUBE SOUND
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS : Please read and keep all safety and
use instructions.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Clean only with a dry cloth.
- Do not block any ventilation openings.
- Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Protect the power cord from being walked on or pinched at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, or objects have fallen into the apparatus, the apparatus does not operate normally, or has been dropped.
This symbol on the product means there is uninsulated, dangerous voltage within the product enclosure that may present a risk of electrical shock.
This symbol means there are important operating and maintenance instructions in this guide.
CAUTION: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment
WARNING: This product contains magnetic material. Consult your physician
on whether this might affect your implantable medical device.
-
Keep the product away from fire and heat sources.
-
Do NOT place naked flame sources, such as lighted candles, on or near the product.
-
Do NOT make unauthorized alterations to this product.
-
Do NOT use a power inverter with this product.
-
The speaker wire and interconnect cables included with this system are not approved for in-wall installation. Please check your local building codes for the correct type of wire and cable required for in-wall installation.
-
Where the main plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
-
Use at altitude less than 2000 meters only.
-
Due to ventilation requirements, KubeSound does not recommend placing the product in a confined space such as in a wall cavity or in an enclosed cabinet.
-
Do not place or install the product near any heat sources, such as fireplaces, radiators, heat registers or other apparatus (including amplifiers) that produce heat.
-
Danger of explosion or leakage of flammable liquid or gas if battery is incorrectly replaced. Replace only with the same or equivalent battery.
-
Disposal of a battery into a fire or hot oven, or mechanically crushing or cutting of the battery can result in an explosion.
-
Leaving a battery in an extremely high temperature environment can result in an explosion or the leakage of flammable liquid or gas.
-
Battery cannot be subjected to high or low extreme temperatures, or low air pressure at high altitude during storage or transportation.
-
A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
-
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems
-
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.
- This equipment should be installed and operated with a minimum distance of 20 cm between radiator and your body.
- The plug on the power supply cord shall connect to a socket-outlet with an earthing (grounded) connection.
QUICK START GUIDE
01 // TURN KUBE ON
Press and hold the Power button for up 5 seconds until first lights illuminate.
Wait for KUBE to start up (about 30 seconds).
Once complete, the KUBE startup sound plays and all button lights will illuminate.
02 // GET CONNECTED VIA WIFI AND UPDATE FIRMWARE
Download and open the latest KubeSync App on your device.
Short press Connect button until white to put in Wifi mode. Press and hold Connect button for 2 seconds.
The Connect LED begins to blink white/red to indicate that it is broadcasting the setup network and you will hear an audio confirmation.
When the unit connects to a Wifi network, the Connect button and LED should become solid white and you will hear an audio confirmation. The unit will remember the last Wifi network after powering off and on.
Follow the instructions on the KubeSync App to connect your Kube4 to the network.
Once connected, the App will automatically search for the latest firmware and begin installation.
03 // GET CONNECTED VIA BLUETOOTH
Short press Connect button until blue to put in Bluetooth mode. Press and hold Connect button for 2 seconds.
The Connect LED begins to blink blue/red to indicate that it is in pairing mode and you will hear an audio confirmation.
When the unit connects to a Bluetooth device, the Connect button and LED should become solid blue and you will hear an audio confirmation.
ACCESS THE FULL USER MANUAL FOR MORE FEATURES INCLUDING:
Outdoor Mesh Mode
Syncing Multiple Kube4s
Microphone Mixing
PA Mode
Documents / Resources
| KUBE
SOUND KS400 Portable
Speaker
[pdf] User Manual
2ANJG-KS400, 2ANJGKS400, ks400, KS400 Portable Speaker, KS400, Portable
Speaker, Speaker
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>