XL-3620 2D Barcode Scanner

Product Information:

The 2D Barcode Scanner is a device used for reading and decoding
barcodes. It supports USB-KBW, RS232, and USB Virtual Com data
interfaces. The scanner has a default keyboard layout of English
(United States), which can be changed to other keyboard layouts
available in the device.

The scanner has a barcode encoding configuration feature that
allows manual setup in case of peculiar characters that may affect
the output of the barcode content.

Product Usage Instructions:

1. Connect the scanner to the PC port using the dedicated joint
   and turn on the barcode configuration if it’s turned off.

2. Enable or disable the configuration barcode depending on
   whether you want to set up the scanner or not. To enable the
   configuration function, scan the “Enable Configuration Function
   (Default)” barcode. To disable it, scan the “Disable Configuration
   Function” barcode.

3. Restore the scanner to factory default configuration by
   scanning the “Restore Factory Default Configuration” barcode.

4. Scan the “Save” barcode to save the current parameters as
   user’s configuration. Scan the “Restore User Configuration” barcode
   to restore a saved user’s configuration.

5. The scanner supports USB-KBW (Default), RS232, and USB Virtual
   Com data interfaces. To switch between modes, scan the
   corresponding barcode for each mode.

6. Configure the USB Keyboard Layout Control Character Escaping by
   scanning either “Enable” or “Disable (Default)” barcode.

7. Configure the CR/LF character processing under USB Keyboard
   mode by scanning the “Only 0A(LF) line feed”, “Only ODS (CR) line
   feed (Default)”, or “All convert to 0A (LF)/0D(CR)” barcode.

8. Set up the USB Keyboard Transfer Speed by scanning either “Low
   (Default)”, “Middle”, or “High” barcode. If the PC has a lower
   function, select a lower scanning speed for accuracy.

9. Change the keyboard layout to other available options by
   scanning the corresponding barcode for each option.

10. Turn on Virtual Keyboard mode, and select the mode that best
    suits your needs by scanning the corresponding barcode for each
    mode.

11. Select the Host Operating System in Virtual Keyboard mode by
    scanning either “WINDOWS (Default)”, “MAC OS”, or “LINUX”
    barcode.

12. In case of peculiar characters, use the manual to set up the
    barcode encoding configuration to ensure output accuracy.

2D Barcode Scanner Full Manual
V3.3F

Content
Connection Method …………………………………………………………………………………………………5 Enable/Disable Configuration barcode ………………………………………………………………………5 Version No. …………………………………………………………………………………………………………….5 Factory Default Setting …………………………………………………………………………………………… 5 Product User Configuration …………………………………………………………………………………….. 6 Data Interface …………………………………………………………………………………………………………6 USB Keyboard Layout ……………………………………………………………………………………………. 7
Control Character Escaping ………………………………………………………………………..7 Control Character Output ……………………………………………………………………………7 CR/LF character processing(USB Keyboard) ………………………………………………. 7 USB Keyboard Transfer Speed ………………………………………………………………….. 8 Convert Case …………………………………………………………………………………………… 9 Keyboard Layouts …………………………………………………………………………………….. 9 Virtual Keyboard ………………………………………………………………………………………13 Selection Of Host Operating System In Virtual Keyboard Mode …………………… 14 Barcode Encoding Configuration ……………………………………………………………….15 Output Encoding Format …………………………………………………………………………..15 Invoice Function ……………………………………………………………………………………… 16 Switch On/Off Invoice Function ………………………………………………………………… 16 Invoice Type …………………………………………………………………………………………… 17 RS232 Interface Configuration ………………………………………………………………………………. 17 Baud Rate ……………………………………………………………………………………………….17 Data bit, Stop bit, Parity bit ………………………………………………………………………. 18 GS Control Character Replacement ………………………………………………………………………. 20 Scan Mode ………………………………………………………………………………………………………….. 21 Auto Sense Mode off ………………………………………………………………………………..21 Auto Sense Mode on ………………………………………………………………………………..21 Repeat Barcode Detection ………………………………………………………………………..21 Light Configuration ………………………………………………………………………………………………..22 LED Indicator Light …………………………………………………………………………………..22 Buzzer Configuration ……………………………………………………………………………………………. 22 Volume Setting ……………………………………………………………………………………….. 22 Prompt Tone Setting …………………………………………………………………………………23 Successfully Decode Prompt Tone Setting ………………………………………………… 23 Successfully Decode Prompt Audio Frequency Setting (Tone) …………………….. 23 Successfully Decode Prompt Duration Setting …………………………………………… 24 Error Warning Prompt Frequency Setting (Tone) …………………………………………24 Prefix and Suffix Configuration ………………………………………………………………………………. 25 Start Character ……………………………………………………………………………………….. 25 Terminal Character …………………………………………………………………………………..25 Custom Prefix ………………………………………………………………………………………….26 Output Options ……………………………………………………………………………………….. 27
2

Edit …………………………………………………………………………………………………………27 Custom Suffix …………………………………………………………………………………………. 27 Output Options ……………………………………………………………………………………….. 27 Edit …………………………………………………………………………………………………………28 Code ID …………………………………………………………………………………………………. 28 Output Options ……………………………………………………………………………………….. 28 Edit …………………………………………………………………………………………………………29 AIM ID …………………………………………………………………………………………………….29 Barcode Prefix And Suffix Order Selection ………………………………………………….29 Prefix …………………………………………………………………………………………………….. 30 Suffix ………………………………………………………………………………………………………30 Data edition …………………………………………………………………………………………………………. 30 Transmission configuration ………………………………………………………………………. 31 Field Length Configuration ………………………………………………………………………..31 Inverse color barcode selection ………………………………………………………………………………32 Barcode Type Selection …………………………………………………………………………………………32 Enable/Disable All barcodes …………………………………………………………………….. 32 Enable/Disable All 1D barcodes ……………………………………………………………….. 33 Enable/Disable All 2D barcodes ……………………………………………………………….. 33 Codabar ………………………………………………………………………………………………….33 Codabar Start/Terminal Character ……………………………………………………………..34 Set Length Range For Codabar …………………………………………………………………34 Code 39 …………………………………………………………………………………………………. 34 Code 39 Parity Check ……………………………………………………………………………… 35 Code 39 Full ASCII …………………………………………………………………………………..35 Set Length Range For Code 39 …………………………………………………………………36 Code 32(Enable code39 first) …………………………………………………………………… 36 Interleaved 2 of 5 (ITF25) ………………………………………………………………………… 37 Interleaved 2 of 5 (ITF25) Check Bit …………………………………………………………..37 Interleaved 2 of 5 (ITF25) Length Selection ………………………………………………..38 Set Length Range for Interleaved 2 of 5 ……………………………………………………. 39 Industrial 2 of 5 ………………………………………………………………………………………..39 Set Length Range for Industrial 2 of 5 ………………………………………………………..40 Matrix 2 of 5 (4-24bit) ……………………………………………………………………………….40 Set Length Range for Matrix 2 of 5 …………………………………………………………….41 Code 93 …………………………………………………………………………………………………. 41 Set Length Range for Code 93 …………………………………………………………………. 41 Code 11 …………………………………………………………………………………………………. 42 Code 11 Parity Check Output …………………………………………………………………… 42 Code 11 Parity Selection …………………………………………………………………………..42 Set Length Range for Code 11 …………………………………………………………………. 43 Code 128 ……………………………………………………………………………………………….. 43 GS1-128 ………………………………………………………………………………………………… 43 Set Length Range for CODE-128 ………………………………………………………………44
3

UPC-A …………………………………………………………………………………………………… 44 UPC-A Check Bit ……………………………………………………………………………………..44 UPC-A Convert to EAN-13 ………………………………………………………………………..45 UPC-E …………………………………………………………………………………………………… 45 UPC-E Check Bit ……………………………………………………………………………………..45 UPC-E Expand to UPC-A ………………………………………………………………………… 46 EAN/JAN-8 …………………………………………………………………………………………….. 46 EAN-8 Convert to EAN-13 ……………………………………………………………………….. 46 EAN/JAN-13 …………………………………………………………………………………………… 47 EAN 13 Check Bit …………………………………………………………………………………… 47 UPC/EAN/JAN Add on code …………………………………………………………………….. 47 EAN13 Convert to ISBN ……………………………………………………………………………48 EAN13 Convert to ISSN ……………………………………………………………………………48 GS1 DataBar (RSS14) ……………………………………………………………………………..49 GS1 DataBar Limited ………………………………………………………………………………. 49 GS1 DataBar Expanded ………………………………………………………………………….. 49 PDF417 …………………………………………………………………………………………………. 50 Micro PDF417 ………………………………………………………………………………………… 50 QR Code …………………………………………………………………………………………………50 QR Code URL Link …………………………………………………………………………………..51 Micro QR ……………………………………………………………………………………………….. 51 Data Matrix …………………………………………………………………………………………….. 51 Aztec Code ……………………………………………………………………………………………..52 Appendix …………………………………………………………………………………………………………….. 52 Data and Edit barcode …………………………………………………………………………….. 52 Barcode type ID Table ………………………………………………………………………………55 AIM ID Table …………………………………………………………………………………………… 56 Visible Character ASCII Table ……………………………………………………………………56 Control Character Set (USB keyboard mode) ……………………………………………..57 Control Character Set (RS232,USB,VCP) …………………………………………………. 58 Configuration of instructions and examples ……………………………………………….. 59 Example for user-defined prefix and suffix: ………………………………………………… 59 Example for barcode length range configuration ………………………………………… 60 Example for USB keyboard transmit speed configuration ……………………………. 61
4

Connection Method
Put scanner connect the dedicated joint, on the other side plug into PC port. If the barcode configuration was turned off, please turn on the barcode configuration .
Enable/Disable Configuration barcode
Scanner can set up when enabled barcode function.In contrast, the scanner can’t set up if disabled. Need to switch on and set up again.
Enable Configuration Function (Default)

Version No.

Disable Configuration Function

Version Number
Factory Default Setting
Scanning the below barcode can restore the scanner the factory default.

Restore Factory Default Configuration 5

Product User Configuration
Scanning the below barcode can save current parameters as user’s configuration.

Save Scanning the below barcode can restore for saved user’s configuration.

Data Interface

Restore User Configuration

This scanner support USB-KBW, RS232, USB Virtual Com. Scanning the below barcode is USB-KBW mode.

USB-KBW (Default) Scanning the below barcode is RS 232 mode.

RS232 Scanning the below barcode is USB Virtual Com mode(driver is needed).

6

USB Virtual Com
USB Keyboard Layout Control Character Escaping
Enable
Disable (Default)
Control Character Output
Disable
Enable
CR/LF character processing(USB Keyboard)
Only 0A(LF) line feed 7

Only 0D (CR) line feed (Default)
All convert to 0A (LF)/0D(CR)
USB Keyboard Transfer Speed
Used for set up scanning speed under USB keyboard mode. If PC in a lower function, please choose low scanning speed to make sure its accuracy.
Low (Default)
Middle
High
Custom Sending Speed (2ms~50ms) 8

Convert Case

Original data (Default)

All Convert to Upper Case

Case Inversion

Keyboard Layouts

All Convert to Lower case

English (United States) (Default)
French (France)
9

Italian (Italy)

Italian 142 (Italy)

German (Germany) Spanish (Spain)
Spanish (Latin America) Finnish
Japanese 10

Russian (MS) Russian (typewriter)
Arabic (101) Irish
Polish (214) Polish (Programmers)
Dutch (Netherlands) 11

Czech (QWERTZ)

Portuguese (Portugal)

Portuguese (Brazil) Swedish (Sweden)
Turkish Q Turkish F
Greek (MS) 12

French (Belgium)
English (UK)
Hungarian
Hungarian 101-KEY
Vietnamese
Slovak
Virtual Keyboard
Mode 1: Do not support output the characters between 0x20 to 0xFF by using the virtual keyboard, under the current keyboard layout. The characters between 0x00~0x1F are output according to the definition of control characters (Refer to Appendix)
13

Model 2: Support output the characters between 0x20 to 0xFF by using the virtual keyboard. The characters between 0x00~0x1F are output according to the definition of control characters (Refer to Appendix) Model 3: Support output the characters between 0x00 0xFF by using the virtual keyboard
Turn Off (Default)
Turn On (Mode 1)
Turn On (Mode 2)
Turn On (Mode 3)
Selection Of Host Operating System In Virtual Keyboard Mode
14

WINDOWS (Default)
MAC OS
LINUX
Barcode Encoding Configuration
In a normal situation , the barcode encoding was identified accurately. Please use manual to set up if encountered peculiar characters, that make sure output barcode content correctly.
Auto (Default)
KOI8-R code
Output Encoding Format
To output correctly in the specified encoding format. For example: It’s GBK code when output in the Notepad /Excel; It’s UNICODE when output in the Word.
15

When output is English/Latin-1 encode format, the output mode will affected by the function switch of virtual keyboard. When output is GBK/UNICODE, the output mode will compelled to virtual keyboard.
English/Latin-1 (Default)
GBK (Notepad/excel)
UNICODE (Word)
Invoice Function Switch On/Off Invoice Function
OFF (Default)
On To ensure the correct output of the invoice content, when switch on the invoice code function, please configure the Chinese character output mode to GBK code (Notepad/Excel), and at the same time switch off like Code ID, User- defined prefix/suffix, and starting character to change original barcode content function.
16

Invoice Type
VAT Invoice (Special) (Default)

RS232 Interface Configuration Baud Rate

VAT Invoice (Normal)

4800 19200

9600 (Default)

38400 17

57600
Data bit, Stop bit, Parity bit

115200

7 Bit, 1 Stop Bit, No Parity 7 Bit,1 Stop Bit, Even Parity
7 Bit,1 Stop Bit, Odd Parity 7 Bit, 2 Stop Bit, No Parity
7 Bit, 2 Stop Bit, Even Parity 18

7 Bit,2 Stop Bit, Odd Parity 8 Bit,1 Stop Bit, No Parity(Default)
8 Bit,1 Stop Bit, Even Parity 8 Bit,1 Stop Bit, Odd Parity
8 Bit,2 stop Bit, No Parity 8 Bit,2 Stop Bit, Even Parity
8 Bit,2 Stop Bit, Odd Parity 19

GS Control Character Replacement
Do Not Replace (Default) When output character is “Ç”, please first to scan” Virtual keyboard (Mode one or Mode two or Mode three)”.
Replace Ç Replace |
Replace ^] Replace ] Replace 20

Scan Mode Auto Sense Mode off
Decoding by pulling the trigger of the scanner when auto sense mode is off. It’s default mode.
Off (Default)
Auto Sense Mode on
The scanner can sense barcode for decoding automatically.
On
Repeat Barcode Detection
Use for decode same barcode of interval time, it will decode only one time if not exceeded set time.
500ms
750ms (Default) 21

1s
2s
Light Configuration LED Indicator Light

Off
Buzzer Configuration Volume Setting

On (Default)

Low 22

Prompt Tone Setting

High (Default)

Off
On (Default)
Successfully Decode Prompt Tone Setting

Off On (Default)
Successfully Decode Prompt Audio Frequency Setting (Tone)

23

1 (Default)
2
3
Custom
Successfully Decode Prompt Duration Setting
Long (Default)
Short
Error Warning Prompt Frequency Setting (Tone)
There will be four consecutive error warning tones if data transmission fails, and a single error warning tone when the unrecognized configuration code is scanned.
24

Low (Default) Middle
High
Prefix and Suffix Configuration Start Character
None (Default) STX
Terminal Character
25

None LF
TAB
Custom Prefix

Enter CR/LF (Default)
ETX

26

Output Options
On

Edit
Clear All Custom Prefix

Off (Default)

Set Custom Prefix (Please set up ID Table ,Data, and edit barcode refer to the appendix after scanning.)
Custom Suffix Output Options
On

27

Edit
Clear All Custom Suffix

Off (Default)

Set Custom Suffix (Please set up ID Table ,Data, and edit barcode refer to the appendix after scanning.)
Code ID Output Options
Off (Default)

Before Switch on

After Switch On 28

Edit
Set Custom Prefix (Please set up ID Table ,Data, and edit barcode refer to the appendix after scanning.)

AIM ID

Clear All Custom Prefix

Off (Default)
Before Switch On
After Switch On
Barcode Prefix And Suffix Order Selection

29

Prefix
Start Character+CODE ID+AIM ID+Custom Prefix (Default)

Suffix

Start Character+ Custom Prefix + CODE ID+AIM ID

Custom Suffix+CODE ID+AIM ID+Terminal Character (Default)

CODE ID+AIM ID+Custom Suffix+Terminal Character
Data edition
The Data editing function can customize the barcode content into the three fields of Start/Center/End by configuring the Start/End field length. Please configure the length of the Start/End field and the transport configuration according to the actual needs.
Note: Custom presuffix, start, end, CODE ID, AIM ID and other non-barcode content will not be affected by the data editing function.

30

Transmission configuration

Transfer the full Data field

Only transfer the Start field

Only transfer the Center field

Field Length Configuration

Only transfer the End field

Set Start field length Set End field length
31

Inverse color barcode selection (Only 1D/DataMatrix/Aztec)
Normal Color
Inverse Color
Both (Normal/Inverse)
Barcode Type Selection Enable/Disable All barcodes
Enable all barcodes will low down decoding speed. So, we suggest you switch on scanner when needed. (Default is switch on state)
Enable All
Disable All 32

Enable/Disable All 1D barcodes
Enable All

Enable/Disable All 2D barcodes

Disable All

Enable All
Codabar

Disable All

Enable 33

Codabar Start/Terminal Character

Disable

Not Send Codabar Start/Terminal Character (Default)

Send Codabar Start/Terminal Character
Set Length Range For Codabar
Minimum Length (0~50bit)

Code 39

Maximum Length (0~50bit)

Enable 34

Code 39 Parity Check
Disable (Default)

Disable

Enable But Not Transfer

Enable & Transfer
Code 39 Full ASCII
Enable

Disable (Default) 35

Set Length Range For Code 39
Minimum Length (0~50bit)

Code 32(Enable code39 first)

Maximum (0~50bit)

Enable
Code 32 Prefix

Disable

Enable
Disable 36

Interleaved 2 of 5 (ITF25)

Enable

Interleaved 2 of 5 (ITF25) Check Bit

Disable

Disable Check Bit (Default)

Enable Check and Not Send Check Bit

Enable Check & Send Check Bit

37

Interleaved 2 of 5 (ITF25) Length Selection
Random Length (6-50bit) (Default) 6 Bit
8 Bit 10 Bit
12 Bit 14 Bit
16 Bit 38

18 Bit

20 Bit

22 Bit

24 Bit
Set Length Range for Interleaved 2 of 5
Minimum (0~50bit)

Industrial 2 of 5

Maximum (0~50bit)

39

Enable

Set Length Range for Industrial 2 of 5

Disable

Minimum (0~50bit)

Matrix 2 of 5 (4-24bit)

Maximum (0~50bit)

Enable
Disable 40

Set Length Range for Matrix 2 of 5
Minimum (0~50bit)

Code 93

Maximum (0~50bit)

Enable

Set Length Range for Code 93
Minimum (0~50bit)

Disable

Maximum (0~50bit) 41

Code 11

Enable

Code 11 Parity Check Output

Disable (Default)

Enable

Code 11 Parity Selection
Disable (Default)

Disable (Default)

1 Bit 42

2 Bit
Set Length Range for Code 11
Minimum (0~50bit)

Code 128

Maximum (0~50bit)

Enable

GS1-128

Disable

Enable 43

Set Length Range for CODE-128

Disable

Minimum (0~50bit)

UPC-A

Maximum (0~50bit)

Enable

UPC-A Check Bit

Disable

Send UPC-A Check Bit (Default) 44

UPC-A Convert to EAN-13

Not send UPC-A Check Bit

Enable UPC-A convert to EAN-13

UPC-E

Disable UPC-A convert to EAN-13 (Default)

Enable
UPC-E Check Bit

Disable

Send UPC-E Check Bit (Default) 45

UPC-E Expand to UPC-A

Not send UPC-E Check bit

Enable

EAN/JAN-8

Disable (Default)

Enable

EAN-8 Convert to EAN-13

Disable

Disable EAN-8 convert to EAN-13 46

EAN/JAN-13

Enable EAN-8 convert to EAN-13

Enable
EAN 13 Check Bit

Disable

Send EAN13 Check Bit (Default)

UPC/EAN/JAN Add on code

Don’t Send EAN13 Check Bit

47

Ignore UPC/EAN/JAN (Default)
Decode UPC/EAN/JAN
Custom UPC/EAN/JANA add on code
EAN13 Convert to ISBN

Enable
EAN13 Convert to ISSN

Disable (Default)

Enable
Disable (Default) 48

GS1 DataBar (RSS14)
Enable
GS1 DataBar Limited
Enable
GS1 DataBar Expanded
Enable

Disable Disable

49

PDF417
Enable
Micro PDF417
Enable
QR Code
Enable

Disable Disable
Disable

50

QR Code URL Link
Disable
Micro QR
Enable
Data Matrix
Enable

Disable Enable Disable

51

Aztec Code
Enable
Appendix Data and Edit barcode
0
2

Disable Disable 1

52

3 4
5 6
7
8 9
53

A B
C D
E F
Cancel current setting Cancel a string of data from previous read 54

Cancel the data from previous read

Barcode type ID Table
Code type All codes Codabar Code128 Code32 Code93 Code39 Code11 EAN-13
EAN-8 GS1 DataBar GS1-128 (EAN-128)
2 of 5 Interleaved 2 of 5
Matrix 2 of 5 Industry 2 of 5/IATA
UPC-A UPC-E ISBN ISSN
MSI Aztec Code DataMatrix
PDF417 Micro PDF417
QR Code Micro QR Code

HEX 99 61 6A 3C 69 62 48 64 64 52 6A
65 76 44 63 63 42 6E 6D 7A 75 72 53 51 51

55

Save
CODE
a j < i b H d d R j
e v D c c B n m z u r S Q Q

AIM ID Table
Code type Codabar Code128 Code32 Code93 Code39 Code11 EAN-13 / EAN-8 GS1 DataBar GS1-128 (EAN-128) Interleaved 2 of 5 Matrix 2 of 5 Industry 2 of 5 UPC-A / UPC-E
ISBN ISSN Aztec Code DataMatrix PDF417 / Micro PDF417 QR Code / Micro QR Code

AIM ID ]Fm ]C0 ]A0 ]G0 ]Am ]Hm ]Em ]e0 ]C1 ]Im ]X0 ]S0 ]Em ]X0 ]X0 ]z0 ]dm ]Lm ]Qm

Description m0~1
m0124
m013457 m01389 m0134
m013
m03
m: 0~6 m: 0~5 m: 0~6

Visible Character ASCII Table

Decimal 32 33 34 35 36 37 38 39 40 41 42 43 44

Hexadectimal 20 21 22 23 24 25 26 27 28 29 2A 2B 2C

Character
! ” # $ % & ` ( ) * + ,

Decimal 80 81 82 83 84 85 86 87 88 89 90 91 92

Hexadectimal 50 51 52 53 54 55 56 57 58 59 5A 5B 5C

Character P Q R S T U V W X Y Z [

56

45

2D

–

93

5D

]

46

2E

.

94

5E

^

47

2F

/

95

5F

_

48

30

0

96

60

`

49

31

1

97

61

a

50

32

2

98

62

b

51

33

3

99

63

c

52

34

4

100

64

d

53

35

5

101

65

e

54

36

6

102

66

f

55

37

7

103

67

g

56

38

8

104

68

h

57

39

9

105

69

i

58

3A

:

106

6A

j

59

3B

;

107

6B

k

60

3C

<

108

6C

l

61

3D

=

109

6D

m

62

3E

110

6E

n

63

3F

?

111

6F

o

64

40

@

112

70

p

65

41

A

113

71

q

66

42

B

114

72

r

67

43

C

115

73

s

68

44

D

116

74

t

69

45

E

117

75

u

70

46

F

118

76

v

71

47

G

119

77

w

72

48

H

120

78

x

73

49

I

121

79

y

74

4A

J

122

7A

z

75

4B

K

123

7B

{

76

4C

L

124

7C

|

77

4D

M

125

7D

}

78

4E

N

126

7E

~

79

4F

O

Control Character Set (USB keyboard mode)

Decimal 0

Hexadecimal 00

Correspondingkeyvalue (disable CODE ID) reserve

Correspondingkeyvalue (enable CODE ID) Ctrl+@

57

1

01

Insert

Ctrl+A

2

02

Home

Ctrl+B

3

03

End

Ctrl+C

4

04

Delete

Ctrl+D

5

05

Page Up

Ctrl+E

6

06

Page Down

Ctrl+F

7

07

ESC

Ctrl+G

8

08

Backspace

Ctrl+H

9

09

Tab

Ctrl+I

EnterThe

10

0A

configuration of CRLF processing decide how

Ctrl+J

it express

11

0B

Caps Lock

Ctrl+K

12

0C

Print Screen

Ctrl+L

EnterThe

13

0D

configuration of CRLF processing decide how

Ctrl+M

it express

14

0E

Scroll Lock

Ctrl+N

15

0F

Pause/Break

Ctrl+O

16

10

F11

Ctrl+P

17

11

Direction key

Ctrl+Q

18

12

Direction key

Ctrl+R

19

13

Direction key

Ctrl+S

20

14

Direction key

Ctrl+T

21

15

F12

Ctrl+U

22

16

F1

Ctrl+V

23

17

F2

Ctrl+W

24

18

F3

Ctrl+X

25

19

F4

Ctrl+Y

26

1A

F5

Ctrl+Z

27

1B

F6

Ctrl+[

28

1C

F7

Ctrl+

29

1D

F8

Ctrl+]

30

1E

F9

Ctrl+^

31

1F

F10

Ctrl+_

Control Character Set (RS232,USB,VCP)

Decimal

Hexadecimal

58

Character

0

00

NUL

1

01

SOH

2

02

STX

3

03

ETX

4

04

EOT

5

05

ENQ

6

06

ACK

7

07

BEL

8

08

BS

9

09

HT

10

0A

LF

11

0B

VT

12

0C

FF

13

0D

CR

14

0E

SO

15

0F

SI

16

10

DLE

17

11

DC1

18

12

DC2

19

13

DC3

20

14

DC4

21

15

NAK

22

16

SYN

23

17

ETB

24

18

CAN

25

19

EM

26

1A

SUB

27

1B

ESC

28

1C

FS

29

1D

GS

30

1E

RS

31

1F

US

Configuration of instructions and examples
Example for user-defined prefix and suffix:
You can edit 10 characters as prefix or suffix. (In order to make sure the prefix and suffix can output normally, please enable user-defined prefix or suffix first) Example 1.1:
59

Set” XYZ” as prefix on all codes Before set up , please search HEX value for all codes is “99” (Appendix: barcode type ID Table); find “X””Y””Z” HEX value is “58””59″”5A” (Appendix:Visible Character ASCII Table)
Step: Set “User-defined Prefix”; Set ” 9″”9″”5″”8″”5″”9″”5″”A” (Appendix: data and edit barcode); Set”Save”.
If you want to revise the scanned barcode before save, please set up “Cancel the data from previous read” or”Cancel a string of data from previous read” to reset. If you want to give up setting scan , then scan” Cancel current setting”.
Example 1.2:
Set “R” as prefix on QR Before set up, please search HEX value for QR code is “51”(Appendix: barcode type ID Table); find”R” HEX value is “52” (Appendix:Visible Character ASCII Table)
Step: Set ” Custom prefix”; Set”5″”1″”5″”2″ (Appendix: data and edit barcode); Set” Save”.
Example 1.3:
Cancel Custom prefix in QR code
Step: Set” Custom prefix”; Set”5″”1″; Set” Save” Note: If set up prefix on all QR codes, it will default all QR codes prefix after set up. In contrast, if cancel all prefix / suffix on barcodes, please set ” Clear All Custom Prefix” and “Clear All Custom Suffix”.
Example for barcode length range configuration
Please sure it not bigger than current maximum length range when set up minimum length. Otherwise, it will show error. In the same way, must be make sure it’s not smaller than current minimum length range when set up maximum length.
Example 2.1:
Set Code 128 length range is 4-12bit Step: Set “Code 128 Minimum0~50bit”; Set”4″; Set “Save” Set “Code 128 Maximum (0+-50bit)”; Set”1″”2″; Set “Save”
Example 2.2:
Set Interleaved 2 of 5 length is 14bit 60

It can set up by “ITF25 14bit”, through barcode length range of Maximum /Minimum to set,too. Step: Set” Interleave 2 of 5 Minimum0~50bit”; Set”1″”4″; Set”Save” Set” Interleave 2 of 5 Maximum (0+50bit)”; Set”1″”4″; Set”Save” Example 2.3: Set Code 39 length is random length Step: Set” Code 39 Minimum 0~50bit “; Set”0″ ; Set”Save” Set”Code 39 Maximum (0+50bit)”; Set”0″; Set “Save”
Example for USB keyboard transmit speed configuration
If PC in a lower function, it will appear error status. Need to set up a slow scanning speed with customized under USB keyboard mode. Such as: 50ms Step: Set”Custom Sending Speed”; Set”5″”0″;Set”Save” Warning Tone It will appear error warning for 4 times in a continue while transfer failure barcode. Please check if it’s normal work when appear this situation.
Read Skills To get a good reading performance, a beam of aim light from scanner should be aimed at the centre of barcode, support to aim in any directions for read convenient,too. More nearly barcode, the beam of aim light is smaller; More further barcode, the beam of aim light bigger. For reading barcode correctly, if barcode small, the scanner should be close to barcode, if barcode big, the scanner should be farther to barcode. If the barcode is highly reflective (for example: coated surface), please adjust the scanner angle to read it successfully.
61

Safety Please not direct aim eye when the scanner has a strong ray of light, to avoid causing any hurt or unwell.
62

References

• 我的私人小站
• SUNLUX IOT Technology (Guangdong) Inc.|ESL|RFID|electronic label|Scan Code|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>