User Manual

ECC9312K, ECC9310S,ECC9232K
Electrolux Range Hood

Customer Care and Service

The following symbols will be used in this manual, with their explanations as follows:
Warning! Important information relating to the protection of personal safety and avoidance of electrical damage.
General information and advice
Environmental protection information

Product Description

The romantic European range hood has the following six advantages:

1. **** Futuristic design, up-to-date styling Streamlined design, elegant and stylish appearance, and touch control, fully show the cooking experience of blues style.
2. **** Large suction and complete removal of fume The integral stretched hood is more suitable for the fume collection area of kitchens, and the fan with a large exhaust rate is used to exhaust fume more thoroughly.
3. Low noise According to the principle of aerodynamics, a well-designed exhaust system guarantees smooth and quiet operation.
4. **** Easy maintenance Large conical strainers for air intake are designed on f o u r sides to ensure thorough fume suction, avoid spillage of residual oil, and smoothly converge residual oil into the oil cup while avoiding the weakness in the maintenance of traditional European range hoods.
5. **** Circuit characteristics A unique multi-circuit design is used to ensure no accumulation, n o dripping, or seepage.

Precaution

1 Child Safety

1. Do not allow children to extend their fingers or other parts of the body into the range hood.
Warning: Destroy or recycle the appliance’s carton, plastic bags, and any other exterior wrapping material immediately after the product is unpacked. Children should never play with these items. The danger of suffocation!
(2) Precautions for Use

1. ****Always use a power supply compliant with the requirements of the appliance. A three-pin power socket must be reliably grounded.
2. **** The wall on which the range hood will be installed should be strong enough to bear the dead weight of the range hood itself. The wall must be non-combustible.
3. **** Do not expose the range hood to fire directly.
4. **** Protect the motor, switches, and other electrical parts against water.
5. **** Do not change the specifications of electrical parts, change the internal circuit, or connect other lines.
6. **** Do not scratch, knot, or squeeze the power cable.
7. **** If any abnormal conditions occur during use, refer to the troubleshooting section for solutions before contacting the customer service center. If the fault persists, unplug the power plug of the range hood and contact our customer service center.
8. **** If the light is damaged, replace it with a new one with the same specifications.
9. **** This appliance is for household use only instead of for unintended purposes.
10. **** When oil residue stored in the oil cup reaches two-thirds of its capacity, clean immediately to prevent spillage.
11. Do not dismantle and repair the appliance without authorization. Otherwise, serious consequences may be followed.
12. If users do not clean the range hood according to the instructions, there is a risk of fire.
13. The room must be well-ventilated when the range hood is used in a place where gas or other fuel is combusted (but the range hood should not be installed in a place with large convection. Otherwise, the suction performance will be degraded).
14. The gas discharged from the range hood cannot be discharged into the waste smoke tube of burning gas or other fuels.
    (3) Environmental Protection
    “Environmental protection, the benefit of mankind, pollution prevention, and continuous improvement” are the philosophy of our company’s environmental management.  The environmental impact caused by our products in use and after service life is hereby warned to you as follows: Waste cartons and plastic bags are recyclable while the waste foam is not. Properly classify these wastes after unpacking.

Packing List

Please check the items in the package against the packing list. If there is any missing or lost items:

1. Please ask the vendor to handle this if it is the responsibility of the company or vendor.
2. Please contact the vendor or the company if it is your responsibility.

ECC93105
One                 ECC9312K
Two                 ECC9232K
3| Warranty card| 1 pcs
4| Oil cup| 1 pcs
5| Appliance
mounting plate| 1 pcs| 10| Special screws for decorative cover, safety block, ST5X19 screws, expansion tube, and wood screws| 1 bag
6| Air outlet| 1 pcs
7| Aluminum foil tube| 1 pcs

Technical Specifications

Schematic Circuit Diagram

Installation Instructions

I . Installation Requirements

1. The wall on which the appliance is installed should be strong enough to bear the dead weight of the appliance.
2. The range hood must not be in contact with the electrical lines inside and outside the wall. Otherwise, there is a risk of electric shock.
3. The range hood should not be installed in a place with large convection. Otherwise, the suction performance will be degraded.
4. The range hood should be securely installed on the wall 650 mm above the cooker. The lower the height, the better the suction performance.
5. The distance between the air outlet of the range hood and the upper exhaust hole should be less than or equal to 1.5 m, so as to avoid degraded suction performance  because of too long air out let or too many turns (generally one turn)
6. The following figure shows the installation dimension of the air outlet when it is mounted to the cupboard or ceiling.

Il. Installation Method

1. The distance from the bottom of the range hood to the cookware supporting surface on the stove should be at least 650mm. If the installation instructions for the gas stove specify a greater distance, it should be considered.
2. Identify the hole location, drill two holes with a diameter of 10 mm, a depth of 53 mm, and a spacing of 180 mm on the wall, and bury the expansion pipes in the holes.
3. Secure the mounting plate to the wall with two 05 x 53 mm wood screws. Note: Avoid electric wires inside the wall while drilling. Otherwise, there is a risk of electric shock.
4. Remove the eight self-tapping screws from the air outlet assembly using a Phillips screwdriver, and remove the rubber gasket.
5. Place the rubber gasket and air outlet assembly onto the air outlet in turns, and align them with the screw holes. After the screw holes are aligned, secure the rubber gasket and air outlet assembly to the mainframe using the eight self-tapping screws removed in Step 1.
6. By referring to the figure, remove the smoke tube and short adapter (both have been secured with aluminum foil tape) (the smoke tube and adapter are accessories, not in the product package) so that the smoke tube is compressed. Pass the air outlet cover from top to bottom through the smoke tube and short adapter to the end. Then fasten and interlock the above assembly to the air outlet seat with the four buckles on the air outlet cover. Connect the power supply, start the motor, and check whether the two metal pieces turn up. The two metal pieces should fall back naturally when the appliance is turned off.
7. Lift the appliance, align the hanging holes on the back of the mainframe with the hooks on the mounting plate, and check that the appliance is installed horizontally and stably. Use one screw (ST5x19) to fix the appliance block on the wall through the plastic expansion pipe to prevent the appliance from falling off in the vertical direction when it is subjected to external forces.
8. Direct connection is possible when the aperture of the smoke outlet on the kitchen wall is larger than the outer diameter of the exhaust pipe. Otherwise, cut off the excess part of the exhaust pipe connector smaller than the smoke outlet as required, connect the exhaust pipe and exhaust pipe connector with adhesive tape, and install it into the smoke outlet.
9. If you connect the exhaust pipe directly to the outside, extend the exhaust pipe at least 30 mm out of the wall, with the air outlet slightly tilting down to avoid backflow of rainwater.
10. To install a decorative cover, determine the position of the mounting hole of the decorative cover mounting plate according to the installation diagram.
11. ( ECC9310S/ ECC9312K): Drill two holes with a diameter of 10 mm and a depth of 50 mm with an electric impact drill at the corresponding positions, bury plastic expansion pipes and fix the upper decorative cover bracket on the wall with two screws (05 x 53).
12. ( ECC9232K): Drill four holes with a diameter of 10 mm and a depth of 50 mm with an electric impact drill at the corresponding positions, bury plastic expansion pipe, and fix the two upper decorative cover brackets on the wall with four screws (05 x 53). (12) ( ECC9310S/ ECC9312K): Pull out the upper decorative cover, adjust the height of the upper decorative cover and hook it to the mounting hole. Align the holes on both sides of the upper decorative cover with the anchor holes of the bracket, and secure them with two stainless steel screws (M4 x 12) with gaskets. (Note: Be careful while pulling out the upper cover and pay attention to sharp edges around the product to avoid cuts.) ( ECC9232K): Pull out the upper decorative cover, adjust the height of the upper decorative cover and hook it to the mounting hole. Align the holes on both sides of the upper decorative cover with the anchor holes of the bracket, and secure them with four stainless steel screws (M4 x 12) with gaskets. (Note: Be careful while pulling out the upper cover and pay attention to sharp edges around the product to avoid cuts.) Align the hanging lugs at both ends of the oil cup with the slots on the two oil cup brackets at the lower end of the rear of the range hood, push the oil cup horizontally inward, and check that the oil cup is securely installed.

III. Installation Checks The user should first check whether the range hoop is well installed.
IV. Power Settings After checking that the appliance is properly installed, plug the power plug of the appliance into a power socket that is reliably grounded.

Instructions for Use

1. The instructions for use of the Power button of ECC9310S
   Power
   When you tap the “Power” button, the buzzer sounds, and all buttons are lit up in white. The red LED indicator lights to turn on from left to right for 0.1 seconds. In the final 0.6 seconds, if there is a speed setting memory, the fan is turned on in the memorized speed setting. Otherwise, the fan is turned on in speed 2 when the appliance is on, and the red power indicator light and red indicator lights for the corresponding speed setting and lower speed setting are turned on. With power on, when you tap the “Power” button, the buzzer sounds, all the buttons are turned off, and the appliance is turned off (The light is not affected).
   Fan Speed Settings
   With power on, you can tap the “1”, “2” or “3” buttons to set the fan speed with a beep sound. The indicator light for the fan speed button you tap and the indicator lights with the lower speed settings are displayed in red. You can switch fan speed freely among “1”, “2” and “3” by tapping the fan speed key.
   Stir-fry
   With power on, when you tap the “Stir-fry” button, the buzzer sounds, and the red indicator lights for the fan speed and the button will be displayed. The fan will return to the original speed setting after the speed setting in stir- fry mode runs for 1 minute. When you tap the “Stir-fry” button again within 1 minute, the fan will restore its original speed setting with a beep sound. Directly press other speed setting buttons to enter the corresponding speed setting.
   Light
   In standby/on state, when you tap the “Light” button, the buzzer sounds, the Light button is lit up, the corresponding red indicator light is lit up, and the light turns on. You can tap the “Light’ button again to turn off the indicator light and the light.
   Delay Shutdown
   With the fan on, when you tap the “Delay” button, the buzzer sounds, the red indicator light for the Delay button blinks, and the system start to execute the “Delay Shutdown” function. The fan runs in speed setting 1 and the red indicator light for speed setting 1 turns on. The appliance shuts down after 5 minutes. You can tap the “Delay” button again in “Delay Shutdown” mode to disable the delay shutdown function. Upon completion of delay shutdown, the appliance is shut down and the light turns off.
   Strainer Clean
   After the appliance is powered on for the first time, the system will accumulate the operation time of the appliance. When the operation time reaches 50 hours, the red indicator light for the Clean button will blink. Users need to remove the strainer for cleaning. Press and hold the “Strainer Clean” button for 3 seconds after the strainer is reinstalled to clear the alarm (The 50-hour timer starts again).

2. The instructions for use of the Power button of ECC9312KPower
   When you tap the “Power” button or wave your hand right, the buzzer sounds and all white button indicator lights are lit up. The red LED indicator lights to turn on from left to right for 0.1 seconds. In the last 0.6 seconds, if there is a speed setting memory, the fan is turned on in the memorized speed setting. Otherwise, the fan is turned on in speed 2, and the red power indicator light, the red indicator light for the corresponding speed setting, and the ventilation indicator light are turned on. The appliance is powered on.
   With power on, when you tap the “Power” button, the buzzer sounds, all the buttons are turned off, and the appliance is turned off. The flap at the air inlet is closed.
   Fan Speed Settings
   With power on, you can tap the “1”, “2”, “3”, “4”, or “5” buttons or wave your hand left or right to set the fan speed with a beep sound. The indicator light for the fan speed button you tap, the ventilation indicator light, and the indicator lights with lower speed settings are displayed in red. You can switch fan speed freely among “1”, “2”, “3”, “4”, and “5” by tapping the fan speed key.
   Stir-fry
   With power on, when you tap the “Stir-fry” button, all the speed settings are displayed. The fan will return to the original speed setting after the speed setting in stir-fry mode runs for 1 minute. When you tap the “Stir-fry” button again within 1 minute, the fan will restore its original speed setting with a beep sound.
   Ventilation
   With power on, when you tap the “Vent” button, the ventilation function is enabled, and the red indicator light for the button blinks. The fan runs for 5 minutes in a speed setting of 1 every hour. You can tap the “Vent” button again or swipe right to cancel ventilation. The fan starts in speed setting 2. You can tap the “Power” button or swipe left to shut down the appliance.
   Light
   In standby/on state, when you tap the “Light” button, the buzzer sounds, the Light button is lit up, the corresponding red indicator light is lit up, and the light turns on. You can tap the “Light’ button again to turn off the indicator light and the light.
   Delay Shutdown
   With the fan on, when you tap the “Delay” button or control the appliance with a gesture, that is, swiping left in speed setting 1, the buzzer sounds, the red indicator light for the Delay button blinks and the red indicator light for speed setting 1 turns on, and the system starts to execute the “Delay Shutdown” function. The fan runs in speed setting 1 and stops after 5 minutes. You can tap the “Delay” button again in “Delay Shutdown” mode to disable the delay shutdown function. Upon completion of delay shutdown, the appliance is shut down and the light turns off.
   Strainer Clean
   After the appliance is powered on for the first time, the system will accumulate the operation time of the appliance. When the operation time reaches 50 hours, the red indicator light for the Clean button will blink. Users need to remove the strainer for cleaning. Press and hold the “Strainer Clean” button for 3 seconds after the strainer is reinstalled to clear the alarm (The 50-hour timer starts again).
   Gesture Settings
   With power off, press and hold the “Power” button for 3 seconds to enter the gesture setting mode. Tap the “1” button. The red indicator light turns on and the gesture function is enabled. Tap the “2” button. The red indicator light turns on and the gesture function is disabled. In gesture setting mode, if you tap the “Power” button or “Light” button, or the appliance is inactive for 3 seconds, the appliance is turned off and the gesture function is set (The gesture function is enabled by default).
   Gesture Function
   When the appliance is turned off, if you wave your hand left, the appliance remains off without response. You can wave your hand right to start the appliance. The appliance starts in speed setting 2 for the first time. The appliance will start in the last speed setting in later uses (not ventilation or delay mode). When the appliance is operating, you can wave your hand left to reduce the speed setting from stir fry, 5, 4, 3, 2, 1, delay shutdown to shutdown, or wave your hand right to increase the speed setting from 1, 2, 3, 4, 5 to stir fry, and then maintain at the stir fry mode without other response. When the delay shutdown function is enabled, you can wave your hand left to shut down the appliance or wave your hand right to start the appliance in speed setting 2. When the ventilation function is enabled, you can wave your hand left to shut down the appliance or wave your hand right to start the appliance in speed setting 2. In gesture setting mode, the appliance does not respond when you wave your hand left or right.

3. The instructions for use of the Power button of ECC9232K Off State
   With power off, all white button indicator lights are turned off. You can tap the “Light” button to turn on the light and tap the button again to turn off the light. The related white button indicator light will be steadily on when the light is turned on. You can tap the Power button to start the appliance. If a speed has been set, the fan starts in the speed setting. Otherwise, the fan starts in speed setting 2. The Power, +/-, Light, and Stir-fry buttons are steadily on, and the Nixie tube displays corresponding numeric values (Note: “b” is displayed for “Stir-fry”).
   On State
   With power on, the Power, +/-, and Stir-fry buttons are steadily on, and the Nixie tube displays the corresponding speed setting. The status of other button indicators depends on the status of corresponding functions.
   You can tap the “Light” button to turn on the light and tap the button again to turn off the light. The related white button indicator light will be steadily on when the light is turned on. If the appliance operates for 50 hours, the white cleaning indicator light blinks. In this case, press and hold the Clean button for 3 seconds. The white button indicator light turns off, the accumulated time is cleared, and the timer starts again.
   When you tap the + button, if the current speed setting is lower than 5, the speed is increased. Otherwise, the speed setting remains unchanged.
   When you tap the – button, if the current speed setting is greater than 1, the speed is reduced. Otherwise, the speed remains unchanged.
   When you tap the Power button, the appliance is shut down, and the status of the light is not affected.
   When you tap the Stir-fry button, the appliance runs in Stir Fry mode for one minute. The original speed setting resumes after one minute or when you tap the button again. The appliance does not respond if you tap the + button within one minute. When you tap the – button, the speed setting 5 is enabled.
   With power on, you can tap the Power button to turn off the appliance, and the status of the light is not affected.

Removal of the light:
(1) Removal of the light for CC9232K:

1. Extend a small slotted screwdriver or similar objects into the gap between the light cover and the hood.|  2. Pry up the light from the hood and disconnect the connector. The light can be replaced.

(2) Removal of the light for ECC9310S/ ECC9312 :

1. Remove the power plug| 2 Pry up the light with a small slotted screwdriver and remove it,
and then replace it with a new light of the same specifications.

Removal of the switch:

Unscrew the top cover in the upper part of the mainframe (as shown in the figure) with a screwdriver to remove the top cover. Then, unscrew the switch with a screwdriver and remove the switch.

Maintenance

Maintenance guarantees good performance. Please take good care of your appliance. Be sure to cut off the power supply before any maintenance operations (hold the plug and remove it). Perform maintenance operations with gloves to prevent cuts by sharp edges of the appliance. Remove oil stains on the surface of the strainer and mainframe regularly, and keep the appliance clean. Clean the strainer every month to ensure a good suction and exhaust performance. Perform total preventive maintenance every year to clean oil stains and guarantee good performance. Do not clean the appliance with water or a flammable cleaning agent.

Removal of Parts
Handle with care while disassembling parts to avoid distortion or damage.

(1) Hold the oil cup and pull it out horizontally.
(2) Remove the screws securing the strainer and remove the strainer.
(3) Remove the screws securing the external decorative cover (on the rear) and remove the decorative cover.
(4) Remove the screws securing the case cover and remove the case cover.
(5) Remove the screws securing the guide ring and remove the guide ring.
(6) Remove the wind wheel cap in the direction indicated by the arrow and remove the wind wheel.
(7) After maintenance operations, reinstall parts in the reverse order of removal.
Cleaning of Parts
(1) Please use neutral detergent, a soft cloth, and a soft brush for cleaning parts. Do not use organic solvents.
(2) Please soak parts for 30 minutes before cleaning. Avoid deformation or damage during cleaning. (3) Upon completion of part cleaning, rinse parts with fresh water and wipe dry with a soft cloth.
(4) Use a soft dry cloth or soft brush to clean the electrical parts, instead of water or detergent.
(5) If users do not clean the appliance according to the instructions, there may be a risk of fire.
Note: The range hood should be maintained by skilled personnel.

Troubleshooting

• Always remove the power plug before troubleshooting

Both the light and motor do not
work| The power plug is not properly connected| Connect the power plug properly
No power output| Ask an electrician for help
The motor works but the light is
not lit up| The light is damaged| Replace with a new light (Please contact our customer service center for door-to-door service)
The PC board is damaged| Replace with a new PC board (Please contact our customer service center for door-to-door service)
The light works but the AC motor
does not work| The capacitor has poor contact or is damaged| Please contact our customer service center for door-to-door service
The motor is damaged or the power board is damaged| Please contact our customer service center for door-to-door service
The running wind wheel is noisy| The wind wheel is loose and the cap is not tightened| Tighten the cap
Speed setting 1 is unavailable
Other speed settings are
available| The control switch is faulty| Replace with a new switch (Please contact our customer service center for door-to-door service)
Poor suction performance| Too high installation height| Reduce the installation height
Two windscreens are not completely opened| Check that windscreens should be flexibly rotated
Too large convection around the appliance| Close doors and windows if applicable
Too much oil stain| Clean oil stain
The maximum speed is not set| Set to the maximum speed
The DC motor does not work| The main power board does not communicate information to the motor| Replace with a new PC board (Please contact our customer service center for door-to-door service)

Warning:

1. Please cut off the power supply before connecting or replacing plug-ins.
2. A damaged power cable must be replaced by a skilled person from the manufacturer, its repair department, or other similar departments.
3. Do not suck the flame into the appliance. Otherwise, there may be a risk of fire.

Part Names

CONSUMER CARE CENTER

Thailand

Consumer Care Tel : (+66 2) 725 9000 Electrolux Thailand Co., Ltd. Electrolux Building 14th Floor 1910 New Phetchaburi Road, Bangkapi, Huai Khwang, Bangkok 10310 Office Tel : (+66 2) 7259100 Office Fax : (+66 2) 7259299
Email: customercarethai@electrolux.com

| Singapore
Consumer Care Center Tel: (+65) 6727 3699 Electrolux S.E.A. Pte Ltd.
351 Braddell Road

01-04, 351 On Braddell

Singapore 579713
Email: customer-care.sin@electrolux.com
---|---
Indonesia
Hotline service: 08041119999
PT. Electrolux Indonesia
Electrolux Building
JI.Abdul Muis No.34, Petojo Selatan, Gambir Jakarta Pusat 10160 Email:customercare@electrolux.co.id SMS & WA : 0812.8088.8863| Philippines
Consumer Care Center Toll-Free: 1-800-10-845-CARE(2273)
Consumer Care Hotline:(+63 2)845-CARE(2273) Electrolux Philippines,Inc.
Unit B 12F Cyber Sigma Bldg, Lawton Avenue, McKinley West, Taguig, Philippines 1634
Trunkline:+63 2 737-4757 Website:www.electrolux.com.ph Email:wecare@electrolux.com
Vietnam
Consumer Care Center Toll-Free
1800-58-88-99
Tel: (+84 28) 39105465
Electrolux Vietnam Ltd.
Unit 1&2, 1OF Sofic Tower, #10 Mai Chi Tho Street,
Thu Thiem Ward, Thu Duc City, Ho Chi Minh City, Vietnam| Malaysia
Consumer Care Center Tel: 1300-88-11-22 Electrolux Home Appliances Sdn. Bhd.
Corporate Office Address: Unit T2-7, 7th Floor, Tower 2, PJ33, No. 3, Jalan Semangat,
Seksyen 13,46200 Petaling Jaya, Selangor.
Office Tel : (+60 3) 7843 5999
Office Fax : (+60 3) 7955 5511
Consumer Care Center Address: Lot C6, No. 28, Jalan 15/22, Taman Perindustrian Tiong Nam, 40200 Shah Alam, SelangorConsumer Care Center Fax : (+60 3) 5524 2521
Email: malaysia.customercare@electrolux.com
HONG KONG
SERVICE HOTLINE: (+852) 3193 9888 DCH ELECTRICAL APPLIANCES SERVICE CENTRE
4/F, DCH BUILDING, 20 KAI CHEUNG ROAD,
KOWLOON BAY, HONG KONG
EMAIL: customercare@dch.com.hk WEBSITE: www.electrolux.com.hk

www.electrolux.com
The Thoughtful Design Innovator.
Do you remember the last time you opened a gift that made you say, “Oh! How did you know? That’s exactly what I wanted!” That’s the kind of feeling that we at Electrolux seek to evoke in everyone who chooses or uses one of our products. We devote time, knowledge, and a great deal of thought to anticipating and creating the kind of appliances that our customers really need and want.
This kind of thoughtful care means innovating with insight. Not design for design’s sake, but design for the user’s sake. For us, thoughtful design means making appliances easier to use and tasks more enjoyable to perform, freeing our customers to experience the ultimate 21st-century luxury: ease of mind. Our aim is to make this ease of mind more available to more people in more parts of their everyday lives, all over the world.
The “Thinking of you” promise from Electrolux goes beyond meeting the needs of today’s consumers. It also means we’re committed to making appliances safe for the environment—now and for future generations.
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com

Version No.: MU-H-202112

Documents / Resources

| Electrolux ECC9312K 90cm UltimateTaste 700 Chimney Extractor Hood [pdf] User Manual
ECC9312K, ECC9310S, ECC9232K, 90cm UltimateTaste 700 Chimney Extractor Hood, ECC9312K 90cm UltimateTaste 700 Chimney Extractor Hood, UltimateTaste 700 Chimney Extractor Hood, Chimney Extractor Hood, Extractor Hood
---|---
| Electrolux ECC9312K 90cm UltimateTaste 700 Chimney Extractor Hood [pdf] User Manual
ECC9312K, ECC9310K, 90cm UltimateTaste 700 Chimney Extractor Hood, Chimney Extractor Hood, Extractor Hood, 90cm UltimateTaste 700, Hood

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>