supla DIW-01 Wi-Fi Light Dimmer User Manual
- June 10, 2024
- Supla
Table of Contents
supla DIW-01 Wi-Fi Light Dimmer
BEFORE GETTING STARTED
DEVICE FEATURES
- universal dimmer for 230 V AC lighting,
- maximum load power up to 150 W,
- full regulation of operating parameters.
WHAT’S INSIDE THE BOX
- DIW-01 device
- user’s manual
WHAT YOU NEED TO GET STARTED:
- screwdriver / pliers,
- max. 2.5 mm2 cable for connecting the power supply,
- qualification certificate for voltages up to 1 kV is recommended.
WARNING
The device must be connected to power supply in accordance with applicable
electrical and safety standards or regulations. See this User Manual for the
wiring instructions. Installation, wiring and setting of this product shall
only be done by qualified electrical engineers who have read and understood
this User Manual and the product features.
Do not open or otherwise disassemble the product enclosure; otherwise the
product warranty will be void and an electrocution hazard may occur. Prior to
installing and wiring this product, make sure that the wiring to be connected
is not live. The conditions and methods of transport, storage and operation of
this product may affect its performance. Do not install the product if any of
its components is missing, the product is damaged or deformed in any way. If
any malfunctions are found, consult the manufacturer.
ZAMEL Sp. z o.o. hereby declares that the type of DIW-01 radio device complies with Directive 2014/53/EU. The entire EU declaration of conformity is available at: www.zamel.com
INFORMATION
During installation, make sure that the receiver is not exposed to direct contact with water and that it does not operate in a humid environment. The installation place temperature should be within the range of -10 and +55°C.
The DIW-01 receiver is designed for indoor installation. When installed outdoors, the device should be placed in an additional enclosure of hermetic type and protected against water penetration – in particular where connection terminals are located.
TECHNICAL DATA
DIW-01
Rated voltage:| 230 V AC
Rated frequency:| 50 / 60 Hz
Rated power consumption:| 0.7 W
Transmission:| 2.4 GHz Wi-Fi b/g/n
Operation range:| Wi-Fi network range
Maximum transmit power:| ERP < 20 mW
Number of inputs:| 1
Cooperation with switches:| monostable (buttons) and bistable (brightness
adjustment is then done in the application).
Number of output channels:| 1
Number of terminals connection terminals:| 4 (wires of cross-section cross-
section up to 2.5 mm²)
Housing fixing:| Ø 60 mm installation box
Working temperature range:| -10 ÷ +55°C
Case protection class:| IP20
Dimensions:| 47.5 x 47.5 x 23 mm
Weight:| 0.04 kg
Maximum output load capacity:| 150 W for R loads / 100 VA for RC and RL loads
GETTING STARTED IN 5 STEPS
LET’S GET STARTED
download, install and launch the supla mobile app
STEP 1 install the app
INSTALL THE SUPLA MOBILE APP
STEP 2 create an account / log in
CREATING A SUPLA ACCOUNT
IF YOU DO NOT HAVE AN ACCOUNT
Create it by tapping “Create Account” in your app.
IF YOU ALREADY HAVE AN ACCOUNT
Enter the e-mail address which you have used to create the account.
CREATE AN ACCOUNT
On this page, enter the following data:
- e-mail address,
- password,
- password confirmation.
Confirm all information by tapping “Create an account”.
STEP 3 connect to the power supply
WIRING DIAGRAM
Connect the DIW-01 device to the installation according to the following diagram.
STEP 4 add the device
ADDING THE DEVICE AUTOMATICALLY
OPEN THE APP
Then select “Add device” from the menu.
STARTING THE WIZARD
The Add Device Wizard will appear. To continue, press the “Next” button.
NETWORK PASSWORD
Choose a WiFi network to enable Internet connectivity for the device. Enter
the network password and tap “Next” to continue.
CONNECTING THE DEVICE
Wire the power supply to the device as shown in the diagram. Make sure that
the device STATUS LED responds as shown in the animation on screen. If it does
not, switch the device into the configuration mode by holding the CONFIG
button on the device. Next, press the START button.
NEW DEVICE REGISTRATION DISABLED
If the “New Device Registration Disabled” message is displayed, open this
website:
Log into your account, go to the “My SUPLA” tab and Enable Device Registration. Next, repeat the device adding process.
DEVICE ADDED SUCCESSFULLY
Adding a device is simple and should end without any problems. If the device
is added successfully, the following message is displayed: “Device
configuration successful”. Tap OK. Now, the supla app should display the
device which you have just added on the list. The DIW-01 STATUS LED in the
front goes on steadily when the connection with the server is active.
CAUTION!
If the connected device is not shown on the list immediately once the
configuration is complete, check the device STATUS LED. When added for the
first time, the STATUS LED of some devices may flash very fast and
irregularly. This happens when the device controller is updating its firmware.
A moment after the update, the STATUS LED should go on steadily which means
there is an active connection with the server.
ADDING THE DEVICE MANUALLY
Add the device manually when the automatic device adding mode of the supla app
fails somehow.
CONFIGURING THE DEVICE
Now, find the device in the available Wi-Fi network list on your mobile device
and connect to it. The Wi-Fi network name should begin with “ZAMEL-DIW-01”,
followed by the device serial number.
DEVICE CONFIGURATION
MODE To do this, switch the device into the configuration mode by pressing and
holding the CONFIG button until the STATUS LED starts to flash.
Open a web browser and type the following address in the address bar:
192.168.4.1 and open it.
The configuration page will be displayed. Here, you can easily change the
network settings.
When done, tap “SAVE” at the bottom of the screen. The message “Data saved!” should be displayed. To confirm the entered data, briefly press the CONFIG button on the device. If the device connects to the server successfully, the STATUS LED will go on steadily
STEP 5 control the lights
APP FUNCTIONS
SETTING PARAMETERS
RESETTING THE DEVICE
RESETTING THE DEVICE TO DEFAULT SETTINGS
-
Press and hold CONFIG
The STATUS LED should flash fast. -
Release the CONFIG button
The STATUS LED will continue to flash. -
Press and hold CONFIG again
The STATUS LED should blink once. -
Release the CONFIG button
The device has been reset to defaults and restarts now.
The STATUS LED should flash fast.
MORE INFORMATION
Additional information and video material You can find by scanning QR code or by using the following link:
https://supla.zamel.com/en/product/diw-01/
WARRANTY
-
ZAMEL Sp. z o.o. grants a 24-month warranty for the products it sells.
-
The warranty granted by ZAMEL Sp. z o.o. does not cover:
(a) defects caused by transport, handling or other factors;
(b) defects caused by improper installation or operation of the products manufactured ZAMEL Sp. z o.o.;
(c) defects caused by any modifications or alterations made by the BUYER or any third party to the sold products or to the equipment required for the proper operation of the sold products;
(d) defects caused by any force majeure event or another fortuitous event beyond any reasonable control of ZAMEL Sp. z o.o. -
The BUYER shall report all warranty claims in writing at the point of sale or to ZAMEL Sp. z o.o.
-
ZAMEL Sp. z o.o. will examine each warranty claim as regulated by the applicable provisions of the Polish law.
-
If found valid by examination, the warranty claim will be processed by replacement of the defective product, its repair or a refund of the price of purchase at the sole discretion of ZAMEL Sp. z o.o.
-
No rights of the BUYER arising from the statutory or regulatory laws concerning implied warranty for defects of sold goods are limited, prejudiced or excluded by this warranty
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>