boAt Airdopes 141 Pro True Wireless User Guide
- June 10, 2024
- Boat
Table of Contents
boAt Airdopes 141 Pro True Wireless
SOUND THAT MATTERS
Charging the Case
Step : To charge the case. plug one end of the provided cable into the case and connect the other end to a computer/ wall adapter/powerbank, etc During charging, the red LED continuously blinks. Once the case gets fully charged, the LED indicator turns into solid red.
Remaining Low Case Battery LED Indication
White LED blinks three times to denote low case battery, whenever the case lid
gets opened/closed.
Case LED Indication when Earbuds are getting charged from the case
This is to indicate that the earbuds are getting charged from the case (when case lid gets closed):
- White LED turns solid
- White LED stays off when earbuds are fully charged
Basic Functions
- Voice Assistant: Long touch the left CTC for 3 seconds to activate default voice assistant
- Answer: Single tap the CTC on either earbud to answer an incoming call
- Hang Up/ Reject Cal: Double tap the CTC.on either earbud to end / reject call Play/Pause Music: Single tap either earbud’s CTC to play or pause music
- Next Track: When playing music, doubie tap the right earbud’s CTC to skip to the next song
- Previous Track When playing music, double tap the left earbud’s CTC to return to the previous song Note: Volume can only be controlled via the media device.
AIRDOPES 141 PRO
Get ready to immerse yourself in musical bliss with your very own pair of boAt Airdopes 141 Pro. Please consider this manual as your guiding map towards the unparalleled shores of auditory realm. Knowledge of Bluetooth and device connectivity is essential for steering this boat and therefore we strongly recommend thorough reading of this manual. Also, you may refer to the same at times when you face any sort of difficulty.
Voice Assistant
Step 1: Long touch the CTC on left earbud for 3 .seconds to activate
default smnrt voice assistant
Step 2: The respective voice assistant screen pops up and you may place
your commands at ease
Tips: You may try out the following commands,
Note: If the voice assistant doesn’t get triggered, then the functionality Ms to be first enabled via y<XJr media device settings,
BEAST Mode
Long touch the right CTC for 3 seconds to switch to Low Latency mode, also known as the BEAST Mode. Once switched on, it gets notified via a sound prompt. Long touch the right CTC for 3 seconds once again, to turn it off and return to Music Mode. Made for the Gamers-By Gamers, BEAST Mode reduces the latency significantly and improves the overall gaming experience
ENx Mode
Our ENx” tech algorithm cancels out the background noise so that you can be heard crystal clear via voice calls. One need not activate ENx as the mic is equipped with the same and activated by default. Deliver your yoice without interruotions anywhere traffic, railway stations, airports, work spacey iteraiy anywnere.
Package Contains
- lx Pair of TWS Earbuds
- lx Warranty Card
- lx Charging Cas
- 1x Catalogue
- lx Type
- C Ch,arging Cable
- lx Read Me Card
- lx User Manual
- 1x FAQ Card
Power On (First Time User)
Step 1: To switch the earbuds on (Srnart Power On) simply open the lid of
the charging case (when carbuds are inside). Courtesy our IWP~”-( lnsta Wake
N’ Pair) technology, the earbuds power on automatically, get connected and ent
er the connection modo
OR
Long touch the CTC (Capacitive Touch Control) on both earbuds for 3 seconds to
manually power on the earbuds Step 2: After powering on, the earbuds enter
the Connection Mode, indicated by- alterMte red and blue LED flashes on
ptlmary earbud and blue LEO flashes once every 5 seconds on the secondary
earbu.d
Smart Power Off
Step 1: After usage, remove both the earbuds from your ears
Step 2: Place the earbuds back into the chllrging case in correct
orientation and close the lid
The earbuds automatically switch off (and enl er charging mode).
Manual Power Off
Step 1: Long touch both CTCs for 5 seconds to manually power oft the
earbuds
Step 2: Once the earbuds get turned off, place them back inside the
cas.e and close the lld
Factory Reset
Perform the factory reset” In case you feel any difficulty while operating
your Alrdopes,
“NOTE: Before performing reset, clear “Alrdopes 141 Pro” from p:,irlng
device history by forgetting dev;ce
Step 1: Place both the e-arbuds inside the care In correct orle-ntt1tion
c’)nd let the case lid remain open
Step 2: Long press the Reset button on the ca:s.e for s se<:onds to
perform reset
Slep 3: The case LED flashes 5 t imes co indicate a successful factory
reset
Step 4: Take out the earbuds from the case and perform a fresh connection
Connection Mode
Step 3: Turn on the 8 bIuetooth functionality on your phone/media device
and scan
Step 4: Search for ‘Airdodes 141 Pro’ and pair accordingly
CongraitulatloM! Your earbuds afe now connected successfully vla Bluetooth.
Note:
- Pairing mode JtJsts lor 5 minutes. If the pbirJng time Is missed, then you wlll need to reconnect the earbuds dnd follow the dbove-menrioned procedure
- Alrdopes 141 Pro remembers previously connected devfces; once switched on, the wrbuds automatical(y reconnect to the previously connected devices in working l’bnge
Single Earbud Usage
Step 1: Please note that both the earbuds can be used in mono rnode. Use
Smart / Manual Power On for switching on the desired earbud
Step 2; The selected earbud automatically enters the connection mode
Indicated by red and blue LED flashes
Step 3: Turn on Sluetooth on your phone/media device and search tor
‘Airdopes 141 Pto’ to connect
Notes:
- To switch to Stereo mode. simply take our-the other earbud from the C/JSe. Jr will automatiCdlly power on and l)iJir with the previously selected earbud. hence enabling Stereo us,)ge
Congratulations! Your Airdopes 141 Pro has been Reset
SPECIFICATION
You cannot skip tracks or return to the previous tracks in Mono (single- earbuo) mode
Quick Guide on Functionalities
Charging the Earbuds
Step 1: Please insert the earbuds back inside the charging case in
correct orientation and close the lid
Step 2: During charging, the LED indicator stays solid red
Step 2: Once the earbuds get fully charged, the charging case
automatically switches off to save power and the LED turns off
Note
- When the earbuds remaining battery is below 2O%, Red LED blinks 3 times every 30 seconds
- Before using the earbuds for the first time, it is recommended to fully charge the earbuds. Also, please keep the lid of the charging case closed while charging
Warning
- Please follow t he instructions to operate
- Please don’t use the earbuds In extreme temperatures
- Please don’t use the product near water
- Please keep the product away from heat sources, as the heat may damage it
- Don’t Jam t he ports such as cha(ger port. LED port. etc,
- It is recommended to utilize the product be.low the maximum volume In order to protect hearing and extend the ear•buds’ service life