RYOBI RB360GLL 360 Degree Green Line Laser Level User Manual

RYOBI RB360GLL 360 Degree Green Line Laser Level

Product Information

The RB360GLL and RB360RLL are laser-level products designed for determining and verifying horizontal and vertical lines indoors.
They are equipped with a Class 2 laser, which means that caution must be taken to avoid direct eye exposure, as this can cause severe eye injury.
The product should not be used for any other purpose than its intended use.

Laser Safety Warnings

• Do not stare into the laser beam.
• Avoid direct eye exposure.
• Do not direct the laser beam toward other people.
• Avoid using the product on reflective surfaces as the laser beam may reflect at the operator or other persons.
• When the product is brought into a warm environment from a cold one or vice versa, allow it to come to the surrounding temperature before use.
• Store the product indoors and avoid substantial knocks, continuous vibration, or extreme temperatures.
• Always keep the product away from dust, liquids, and high humidity as they may damage internal components or affect accuracy.
• If laser beam hits your eye, you must close your eyes and immediately turn your head away from the beam.
• Do not position the laser beam so that it unintentionally blinds you or others.
• Do not look into a laser beam using magnifying optical devices such as binoculars or a telescope as this will increase the level of eye injury.
• If you use laser goggles to enhance the visibility of the laser beam, note that they will not protect your eyes against laser radiation.
• Do not remove or deface warning labels on the product.

Intended Use

The RB360GLL and RB360RLL are intended for indoor use only and should not be used for any other purpose. The laser level products are designed for determining and verifying horizontal and vertical lines.

Product Usage Instructions

Before assembling, maintaining, or operating the product, it is essential to read the instructions provided in the user manual. The RB360GLL and RB360RLL should only be used for indoor operations to avoid hazardous situations. Avoid using the product on reflective surfaces, as the laser beam may be reflected at the operator or other persons. When bringing the product into a warm environment from a cold one, or vice versa, allow it to come to the surrounding temperature before use. Store the product indoors and avoid substantial knocks, continuous vibration, or extreme temperatures. Always keep the product away from dust, liquids, and high humidity as they may damage internal components or affect accuracy. In case the laser beam hits your eye, close your eyes immediately and turn your head away from the beam. Do not position the laser beam so that it unintentionally blinds you or others. Do not look into a laser beam using magnifying optical devices such as binoculars or a telescope as this will increase the level of eye injury. The RB360GLL and RB360RLL are designed to determine and verify horizontal and vertical lines indoors. Be sure to follow the instructions provided in the user manual for proper assembly, maintenance, and operation of the product.

Important! You must read the instructions in this manual before assembling, maintaining and operating the product.
Safety, performance, and dependability have been given top priority in the design of your 360° line laser.

INTENDED USE

• The 360° line laser is intended to be used only by adults who have read and understood the instructions and warnings in this manual, and can be considered responsible for their actions.
• The product is intended for determining and verifying horizontal and vertical lines.
• The product is intended for indoor use only.
• Do not use the product for any other purpose. Use of the product for operations different from intended could result in a hazardous situation.

LASER SAFETY WARNINGS

• Laser radiation. Do not stare into beam. Class 2 laser product.
• Risk of severe eye injury if the laser beam is directed at persons or animals. Avoid direct eye exposure.
• Do not direct the laser beamtowards other people.
• Do not operate the product around children or allow children to operate the laser.
• Avoid using the product on reflective surfaces. The laser beam may be reflected at the operator or other persons.
• When the product is brought into a warm environment from a cold one, or vice versa, allow it to come to the surrounding temperature before use.
• Store the product indoors and avoid substantial knocks, continuous vibration or extreme temperatures.
• Always keep the product away from dust, liquids and high humidity. They may damage internal components or affect accuracy.
• If laser beam hits your eye, you must close your eyes and immediately turn your head away from the beam.
• Do not position the laser beam so that it unintentionally blinds you or others.
• Do not look into a laser beam using magnifying optical devices such as binoculars or a telescope. This will increase the level of eye injury.
• If you use laser goggles to enhance the visibility of the laser beam, note that they will not protect your eyes against laser radiation.
• Do not remove or deface warning labels on the product.
• Do not disassemble the product.
• Avoid heavy impact to or dropping of the laser. The accuracy of the laser should be checked before use if it has been dropped or subjected to other mechanical stresses.
• Do not operate the product in explosive areas or in extreme environments.
• When not in use, make sure to turn off the power, and place the laser in its carrying pouch.
• Make sure the on/off switch is in the off position before transporting the laser.
• NOTE: If the on/off switch is not in the off position before transportation, internal mechanical damage may occur.
• If the product is not in use for a long period of time, remove the batteries from the battery compartment. This will prevent batteries from leaking and corrosion.

KNOW YOUR PRODUCT

1. Vertical laser beam window
2. 360° horizontal laser beam window
3. Self-levelling LED indicator
4. Mode selector
5. Battery door
6. ON/OFF switch
7. Mounting screw hole(1/4”)
8. Battery
9. Storage pouch
10. Operator’s manual

SELF-LEVELLING LED INDICATOR

LED

indicator

| Explanation
Green| Self-leveling is complete.
Red| Self-leveling is not successful; the laser line blinks. Place the product in a horizontal position of +/-4°.

MAINTENANCE

• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
• For greater safety and reliability, all repairs should be performed by an authorised service centre.

SYMBOLS ON THE PRODUCT

• Safety alert

• Volts

• Direct current

• European Conformity

• Mark

• British Conformity Mark

• Ukraine Conformity Mark

• Eurasian Conformity Mark

• Read the instructions carefully before using the product.

• Class 2 laser beam. Do not stare into the laser beam.

• Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

SYMBOLS IN THIS MANUAL

• Note
• Parts or accessories sold separately
• Do not stare into the laser beam.

PRODUCT SPECIFICATIONS

BATTERY INSTALLATION

MODES

RYOBI WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

1. The warranty period is 24 months for consumers and commences on the date the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.
2. There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu-website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newly-acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
3. The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
   • any damage to the product that is the result of improper or lack of maintenance
   • any product that has been altered or modified
   • any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
   • any damage caused by non-observance of the instruction manual
   • any product not displaying the CE approval mark on the rating plate
   • any product that has been attempted to be repaired by a non-authorised warranty service centre or without prior authorisation by Techtronic Industries
   • any product connected to improper power supply (amps, voltage, frequency)
   • any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
   • normal wear and tear spare parts
   • inappropriate use, overloading of the tool
   • use of non-approved accessories or parts
   • Power tool accessories provided with the tool or purchased separately, including but not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide, etc.
   • Components (parts and accessories) subject to natural wear and tear, including but not limited to service & maintenance kits, carbon brushes, bearings, chuck, SDS drill bit attachment or reception, power cord, auxiliary handle, transport carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact wrench pins & springs, etc.
4. For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
5. A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected
6. This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey, Russia, and the United Kingdom. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRE

Any request or issue with the product can be addressed to your local authorised service centres (visit www.Ryobi-tools.eu) or directly to: Techtronic Industries GmbH, Max Eyth Straße 10, 71364 Winnenden, Germany. Please state the serial number and product type printed on the label.

RYOBI is a trade mark of Ryobi Limited, and is used under license.

• Techtronic Industries GmbH
• Max-Eyth-Straße 10,
• 71364 Winnenden, Germany
• Techtronic Industries (UK) Ltd
• Parkway
• Marlow, Bucks
• SL7 1YL
• UK
• 20211118v1

References

• Ryobi Tools
• Ryobi Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>