EZYmount SLT-910 Tilting TV Wall Mount Installation Guide
- June 10, 2024
- EZYmount
Table of Contents
EZY mount SLT-910 Tilting TV Wall Mount
The SLT-910 Tilting Wall Mount is designed to securely mount your TV onto a wall. It has a maximum weight capacity of 70kg and can accommodate TV sizes up to 80 inches. The wall mount can be adjusted to the desired angle using the tilt adjusting knobs.
Product Installation
Before starting the installation, make sure to read the entire instruction
manual and ensure that all components are included. It is recommended that the
installation be carried out by someone with good mechanical ability and basic
building experience who understands the manual. If mounting on a timber wall
stud, use a stud finder to locate
the centre of the stud and make sure to anchor the mounting screws into it. If
mounting on a solid brick or concrete block, do not drill into mortar joints
and make sure to mount in a solid part of the block. Always make sure that the
supporting surface (wall) will safely support the combined load of the bracket
and all attached hardware and components. Tighten screws firmly but not over-
tighten.
Maintenance
It is important to check the bracket’s security and safety at regular intervals, at least every three months. If there are any questions regarding the product or usage, contact your local distributor.
CAUTION: Do not exceed the maximum weight capacity as serious injury or
property damage may occur.
WARNING: Do not commence installation until you have read and understood
the instructions and warnings contained in this installation sheet. Improper
installation or use of this product may cause damage or serious injury. This
product is intended for indoor use only.
CAUTION: DO NOT EXCEED THE MAXIMUM STATED WEIGHT CAPACITY. SERIOUS INJURY
OR PROPERTY DAMAGE MAY OCCUR!
NOTE: Please read the entire instruction manual before you start
installation and assembly
WARNING
- Do not commence installation until you have read and understood the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your place of purchase.
- This mounting bracket was designed to be installed and utilized ONLY as specified in this manual. Improper installation or use of this product may cause damage or serious injury.
- This product should only be installed by someone of good mechanical ability, with basic building experience and full understanding of this manual.
- Make sure that the supporting surface (i.e. wall) will safely support the combined load of this bracket and all attached hardware (TV) and components.
- If mounting to timber wall studs, make sure that the mounting screws are anchored into the centre of the studs. Use of a stud finder is highly recommended.
- Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
- Tighten screws firmly, but do not over tighten. Over tightening can cause damage, greatly reducing their holding power.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the
component checklist prior to installation. If any parts are missing or faulty,
contact your local distributor for assistance.
Package M
Package W
Mounting on Timber Stud Walls
WARNING
- Make sure that mounting screws are anchored into the centre of the studs. Use of a stud finder is highly recommended.
- Installers are responsible to provide hardware for other types of mounting situations.
- The installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware (TV) and components.
Mounting on Solid Brick and Concrete Block
WARNING
- When installing wall mounts on cinder block, verify the actual concrete thickness is at least 35mm for using the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 25mm minimum from the side of the block. It is suggested to use the electric drill on a slow setting to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
- The installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware (TV) and components.
Attach Adapter Brackets
- Position the adapter brackets as close as possible to the middle of the screen.
- Ensure the Tilt Adjusting Knobs are located on the outside of the rails.
- Screw the adapter brackets onto the TV.
- Tighten all screws, but do not over tighten.
Hang TV on the Wall Plate
Hook
the TV onto the upper ridge of the wall plate. Tighten the safety screws using
a Phillips screwdriver to secure the TV to the lower ridge of the wall plate.
Important: Make sure the TV is correctly hooked onto the wall plate and
the safety screws are locked safely before releasing the TV.
Adjustment
Use the
tilt adjusting knobs to adjust your TV to the desired angle.
Maintenance
- Check that the bracket is secure and safe to use at regular intervals (at least every three months)
- Please contact your local distributor if you have any questions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>