NOBLE FLAME Vegas with Touchpanel Electric Wall Mounted Fireplace Owner’s Manual

: June 9, 2024
: NOBLE FLAME

NOBLE FLAME Vegas with Touchpanel Electric Wall Mounted Fireplace

NOBLE-FLAME-Vegas-with-Touchpanel-Electric-Wall-Mounted-Fireplace-
PRODUCT

Product Information

The Vegas Electric Wall Mounted Fireplace by Noble Flame is a modern and sleek heater that can be mounted on a wall. It operates on AC 220-240V 50HZ with a power output range of 1400W-1600W. The heater is available in various models with different sizes ranging from 770mm to 2410mm. The heater has a touch panel that allows you to easily control its settings.

Product Usage Instructions

Before using the Vegas Electric Wall mounted Fireplace, it is essential to read and understand the entire owner’s manual, including all the safety information. Failure to do so could result in fire, electric shock, or serious personal injury.

Here are some important usage instructions:

To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater.
Keep combustible materials like furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) away from the front of the heater and also from its sides and rear.
Extreme caution is necessary when children or invalids are near the heater or when it is left operating and unattended.
Do not operate the heater with a damaged cord or plug or after the heater malfunctions or has been damaged in any manner. Discard the heater or return it to an authorized service facility for examination and/or repair.
Do not run the power cord under carpeting or cover it with throw rugs, runners, or similar coverings. Also, do not route the power cord under furniture or appliances. Arrange the power cord away from traffic areas and where it will not be tripped over.
Connect the heater to properly grounded outlets ONLY.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause electric shock, fire, or damage to the heater.
To prevent a possible fire, do not block air intakes or exhaust in any manner. Doing so could cause a fire. Do not use on soft surfaces like a bed, where openings may become blocked.
Avoid using the heater in areas where gasoline, paint, or flammable liquids are used or stored.
Plug heaters directly into a wall outlet/receptacle. Never use them with an extension cord or relocatable power tap (outlet/power strip).
Never place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater.
Never use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp, or come in contact with water.
Regularly inspect all air vents to make sure they are free from dust, lint, or other blockages. Unplug the unit and clean with a vacuum ONLY. Do not rinse or get wet.
Never hang this unit on a wall directly below an electrical outlet. Also, never permanently install it in a recessed area of the wall. This may result in blocked airflow, overheating, or fire.

Always use the heater as described in the manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. Enjoy your Vegas Electric Wallmounted Fireplace by Noble Flame responsibly and safely!

MODEL

770
900
1070
1220
1380
1530
1830
2410

CAUTION

Read and understand this entire owner‘s manual, including all safety information, BEFORE plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury.
Keep this owner‘s manual for future reference. If you sell or give this product away, make sure this manual accompanies this product.

IMPORTANT SAFET Y INFORMATION!

SAVE THESE INSTRUCTIONS!

Read all instructions before using this heater

CAUTION

This heater is hot when in use.
To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater or return to authorized service facility for examination and/or repair.
DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs, runners, or similar coverings. DO NOT route power cord under furniture or appliances. Arrange power cord away from traffic area, and where it will not be tripped over.
Connect to properly grounded outlets ONLY.
DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause electric shock or fire, or damage the heater.
To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. Doing so could cause a fire. DO NOT use on soft surfaces, like a bed, where openings may becomeblocked.
A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored.
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap (outlet/power strip).
DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater.
NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp, or come in contact with water.

CAUTION

AVOID FIRE!
Regularly inspect all air vents to make sure they are free from dust, lint, or other blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
NEVER hang this unit on a wall directly below an electrical outlet.
NEVER permanently install in a recessed area of the wall. This may result in blocked air flow, overheating, or fire.
ALWAYS mount to wall bracket before use. DO NOT set on the floor, or another surface, touse.
NEVER use a wall mount bracket from another manufacturer

CAUTION

INDOOR use only! NEVER use this heater outdoors! Doing so may result in electricshock!
This product is not intended to be a primary heat source. It is for supplemental heat only.

CAUTION

Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
NEVER modify this heater. Doing so could result in personal injury or property damage. Mo- dification of this fireplace completely voids allwarranties.
ALWAYS turn this heater off before unplugging it from the outlet.
ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace.
NEVER leave this heater unattended. ALWAYS unplug this heater when not inuse.
ALWAYS store this heater in a dry location. NEVER use the fireplace if it has becomewet.
Place the heater near a wall outlet so an extension cord is not needed. If an extension cord is needed, the gauge of the cord must be at least 14AWG, and the rating must be at least 1875 Watts. NEVER use a smaller gauge cord with a lower rating. Doing so may result in fire or electric shock.
ONLY use this heater on a 220V AC 15-Amp grounded circuit. NEVER overload the circuit. If this heater trips the circuit breaker, unplug all other appliances on the same circuit before the next use. Avoid plugging other appliances into the same circuit as thisheater.
NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections. Plugging this heater into a faulty outlet could result in electric arcing within the outlet that could cause the outlet to overheat or catch fire.
ALWAYS check your heater cord and plug connections with each use!
MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs can cause the outlet to overheat.
- Heaters draw more current than small appliances. Overheating may occur even if it has not occurred with the use of other appliances.
- During use check frequently to see if the plug outlet or face plate is HOT!
- If the outlet or face plate is HOT, discontinue use immediately and have a qualified electrician inspect and/or replace the faulty outlets.

PREPARATION

CAUTION

This product includes a GLASS panel! Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage
Remove all parts and hardware from the carton and place them on a clean, soft, dry sur- face. Parts and assembly steps are grouped for wall-hanging use. Check the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible.
You will need the following tools (not included):
- screwdriver
- stud finder
- level
- tape measure ʁ electric drill
- 1/4” wood drill bit ʁ hammer

PARTS & HARDWARE

NOBLE-FLAME-Vegas-with-Touchpanel-Electric-Wall-Mounted-Fireplace-
FIG-1

SPECIFICATION & DIMENSIONS

NOBLE-FLAME-Vegas-with-Touchpanel-Electric-Wall-Mounted-Fireplace-
FIG-2

MODEL	A	B	C	D	E	F	G

VEGAS 770

| ****

778mm

| ****

428.6mm

| ****

122.3mm

| ****

609mm

| ****

396mm

| ****

220mm

| ****

570mm

| 30.7”| 16.9”| 4.8”| 24”| 15.6”| 8.7”| 22.4”
VEGAS 990| 900mm| 508mm| 120mm| 720mm| 450mm| 255mm| 654mm
| 35.4”| 20”| 4.7”| 28.3”| 17.8”| 10”| 25.8”
VEGAS 1070| 1067mm| 508mm| 120mm| 871.8mm| 450mm| 255mm| 813.8mm
| 42”| 20”| 4.7”| 34.3”| 17.8”| 10”| 32”
VEGAS 1220| 1220mm| 508mm| 120mm| 1075mm| 450mm| 255mm| 967mm
| 48”| 20”| 4.7”| 42.3”| 17.8”| 10”| 38.1”
VEGAS 1380| 1372mm| 508mm| 120mm| 1177mm| 450mm| 255mm| 1119mm
| 54”| 20”| 4.7”| 46.3”| 17.8”| 10”| 44.1”
VEGAS 1530| 1524mm| 508mm| 120mm| 1329mm| 450mm| 255mm| 1271mm
| 60”| 20”| 4.7”| 52.3”| 17.8”| 10”| 50”
VEGAS 1830| 1828mm| 508mm| 120mm| 1633.8mm| 450mm| 255mm| 1575mm
| 72”| 20”| 4.7”| 64.3”| 17.8”| 10”| 62”
VEGAS 2410| 2413mm| 508mm| 120mm| 2218mm| 450mm| 255mm| 2160mm
| 95”| 20”| 4.7”| 87.3”| 17.8”| 10”| 85”

INSTALLATION & ASSEMBLY

INSTALLATION

CAUTION

It’s required that TWO CAPABLE ADULTS to perform this installation.

NOTICE

The wall mount fasteners included with this fireplace are for use ONLY with a wood-framed wall covered in drywall (sheet rock). For concrete walls, cinder blocks, or other wall types, consult a professional for the best attachment methods.

STEP 1

Find a safe location.
Minimum clearance on each side: 19.7” (50 cm)
Minimum clearance below: 19.7” (50 cm)
Minimum clearance above: 39.4” (100 cm)
Minimum clearance from the front and sides: 19.7” (50 cm)
Choose a location near an outlet so an extension cord is not required.
DO NOT position the unit directly below a power outlet.
See Safety Information on pages 2 and 3 for warnings about safe placement, safe installation, and proper use of this product.

STEP 1

Use a 8 drill bit to drill the holes and use the Hammer to thread the Drywall anchors (C) into the hole till it keep flat with the wall.

STEP2

Using the wood screws (B) to fix the wall bracket, with wood screws thread thewall bracket and to lock with the drywall anchors, please tighten all wood screws.

STEP3

Have two people lift the fireplace machine up and insert the slots (2 slots on back of fireplace box) to the wall bracket hooks.

STEP4

After having installed the fireplace safely, then using screwdriver to lock the bracket and fireplace with two ST4x8 (D) screws in both sides. Check the appliance for stability ensuring that the appliance will not pull free from the wall.

CAU T I O N

This next step involves GLASS! ALWAYS use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.
ALWAYS keep the decorative crystals OUT OF REACH OF CHILDREN! Leave no pieces where children can find them. Failure to do so could cause a choking hazard.

NOTICE

To place to decorative crystals, follow these steps. Have a capable adult help you.

STEP5

While one person holds the glass panel, remove the two screws at the top edge of the fireplace with a Phillips (+) screwdriver.
Together, carefully remove the front glass panel and set it aside on a clean soft surface.
Arrange the decorative crystals/pebbles (F/G) on the shelf by using the plastic tray in the desired position.
Set the front glass panel back onto the firebox.
Align the tabs of the glass panel with the holes on the top edge of the fireplace. Thread the screws back into the holes and tighten them both with a screwdriver.

OPERATION

CAUTION

Read and understand this entire owner’s manual, including all safety information, BEFORE plugging in or using this product. Failure to do so could result in electric shock, fire, serious injury, or death.

POWER

Plug the power cord into a 220 Volt 15 Amp grounded outlet (see IMPORTANT SAFETY INFORMATION on Pages 2 and 3).
Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit.
DO NOT plug other appliances into the same circuit.

NOTICE

When the heater is first turned on, a slight odor may be present. This is normal and should not occur again unless the heater is not used for a long period of time.
To improve operation, aim the remote control at the front of the fireplace. DO NOT press the buttons too quickly. Give the unit time to respond to each command.

METHODS OF OPERATION

This electric fireplace can be operated by the TOUCH PANEL located on the right down area of front glass panel (see figure below), or by the battery- powered REMOTE CONTROL. The operation and functions of methods are the same.
Before operating, please review the IMPORTANT SAFETY INFORMATION on Pages 2 and 3 and heed all warnings.

HOTEL – MODE

By using this mode, your individual settings for the following functions will be retained not only after you turn off the power on the touch panel or remote control, but also when you disconnect the power:
- Flame color
- Flame brightness
- Backlight Color
- The settings for heating, temperature and timer are not saved and are automatically reset to default after power off.

REMOTE CONTROL

NOBLE-FLAME-Vegas-with-Touchpanel-Electric-Wall-Mounted-Fireplace-
FIG-10 NOBLE-FLAME-
Vegas-with-Touchpanel-Electric-Wall-Mounted-Fireplace-
FIG-11

TEMPERATURE LIMITING CONTROL

This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafetemperature, the heater will automatically turn OFF.

TO RESET

Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes.
Unplug the power cord from the outlet.
Inspect the fireplace to make sure no vents are blocked or clogged with dust or lint. If they are, use a vacuum to clean the vent areas.
If the problem continues, have your outlet and wiring inspected by a professional.

REMOTE CONTROL BATTERY INFORMATION

Remote control uses one CR2025 battery (Included).
Instructions for battery installation are on the Remote Control batterycompartment.

CAUTION

NEVER dispose of batteries in fire. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center.

CARE & MAINTENANCE

CLEANING

CAUTION

ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury.
NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury.

METAL

Buff using a soft cloth, slightly dampened with a citrus oil-based product.
DO NOT use brass polish or household cleaners as these products will damage the metal trim.

GLASS

Use a good quality glass cleaner sprayed onto the cloth or towel. Dry thoroughly with a paper towel or lintfree cloth.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

VENTS

Use a vacuum or duster to remove dust and dirt from the heater and vent areas.

PLASTIC

Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water. ʁ NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

MAINTENANCE

CAUTION

Risk of electric shock! DO NOT OPEN any panels ! No user-serviceable parts inside!
ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury.

ELECTRICAL AND MOVING PARTS

The fan motors are lubricated at the factory and will not require lubrication.
Electrical components are integrated in the fireplace and are not serviceable by the con- sumer.

STORAGE

Store heater in a clean dry place when not in use.

CAUTION

NO SERVICING of the internal or electrical parts should be performed by the consumer. Do not service the unit yourself.

TROUBLESHOOTING

CAUTION

Disconnect the appliance completely and let cool prior to any service.
Only a qualified service person should service and repair this electric appliance.

CAUTION

To remove the glass, you will notice two screws on top sides (right and left) of the fireplace. Once the screws are removed, slide the glass up and away from the fireplace. Once the bottom frame plate is removed, you will notice one flame motor on right side where the rod should be in place with the rubber plugs.
Please remember to always have the unit disconnected prior to any work, always lay glass as well as the unit on a towel or other material not to damage parts/frame.
This entire process should not take longer than 20-30 minutes.