JBLQUANTUM610BLK Quantum 610 Wireless User Guide

JBLQUANTUM610BLK Quantum 610 Wireless

WHAT’S IN THE BOX

Product Information

• Driver size: N/A
• Frequency response: N/A
• Microphone frequency response: N/A
• Max input power: N/A
• Sensitivity: N/A
• Maximum SPL: N/A
• Microphone sensitivity: N/A
• Impedance: N/A
• 2.4G Wireless transmitter power: N/A
• 2.4G Wireless modulation: N/A
• 2.4G Wireless carrier frequency: N/A
• Battery type: N/A
• Power supply: USB charging cable
• Charging time: 3 hours
• Music play time with RGB lighting off: N/A
• Microphone pickup pattern: N/A
• Weight: N/A

Product Usage Instructions:

1. Download JBL QuantumENGINE to gain full access to features on your JBL Quantum headsets – from headset calibration to adjusting 3D audio to suit your hearing, from creating customized RGB lighting effects to determining how the boom microphone side-tone works. Visit JBLquantum.com/engine to download.

2. Check that your device meets the software requirements (Windows 10 64-bit or Windows 11, with 500MB of free hard drive space for installation).

3. Connect the headset using the 3.5mm audio cable or the USB wireless dongle.

4. If using the USB wireless dongle for the first time, follow the first-time setup instructions:

   • Connect the headset to your PC via 2.4G USB wireless connection.

   • Go to Sound Settings -> Sound Control Panel.

   • Under Playback highlight JBL QUANTUM610 WIRELESS GAME and
     select Set Default -> Default Device.

   • Highlight JBL QUANTUM610 WIRELESS CHAT and select Set Default -> Default Communication Device.

   • Under Recording highlight JBL QUANTUM610 WIRELESS CHAT and select Set Default -> Default Device.

   • In your chat application select JBL QUANTUM610 WIRELESS CHAT as the default audio device.

   • Follow the onscreen instructions to personalize your sound settings.

5. To adjust audio balance, use the game audio-chat balance dial or volume control button.

6. To mute or unmute the microphone, use the microphone mute/unmute button or notification LED for mic mute/unmute.

7. To turn the headset on or off, use the power on/off slider or hold the power on/off button for more than 5 seconds.

8. To increase or decrease volume, use the volume control knob or button.

9. To customize RGB lighting effects, use JBL QuantumENGINE software.

JBL QuantumENGINE

Download JBL QuantumENGINE to gain full access to features on your JBL Quantum headsets – from headset calibration to adjusting 3D audio to suit your hearing, from creating customized RGB lighting effects to determining how the boom microphone side-tone works. JBLquantum.com/engine

Software requirements

• Platform: Windows 10 (64 bit only) / Windows 11
• 500MB of free hard drive sp ace for installation

Always use the latest version of Windows 10 (64 bit ) or Windows 11 for the most optimal experience on JBL QuantumENGINE

JBL QuantumSURROUND and DTS Headphone: X V2.0 available on Windows only. Software installation is required.

Requirements

JBL QuantumENGINE SOFTWARE REQUIREMENTS

• _ Platform: _Windows 10 (64 bit only) / Windows 11 500MB OF FREE HARD DRIVE SPACE FOR INSTALLATION

System compatibility

• PC | Xbox™ | PlayStation™ | Nintendo Switch™ | Mobile | MAC | VR

Connectivity| PC| PS4/PS5| XBOX™| Nintendo Switch™| Mobile| MAC| VR
---|---|---|---|---|---|---|---
3.5 mm Audio Cable| Stereo| Stereo| Stereo| Stereo| Stereo| Stereo| Stereo
2.4G Wireless| | Stereo| Not Compatible| Stereo| Not Compatible| Stereo| Stereo

OVERVIEW

1. Game audio-chat balance dial
2. Volume Control
3. Detachable Windshield foam
4. Notification LED for mic mute / unmute
5. RGB-lit JBL logo
6. CHARGING LED
7. 3.5mm Audio Jack
8. USB-C port
9. Voice Focus Boom Microphone
10. Flat-fold ear cup
11. Microphone Mute / unMute
12. POWER / 2.4G LED
13. POWER ON / OFF slider
14. 2.4G PAIRING BUTTON
15. Volume Control
16. MIC MUTE BUTTON

POWER ON & CONNECT

2.4G Wireless

MANUAL CONTROLS

SETUP

BUTTON COMMAND

• INCREASE GAME VOLUME
• INCREASE CHAT VOLUME
• INCREASE MASTER VOLUME
• DECREASE MASTER VOLUME
• Microphone Mute / unMute x1
• ON / OFF >5S

First-time setup

• Connect the headset to y our PC via 2.4G USB wireless connection.
• Go to “Sound Settings” -> “Sound Control Panel”.
• Under “Playback” highlight “JBL QUANTUM610 WIRELESS G AME” and select “Set Default” -> “Default Device”.
• Highlight “JBL QUANTUM610 WIRELESS CHAT” and select “ Set Default” -> “Default Communication Device”.
• Under “Recording” highlight “JBL QUANTUM610 WIRELESS CHAT” and select “Set Default” -> “Default Device”.
• In your chat application select “JBL QUANTUM610 WIRELESS CHAT” as the default audio device.
• Follow the onscreen instructions to personalize y our sound settings.

MICROPHONE

CHARGING

LED BEHAVIOURS

TECH SPEC

• Driver size: 50 mm Dynamic drivers
• Frequency response: 20 Hz – 20 kHz
• Microphone frequency response: 100 Hz -10 kHz
• Max input power: 30 mW
• Sensitivity: 100 dB SPL @1 kHz / 1 mW
• Maximum SPL: 95 dB
• Microphone sensitivity: -40 dBV/Pa @1 kHz
• Impedance: 32 ohms
• 2.4G Wireless transmitter power: <14 dBm
• 2.4G Wireless modulation: GFSK, /4 DQPSK
• 2.4G Wireless carrier frequency: 2400 MHz – 2483.5 MHz
• Battery type: Li-ion battery (3.7 V / 1000 mAh)
• Power supply: 5 V 2 A
• Charging time: 3 hrs
• Music play time with RGB lighting off: 40 hrs
• Microphone pickup pattern: Unidirectional
• Weight: 357 g

IC RF Exposure Statement

IC RF Exposure Information and Statement

The SAR limit of Canada (C) is 1.6 W/kg averaged over one gram of tissue. Device types: (IC: 6132A-JBLQ610) has also been tested against this SAR limit According to this standard, the highest SAR value reported during product certification for head use is 0.014 W/Kg. The device was tested for typical bodily operations where the product was kept 0 mm from the head. To maintain compliance with IC RF exposure requirements, use accessories that maintain a separation distance of 0mm between the user›s head and the back of the headset. The use of belt clips, holsters and similar accessories shall not contain metal parts in its assembly. Use of accessories that do not meet these requirements may not comply with IC RF exposure requirements and should be avoided.

IC RF Exposure Information and Statement for USB Wireless Dongle

The SAR limit of Canada (C) is 1.6 W/kg averaged over one gram of tissue. Device types: (IC: 6132A-JBLQ610TM) has also been tested against this SAR limit According to this standard, the highest SAR value reported during product certification for head use is 0.099 W/Kg.

Head operation

The device was subjected to a typical head manipulation test. In order to comply with RF exposure requirements, a minimum separation distance of 0 cm must be maintained between the user›s ear and the product (including the antenna). Head exposure that do not meet these requirements may not meet RF exposure requirements and should be avoided. Use only the supplied or approved antenna.

IC: 6132A-JBLQ610

Body operation

The device was tested for typical bodily operations where the product was kept with 5 mm distance attached away from the body. Non-compliance with the above restrictions may result in violation of IC RF exposure guidelines. Use only the supplied or approved antenna.

IC: 6132A-JBLQ610TM

This product is homologated by Anatel, in accordance with the regulated procedures for evaluating the conformity of products for telecommunications and meets the applied technical requirements. For more information, consult the Anatel website – www.anatel.gov.br This equipment is not entitled to protection against harmful interference and may not cause interference to systems duly authorized.

Custom headphones **

**

• Manufacturer: Harman International Industries Incorporated, USA, 06901 Connecticut, Stamford, 400 Atlantic Street, office 1500 Made in China
• Importer: LLC “HARMAN RUS CIS”, Russia, 127018, Moscow, st. Dvintsev, 12, building 1

Warranty

• Warranty period: 1 year Service life: 2 years
• Service center information: www.harman.com/ru
• Technical support: 8 (800) 700 0467
• An organization authorized to accept consumer claims: HARMAN RUS CIS LLC.

The product is certified.

The date of manufacture of the device is determined by two letters from the second group of symbols of the serial the product number following after the delimiter “-“. The encoding corresponds to the order of the letters of the Latin alphabet, starting from January 2010: 000000-MY0000000, where “M” is the month of production (A – January, B – February, C – March, etc.) and “Y” – year of production (A – 2010, B – 2011, C – 2012, etc.).

FCC ID: APIJBLQ610

References

• JBL Quantum Support
• Anatel — Agência Nacional de Telecomunicações

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>