A-NEUVIDEO ANI-4KHPN 4K UHD+ HDMI to HDMI Scaler w/ EDID Management Instruction Manual

ANI-4KHPN 4K UHD+ HDMI to HDMI Scaler w/ EDID Management
Instruction Manual

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by  items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated.

9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty.

10. Turn power off and disconnect unit from AC current before making connections.

11. Never hold a power switch in the “ON” position.

12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.
    Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.

13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.

14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no  user serviceable parts inside.

15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices.

16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing.

19. Service Information Equipment should be serviced by qualified service personnel when:
    A. The power supply cord or the plug has been damaged.
    B. Objects have fallen, or liquid has been spilled into the equipment.
    C. The equipment has been exposed to rain.
    D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
    E. The equipment has been dropped, or the enclosure damaged.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you  unpack and install this equipment:

• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.

DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means — electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without the express written permission and consent.
© Copyright 2021. All Rights Reserved.
Version 1.0 DEC 2021
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

INTRODUCTION

This compact yet versatile HDMI to HDMI UHD Scaler accepts and outputs a wide range of resolutions up to 4K@60Hz (4:4:4, 8-bit) with simultaneous audio embedding  and de-embedding of digital (HDMI or optical) or analog audio. Integrated EDID and HDCP management options allow for control over the way connected sources and  displays detect the unit. The scaled HDMI output is powered by a high quality single-pass scaling engine with the ability to adjust the image with a number of fine tuning  options including: contrast, brightness, hue, saturation, sharpness, noise reduction, and RGB levels. 3-D motion adaptive de-interlacing and frame rate conversion is supported as well.
The HDMI input and output supports passing up to LPCM 7.1 digital audio as well as Bitstream and HD Bitstream audio formats. Audio embedding and de- embedding is  also available with the included digital optical and analog stereo audio inputs and outputs (LPCM 2.0 only). Shortcut keys are provided to quickly change the output resolution to 1080p@60Hz or XGA when needed for quick connection to a display or for troubleshooting purposes.
This is an ideal device to integrate previously incompatible sources and displays in your boardroom, classroom, or home. This unit is controlled via a comprehensive On- Screen Display (OSD) menu that provides the user with easy access to all settings. These products have a 3 year warranty.

PACKAGE CONTENT

Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton:

• ANI-4KHPN HDMI to HDMI Scaler
• 5V/2.6A DC Power Adapter
• Users Guide

FEATURES / SYSTEM REQUIREMENTS/ APPLICATIONS

FEATURES

• HDMI input and output with 18Gbps (600MHz) 4K UHD support
• DVI 1.0 compliant with the use of an HDMI-DVI adaptor
• HDCP 2.2 and HDCP 1.x compliant
• HDMI input and 1 HDMI output
• Digital Optical Audio (TOSLINK) and 1 Analog Stereo Audio input
• Digital Optical Audio (TOSLINK) and 1 Analog Stereo Audio output
• HDMI input supports resolutions up to 4096x2160p@60Hz (4:4:4, 8-bit)
• Scaled HDMI output supports resolutions from 640×480@60Hz up to 4096x2160p@60Hz (4:4:4, 8-bit)
• Supports pass-through of many audio formats including LPCM 2.0/5.1/7.1, Bitstream, and HD Bitstream via HDMI
• Supports audio embedding and de-embedding via digital optical and analog stereo audio inputs and outputs (LPCM 2.0 only)
• Supports frame rate conversion, 3-D motion adaptive de-interlacing, and 3:2/2:2 pull-down detection and recovery
• Supports output adjustments to contrast, brightness, hue, saturation, sharpness, RGB levels and aspect ratio
• Integrated EDID and HDCP management
• Controllable via front panel buttons with comprehensive OSD

SYSTEM REQUIREMENTS

• HDMI source equipment such as media players, video game consoles or set-top boxes.
• HDMI receiving equipment such as HDTVs, monitors or audio amplifiers.
• The use of “Premium High Speed HDMI” cables is highly recommended.

APPLICATIONS

• Entertainment Rooms & Home Theaters
• Showrooms & Demo Rooms
• Lecture Hall Presentations
• Public Commercial Displays
• AV Equipment and Control Rooms

As product improvements are continuous, specifications are subject to change without notice.

OPERATION CONTROLS & FUNCTIONS

Front Panel

1. HDMI OUTPUT: Connect to an HDMI TV, monitor or amplifier for digital video and audio output.
2. TOSLINK INPUT: Connect to powered speakers or an amplifier for digital audio output using an appropriate optical cable.
3. AUDIO INPUT: Connect to powered speakers or an amplifier for stereo analog audio output.
4. MENU: Press to enter the OSD menu, to confirm a selection within the OSD or to go deeper into a menu item. To back out from menu items or exit the menu, select the “Exit” option.
5.  & +: Press to move up and down or adjust selections within OSD menus.
   Note: Pressing “MENU” and “+” together will reset the output resolution to XGA (1024×768@60Hz).
   Pressing “MENU” and “−” together will reset the output resolution to 1080p@60Hz. Pressing and holding the “−” button while powering the unit on will perform a factory reset.

BACK Panel

1. SERV.: This port is reserved for firmware update use only.
2. AUDIO INPUT: Connect to the stereo analog output of a device such as an audio player or PC.
3. TOSLINK INPUT: Connect to the optical audio output of a device such as a media player or game console using an appropriate optical cable.
4. HDMI INPUT: Connect to HDMI source equipment such as a media player, game console or set-top box.
5. DC 5V & LED: Plug the 5V DC power adapter into this port and connect it to an AC wall outlet for power. The LED will illuminate to indicate the unit is on and receiving power.

OSD Menu
All functions of this unit can be controlled by using the OSD (On Screen Display) which is activated by pressing the MENU button on the front of the unit. Use the + (Plus),  − (Minus), and MENU buttons to navigate the OSD menu. Select the “EXIT” option to back out from any menu item and then select it again to close the menu.

MAIN MENU

VIDEO
PICTURE
AUDIO
OSD
EDID
RESET
FW UPDATE
INFORMATION
EXIT

The individual functions of the OSD will be introduced in the following section. Items marked in BOLD are the factory default settings.

VIDEO

800×600 60
1024×768 60
1280×768 60
1280×800 60
1280×1024 60
1360×768 60
1400×1050 60
1440×900 60
1600×1200 60
1600×1200 60
1680×1050 60
1920×1200 60 RB
2560×1600 60
1920×1080 60
1280×720 60
2048×1080 50
2048×1080 60
602560×1440 60 RB
720x480P 60
1280x720P 60
1920x1080P 60
720x576P 50
1280x720P 50
1920x1080P 50
1920x1080P 24
1920x1080P 25
1920x1080P 30
2ND LEVEL| 3ND LEVEL| 4TH LEVEL
---|---|---
OUTPUT| 2560x1080P 50|
2560x1080P 60
3840x2160P 24
3840x2160P 25
3840x2160P 30
3840x2160P 50
3840x2160P 60
4096x2160P 24
4096x2160P 25
4096x2160P 30
4096x2160P 50
4096x2160P 60
Native
ASPECT| Over Scan|
FULL
Best Fit
Pan Scan
Letter Box
Under 2
Under 1
Follow In
Zoom Mode
ZOOM MODE RATIO| 60~180 (100)|
HDCP| Off|
Refer to Source
REFER TO DISPLAY
NO SIGNAL COLOR| BLACK|
White
2ND LEVEL| 3ND LEVEL| 4TH LEVEL
---|---|---
NO SIGNAL COLOR| Blue|
Red
Green
BLANK| OFF|
On
FREEZE| OFF|
On
AUTO SYNC OFF| OFF|
30s
60s
3 Min
5 Min
10 Min
OUTPUT SETTING| Bypass Enable| OFF
On
Output 4K(6G) YUV420| OFF
On
EXIT|
EXIT| |

1. OUTPUT: Selects the output resolution to use. Selecting “Native” will make the unit automatically select an output resolution based on the detected EDID of the connected display.
2. ASPECT: Selects the aspect ratio to use when outputting the source. “Full” stretches the source to fill the output resolution, regardless of the original aspect ratio, while  “Best Fit” will always attempt to retain the original source’s correct aspect ratio by adding black bars if necessary. “Follow In” centers the source on the screen, without  any scaling (1:1 pixel reproduction). Selecting “Zoom Mode” activates the free-scaling zoom mode which allows for a zoom/shrink level to be manually selected using  the “Zoom Mode Ratio” setting. Note: Some video noise might be present when using the “Follow In” mode if the selected output resolution is 4096×2160@60Hz and the source is at, or above, 1680×1050 but below 3840×2160.
3.  ZOOM MODE RATIO: Sets the percentage amount to zoom or shrink the image when “Zoom Mode” is active.
4. HDCP: Selects the HDCP logic to use with the HDMI input. Setting this to “Off” will completely disable HDCP support on that input.
5. NO SIGNAL COLOR: Selects the free run color to use when no live input source is detected.
6. BLANK: Allows for the output video and audio to be blanked/ muted.
7. FREEZE: Allows for the output video to be frozen. While the output is frozen, audio output will also be muted.
8. AUTO SYNC OFF: Sets the amount of time to continue outputting sync with the free run color if there is no live source and no operations have been executed on the  unit. Setting this to “OFF” forces the unit to always output sync.
9. OUTPUT SETTING: Allows for configuring the following special video signal handing functions.
   • Bypass Enable: Enables or disables source bypass mode. When this is enabled, the video signal will be passed without modification.
   • Output 4K(6G) YUV420: Enables or disables the 4K@50/60 4:4:4 to 4K@50/60 4:2:0 color space conversion function.
   Note: Enabling Bypass mode will grey-out/disable the following Video Menu sections: Aspect, Zoom Mode Ratio, Freeze, Blank, and the entire Picture Menu section.

PICTURE

OSD Menu
PICTURE

Low
Middle
High
Auto
RESET PICTURE|
EXIT| EXIT

1. COLOR GAIN R/G/B: These controls provide control over the red, green, and blue color gain level of the scaled output.
2. COLOR OFF SET R/G/B: These controls provide control over the red, green, and blue color off set level of the scaled output.
3. BRIGHTNESS: Provides control over the overall brightness of the scaled output image.
4. CONTRAST: Provides control over the overall contrast of the scaled output image.
5. HUE: Provides control over the hue shift of the scaled output image.
6. SATURATION: Provides control over the color saturation level of the scaled output image.
7. SHARPNESS: Provides control over the amount of sharpness processing to apply to the scaled output image.
8. NR: Provides control over the aggressiveness of the digital noise reduction processing when applied to the scaled output image. Selecting “OFF” disables all noise reduction processing.
9. RESET PICTURE: Selecting this will reset all picture settings back to their factory defaults.

AUDIO

TOSLINK
Analog
VOLUME| 0~100 (80)
HDMI MUTE| OFF
On
TOSLINK MUTE| OFF
On
ANALOG MUTE| OFF
On
RESET AUDIO|
EXIT|

1. SOURCE: Provides control over the selection of the audio source to output. In “Auto” mode, if no audio source is detected the audio input will automatically switch to  the analog input.
   Note: If “Auto” is selected, and there is no video source, the analog audio will be heard while the free run color is displayed.

2. VOLUME: Provides control over the audio source’s volume level.
   Note: HDMI to HDMI audio is bypass only and the volume can not be adjusted.

3. HDMI MUTE: Mutes or unmutes the HDMI output’s audio.

4. TOSLINK MUTE: Mutes or unmutes the TOSLINK output’s audio.

5. ANALOG MUTE: Mutes or unmutes the analog output’s audio.

6. RESET AUDIO: Selecting this will reset all audio settings back to their factory defaults.

OSD

5s
10s
15s
20s
25s
30s
35s
40s
45s
50s
55s
60s
TRANSPARENT| 0~50 (50)
DISPLAY| Off
On
5S
10s
RESET OSD|
EXIT|

1. H POSITION: Set the horizontal position of the OSD menu.
2. V POSITION: Set the vertical position of the OSD menu.
3. TIMER: Set the length of time to wait before automatically turning off the OSD menu if there is no user interaction. The timer may also be disabled.
4. TRANSPARENT: Set the transparency level of the OSD menu. A setting of 50 is completely opaque.
5. DISPLAY: Enable or disable the information display and set the length of time for the information display to be visible after a source or resolution change.
6. RESET OSD: Selecting this will reset all OSD settings back to their factory defaults.

EDID

FHD Much
UHD 2Ch
UHD Much
UHD+ 2Ch
UHD+ Much
Output
Auto Output
EXIT|

1. HDMI EDID: Select the EDID to use with the HDMI input. Selecting “Output” will copy and use the current sink’s EDID but will not re-copy the EDID if the sink is  changed. Selecting “Auto Output” will automatically copy and use the EDID from the current sink every time a new sink is connected.

RESET

1. RESET ALL: Selecting this will reset the unit’s settings back to their factory defaults.
FW UPDATE

1. UPDATE FROM USB: Provides a way to update the unit’s firmware. Insert a USB thumb drive, with a valid firmware file (*.bin format) in the root directory, into the  unit’s USB service port then select this option. After the update is complete the unit will automatically reboot.

INFORMATION

INPUT COLOR
INPUT RESOLUTION
INPUT HDCP
OUTPUT FORMAT
OUTPUT COLOR
OUTPUT RESOLUTION
OUTPUT HDCP
SINK HDCP
VERSION

1. INFORMATION: This screen displays information about the unit’s current state, input and output status, as well as the current firmware version.

CONNECTION DIAGRAM

Video Specifications

SUPPORTED PC RESOLUTION (HZ)| HDMI Input| HDMI Output| | SUPPORTED PC RESOLUTION (HZ)| HDMI Input| HDMI Output
---|---|---|---|---|---|---
640×480@60/72/75/85| | 60Hz| 1440×900@60/60 (RB)| | 60Hz
800×600@56/60/72/75/85| | 60Hz| 1600×1200@60| |
1024×768@60/70/75/85| | 60Hz| 1680×1050@60/60 (RB)| | 60Hz
1280×720@50/60| | 60Hz| 1920×1080@60| |
1280×768@60/75/85| | 60Hz| 1920×1200@60 (RB)| |
1280×800@60/60 (RB)| | 60Hz| 2560×1600@60| **|
1280×1024@60| | | 2048×1080@50| |
1360×768@60| | | 2048×1080@60| |
1400×1050@60/60 (RB)| | 60Hz| 2560×1440@60 (RB)| |
SUPPORTED TV RESOLUTION (HZ)| HDMI Input| HDMI Output| | SUPPORTED TV RESOLUTION (HZ)| HDMI Input| HDMI Output**
720x480i@60| | x| 1920x1080i@50/60| |
720x480p@60| | | 1920x1080p@24/25/30/50/60| |
720x576i@50| | x| 2560x1080p@50/60| |
720x576p@50| | | 3840x2160p@24/25/30/50/60| |
1280x720p@50/60| | | 4096x2160p@24/25/30/50/60| |

AUDIO SPECIFICATIONS

CABLE SPECIFICATIONS

TERMS AND CONDITIONS OF USE
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-Menu:video, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-Neu Video,  Inc. at the return address set forth on the Product’s packing label at your expense. A-Neu Video, Inc. may modify these Terms and Conditions at anytime, without notice to  you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You are  authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining  to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-Neu Video, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to A-Neu Video. Any intellectual property rights pertaining to the Product are licensed  to you by A-Neu Video, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-Neu Video”) for your personal use only,  provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-Neu Video for your personal use only. A-Neu Video does not transfer either the title or the intellectual property rights to the Product and A-Neu Video retains full and complete title to the intellectual property rights therein.
All trademarks and logos are owned by A-Neu Video or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-Neu Video, which consent may be withheld at the sole discretion of A-Neu Video.
The functionality and usability of the Product is controlled by A-Neu Video, Inc. from its offices within the State of Texas, United States of America. A-Neu Video makes no
representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls.
DISCLAIMERS AND LIMITATION OF LIABILITY
A-Neu Video may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE.
A-Neu Video has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied  upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS  OR OTHER HARMFUL COMPONENTS. A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY A-NEUVIDEO.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.

END OF DOCUMENT

Documents / Resources

| A-NEUVIDEO ANI-4KHPN 4K UHD+ HDMI to HDMI Scaler w/ EDID Management [pdf] Instruction Manual
ANI-4KHPN 4K UHD HDMI to HDMI Scaler w EDID Management, ANI-4KHPN, 4K UHD HDMI to HDMI Scaler w EDID Management, Scaler w EDID Management
---|---

References

• A-NeuVideo.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>