TORNADO HI-FAN-12HVWM-WR-1P Outdoor Rated Water Resistant High Velocity Metal Wall Fan Instruction Manual
- June 9, 2024
- Tornado
Table of Contents
TORNADO HI-FAN-12HVWM-WR-1P Outdoor Rated Water Resistant High Velocity
Metal Wall Fan
Product Information
The TOARDO 12 Outdoor Rated Water Resistant High-Velocity Metal Wall Fan Model: HI-FAN-12HVWM-WR-1P is a commercial or industrial-grade product that is suitable for outdoor use. This fan is designed to improve the air circulation in large spaces such as warehouses, factories, and workshops.
The product comes with a grounding conductor and a GFCI type plug to reduce the risk of electrical shock. The fan is equipped with a power supply with a ground fault circuit interrupting device, and it is not recommended to remove or tamper with the power cord. The product comes with a warning label to caution users against using it with any solid-state speed control device.
Product Usage
Before using the product, make sure that your electrical wiring meets the appropriate codes and ordinances. If you are unsure about your wiring, consult a qualified electrician.
When using the fan, follow the instructions below:
- Do not operate the fan with a damaged power cord or after the fan malfunctions or has been dropped in any manner.
- Do not allow children, disabled persons, or pets near the fan and whenever it is left operating unattended.
- Ensure that the fan is placed in a stable location that will prevent tipping or falling. Take extra care when assembling or disassembling parts and before cleaning.
- Do not use the product with any solid state speed control device.
- Ensure that the power is disconnected before servicing the product.
- If you need to replace the power cord, consult a service center or a qualified electrician to install an appropriate replacement cord to prevent any injury or damage.
- Ensure that the fan is at least 7 feet above the floor and away from throw rugs, runners, or any traffic area where it may be tripped over.
- Avoid contact with moving parts to prevent electric shock and/or fire hazard.
- Do not allow persons (especially children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge to use the appliance unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Finally, ensure that the fan is connected only to a properly grounded outlet. Do not use the product with a damaged cord or plug, and make sure to connect the fan only to an outlet provided with a ground fault circuit interrupting device. Never remove the power plug’s ground prong or ground fault unit. All installations must be made into a grounded outlet.
PLEASE READ AND SAVE THIS INSTRUCTION.
Attention: Pictures in the IM are for reference only.
Intended Use:
This product is intended for industrial or commercial use only. Use only with
electrical wiring that is in good working order and that meets applicable
codes and ordinances. If you have any questions whether your wiring is
adequate, consult a qualified electrician.
This fan is suitable for outdoor use.
While using your fan, you should follow the IMPORTANT INSTRUCTIONS listed
below. As part of those instructions, we have used the word “WARNING” to
indicate the level of hazard:
WARNING indicates a hazard which, if not avoided, could result in injury or death.
IMPORTANT INSTRUCTIONS
As with all electrical appliances, basic safety precautions should always be followed to reduce the risk of electric shock, fire, or injury to persons, including the following precautions:
- Read all the instructions before using this fan.
- Use this fan only as described in this manual. Any other use not recommended by the manufacturer may cause electrical shock, fire or injury to persons.
- Do not operate the fan with a damaged power cord or after the fan malfunctions or has been dropped in any manner.
- Use of extreme caution is necessary when any fan is used by or near children, disabled persons or pets and whenever the fan is left operating unattended.
- Do not place the fan on a small, unlevel, uneven or any surface which might allow fan to tip or fall.
- Always unplug fan when not in use, when moving from place to place, when assembling or disassembling parts, and before cleaning.
- The use of attachments, not recommended or sold by the manufacturer, may cause hazards.
- To reduce the risk of fire or electrical shock, do not use this fan with any solid state speed control device.
- Do not operate the fan with blade guards or any safety device removed.
- Automatically operated device – To reduce the risk of injury, disconnect from power supply before servicing.
- If the power supply cord is damaged, contact your local service center or a qualified electrician to install an appropriate replacement cord to prevent any injury or damage.
- Do not use an extension cord with this fan.
- To reduce the risk of injury to persons, install fan at least 2.1m (7 feet) above the floor.
- Do not run power cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic area where it will not be tripped over.
- Do not insert or allow any object to enter any openings on the fan. Doing so may cause electric shock and/or fire hazard. Avoid contact with moving parts.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure they do not play with the appliance.
READ & SAVE THESE INSTRUCTIONS
WARNING:
Risk of electrical shock—This fan is supplied with a grounding conductor and
GFCI type plug. To reduce the risk of electrical shock, make sure that it is
connected only to a PROPERLY grounded outlet.
Use only on GFCI protected receptacles.
To Reduce The Risk Of Electric Shock, Connect Only To An Outlet Provided With
A Ground Fault Circuit Interrupting Device.
Do not under any circumstances remove the power plug’s ground prong or ground
fault unit. For your personal safety, the fan must be grounded.
The fan is equipped with a power supply with ground fault circuit interrupting
device. Removal or tampering of power cord will void warranty.
Never use an extension cord to connect the fan to an outlet. All installations
must be made into a grounded outlet.
WARNING:
Electrical Shock Hazard
Do not use with damaged cord or plug. Use with adequate electrical system that
is up to code.
CAUTION: To reduce the risk of electric shock, connect only to an outlet
WARNING: to Reduce the Risk of Fire or Electric Shock, do not use this product with any solid‑state speed control device.
DANGER: Do not submerge motor in water or allow motor to be exposed to water. Personal injury and/or death could result. Never handle the fan or motor with wet hands or when standing on wet or damp surface or in water. Fatal electrical shock could occur.
Installation Instructions
Use the following information as a guideline only. It is the user’s
responsibility to be sure the location and the wall surface can handle the
weight of this fan (14.6 lbs).
The wall fan must be mounted on 12 inch (300mm) thick dry and cement-grouted
firm wall or on 4 by 5-inch wood studs/joists.
Use wall bracket as a template for locating the holes to be drilled.
After determining the hole locations, use an appropriate-sized drill bit and,
drill holes through mounting surface.
It is recommended that a minimum of grade 5 fasteners be used. The following
are acceptable surfaces for mounting wall mount assembly.
STEEL SURFACE ‑ When mounting to a steel surface, such
as vertical I‑beam, drill through holes at pre‑marked locations, using a 9/32″
drill bit. Attach wall mount assembly to mounting surface using 1/4″‑20 hex
screw, in combination with 1/4″ flat washers, 1/4″ lock washers, and 1/4″‑20
hex nuts.
MASONRY SURFACE ‑ When mounting to a masonry surface use a 1/4″ expansion
type bolt or 1/4″ masonry lag with
shield designed to handle the weight of this fan. Drill holes at pre‑marked
locations using appropriate-sized drill bit as recommended for the fastener.
Usage:
Fan operation: Always operate the fan in the upright position following
all instructions and recommendations listed in this manual.
Fan location: Place the fan in the area of the room that will provide
proper fan cooling.
Fan connection: Plug fan directly into 120 volt A.C., 60 Hz wall outlet. Be
sure plug fits tightly in outlet. A loose connection may cause overheating and
damage to the plug or fan.
Note: To prevent overloading a circuit, do not plug the fan into a circuit that is servicing other electrical needs.
Speed control: To operate the fan, each pull of the string will cycle through the following settings:
- OFF
- LOW
- MED
- HIGH
- OFF
We are happy to help, contact us : info@tornadofans.com
Care and Maintenance
Cleaning: CAUTION-Before cleaning the fan be sure to disconnect power
cord from the plug. Clean the grille surface with a clean damp cloth. Do not
use harsh chemical or abrasive cleaners. DO NOT IMMERSE THE FAN OR ANY WIRES
IN WATER. Replace front grille before fan use. Allow fan to dry completely
before use. Periodic grille cleaning with a vacuum will prevent dust build up.
The motor is sealed and does not require any interior maintenance, cleaning or
lubrication.
Maintenance: The Internal motor bearings are permanently lubricated at
the factory and do not require any additional lubrication.
Repair: DO NOT OPERATE THE FAN WITHOUT THE GRILLE IN PLACE. DO NOT USE
THE FAN IF IT HAS MALFUNCTIONED OR BECOME DAMAGED IN ANY WAY.
Storage: Keep original carton for storage of the fan. Coil and tie the power cord to avoid damage during storage.
LIMITED ONE-YEAR WARRANTY
Hexago LLC warrants this product to be free of defects in material and workmanship for the applications specified in the Owner’s Manual for a period of 12 months for the whole fan from date of purchase. This warranty only applies to the original purchaser of this product.
This warranty excludes damage, accidental or otherwise, to the unit not caused
by a defect in material or workmanship.
The warranty also exlcudes damage caused by misuse, tampering, modification,
missassembly, repairs or alternations, or failure to adequately maintain and
care for the unit. Operating this product under any conditions others than
those recommended or at voltages other than indicated will also void this
warranty. For warranty issues, contact the place of purchase for repair/
replacement opportunities. The original dated receipt or proof of purchase
must accompany all returns.
All warranties, expressed or implied, are limited for 12 months for the whole fan from the date of purchase. Please contact us at www.tornadofans.com if you have any questions. Tornado is a registered trademark of Hexago LLC.
Some states do not allow for the limitation or exclusion of incidental or consequential damages, or do not allow limitation on implied warranties. The above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and may also include other rights that vary state by state.
Customer service email: info@tornadofans.com
Website: www.tornadofans.com
FOR CALIFORNIA CONSUMERS WARNING: This product can expose you to chemicals including lead and phthalates,which are known to the state of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>