FABTECH FT28011 1.5 Inch Coil Assist Kit Instructions
- June 9, 2024
- FABTECH
Table of Contents
FABTECH FT28011 1.5 Inch Coil Assist Kit
Product Information
The FTS28011 Wheel Spacer Kit is designed for 2015-2021 Mercedes Sprinter 2500 4WD vehicles. It includes a hardware subassembly, wheel spacer, lug nuts, lug nut socket, instructions sticker, driver warning decal, thread locking compound, and registration card. The kit contains a front wheel spacer only, and for rear wheel spacer installation, an additional FTS28011 kit is required. It is recommended to use basic hand tools, a floor jack, jack stands, assorted metric and S.A.E sockets and Allen wrenches, and a torque wrench to install the kit. For technical assistance orwearable replacement components, contact Fabtech Motorsports at 909-597-7800 or email info@fabtechmotorsports.com.
Product Usage Instructions
-
Disconnect the negative terminal on the battery and jack up the front end of the truck. Support the frame rails with jack stands.
-
Remove the front tires.
-
Install the new FT19014 (Threaded Stud) into the rotor hat assembly by hand using thread locking compound on the smaller threaded end. Torque the studs to 12 ft-lbs using a 5mm Allen socket and torque wrench.
-
Install FT19023 (Wheel Spacer) onto the vehicle.
-
Install tires and wheels using the supplied lug nuts. Torque to 120ft-lbs.
-
Turn front tires left to right and check for appropriate tire clearance. Note – Some oversized tires may require trimming of the front bumper & valance.
-
Check front end alignment and set to factory specifications.
Readjust headlights. -
Recheck all nuts, bolts, and lugs for proper torque. Re-torque all after 50 miles and periodically thereafter until torque values are retained.
-
Recheck brake hoses, ABS wires, and suspension parts for proper tire clearance while turning tires fully left to right.
-
Check ball joints, uniballs bearings, bushings, and all steering components every 2500-5000 miles for wear and replace as
required. -
Install Driver Warning Decal. Complete product registration card and mail to Fabtech in order to receive future safety and technical bulletins on this suspension.
-
Review all included warnings and warranties with the consumer.
Before starting installation, it is important to read all warnings and warranties on the last page of the instructions.
Follow the footnotes provided in the instructions to order wearable replacement components from the Fabtech website.
Please note that the product comes with a limited lifetime warranty for defects in workmanship and materials. For any technical assistance or product- related query, contact Fabtech Motorsports at 909-597-7800 or email: info@fabtechmotorsports.com.
| FTS28011| MERCEDES SPRINTER 2500 WHEEL SPACER
KIT
---|---|---
2| FT19023| WHEEL SPACER
1| FT19024| HARDWARE SUBASSEMBLY
| FT19024| HARDWARE SUBASSEMBLY
---|---|---
12| FT19014| WHEEL STUD M14-1.5 X 78MM
12| FT19025| LUG NUT M14X1.5
1| FT19028| LUG NUT SOCKET
1| FT28011i| INSTRUCTIONS
1| FTAS12| STICKER 10X4
1| FTAS16| DRIVER WARNING DECAL
2| FTLOCK| THREAD LOCKING COMPOUND
1| FTREGCARD| REGISTRATION CARD
TOOL LIST
Required Tools (Not Included)
- Basic Hand Tools
- Floor Jack
- Jack Stands
- Assorted Metric and S.A.E sockets, and Allen wrenches Torque Wrench
PRE-INSTALLATION NOTES
For technical assistance call: 909-597-7800 or e-mail: info@fabtechmotorsports.com
READ THIS BEFORE YOU BEGIN INSTALLATION
- Check all parts to the parts list above before beginning installation. If any parts are missing contact Fabtech at 909-597-7800 and a replacement part will be sent to you immediately.
- This suspension and shocks have been designed to be installed on a stock vehicle.
- Read all instructions thoroughly from start to finish before beginning the installation. If these instructions are not properly followed severe frame, driveline and / or suspension damage may occur.
- Check your local city and state laws prior to the installation of this system for legality. Do not install if not legal in your area.
- Prior to the installation of this suspension system perform a front end alignment and record. Do not install this system if the vehicle alignment is not within factory specifications. Check for frame and suspension damage prior to installation.
- The installation of this suspension system should be performed by two professional mechanics. This suspension must be installed with Fabtech shock absorbers.
- Installation of all fasteners requires the use of provided thread locking compound with proper torque values as indicated throughout the installation. Apply thread locking compound upon the final torque of the fastener.
- WARNING- Installation of this system will alter the center of gravity of the vehicle and may increase roll over as compared to stock. Extreme care should be taken to operate the vehicle safely at all times to prevent rollover or loss of control resulting in serious injury or death.
- Vehicles that receive oversized tires should check ball joints, uniballs, tie rods ends, pitman arm and idler arm every 2500- 5000 miles for wear and replace as needed.
- Verify differential fluid is at manufactures recommended level prior to kit installation. Installation of the kit will reposition the differential and the fill plug hole may be in a different position. (For example, if the manufacture recommends 3 quarts of fluid, make sure the diff has 3 quarts of fluid). Check your specific manual for correct amount of fluid.
- Read all warnings and warranties on the last page of these instructions before starting installation.
FOOTNOTES
Contains front wheel spacer kit only. For rear wheel spacer kit, order additional 1 each FTS28011
INSTRUCTIONS
FRONT SUSPENSION
- Disconnect the negative terminal on the battery. Jack up the front end of the truck and support the frame rails with jack stands. NEVER WORK UNDER AN UNSUPPORTED VEHICLE! Remove the front tires.
- Using the supllied thread locking compound on the smaller threaded end, install the new FT19014 (Threaded Stud) into the rotor hat assembly by hand. Then, using a 5mm allen socket and torque wrench, torque the studs to 12 ft-lbs. SEE FIGURES 1-2
-
Install FT19023 (Wheel Spacer) onto the vehicle. SEE FIGURE 3
-
Install tires and wheels using the supplied lug nuts. Torque to 120ft-lbs.
-
Turn front tires left to right and check for appropriate tire clearance. Note – Some oversized tires may require trimming of the front bumper & valance.
-
Check front end alignment and set to factory specifications. Readjust headlights.
-
Recheck all bolts for proper torque. RE-TORQUE ALL NUTS, BOLTS AND LUGS AFTER 50 MILES AND PERIODICALLY THEREAFTER UNTIL TORQUE VALUES ARE RETAINED.
-
Recheck brake hoses, ABS wires and suspension parts for proper tire clearance while turning tires fully left to right.
-
Check ball joints, uniballs bearings, bushings and all steering components every 2500-5000 miles for wear and replace as required.
-
Install Driver Warning Decal. Complete product registration card and mail to Fabtech in order to receive future safety and technical bulletins on this suspension.
-
Review all included warnings and warranties with consumer
For technical assistance call: 909-597-7800
Product Warranty & Warnings
- Fabtech provides a Limited Lifetime Warranty to the original retail purchaser who owns the vehicle, on which the product was originally installed, for defects in workmanship and materials.
- The Limited Lifetime Warranty excludes the following Fabtech items; bushings, bump stops, ball joints, Uniball bearings, tie rod ends, limiting straps, cross shafts, heim joints and driveshafts. These parts are subject to wear and are not considered defective when worn. They are warranted for 60 days from the date of purchase for defects in workmanship.
- Dirt Logic take apart shocks are considered a serviceable shock with a 1-year warranty against any manufacturer’s defects. If a shock fails within the initial year of ownership, the owner must ship the shock to Fabtech for inspection and service. If after examination the shock is determined to have failed due to neglect, damage caused by improper installation, or any reason other than “normal wear and tear,” the owner of the shock will be responsible for all service costs. Costs include labor, parts, and shipping. Service seal kits are available separately for future maintenance. All other shocks are covered under our Limited Lifetime Warranty.
- Fabtech does not warrant any product for finish, alterations, modifications and/or installation contrary to Fabtech’s instructions. Alterations to the finish of the parts including but not limited to painting, powder coating, plating and/or welding will void all warranties. Some finish damage may occur to parts during shipping, which is considered normal and is not covered under warranty.
- Fabtech products are not designed nor intended to be installed on vehicles used in race applications or for racing purposes or for similar activities. This warranty does not include coverage for police, taxi, first responder vehicles, race vehicles, or vehicles used for government, commercial or fleet purposes. Also excluded from this warranty are sales outside of the United States of America.
- Installation of most suspension products will raise the center of gravity of the vehicle and will cause the vehicle to handle differently than stock. It may increase the vehicle’s susceptibility to a rollover, on road and off road, at all speeds. Extreme care should be taken to operate the vehicle safely at all times to prevent rollover or loss of control resulting in serious injury or death.
- Oversized tires and wheels may decrease the vehicle’s braking capacity. Drivers should always brake early and be aware of the increased the stopping distance of the vehicle. Drivers should adjust their driving habits to the effectiveness of the braking. Adjust your driving habits to these changes.
- Failure to drive safely may result in serious injury or death to driver and passengers. Driver and passengers must ALWAYS wear your seat belts, avoid quick sharp turns and other sudden maneuvers
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>