ALKAWAY HIM-19 Hydrogen Inhaler User Manual

ALKAWAY HIM-19 Hydrogen Inhaler

Product Information: AlkaWay Hydrogen Inhaler

The AlkaWay Hydrogen Inhaler is a high-quality hydrogen inhaler that provides hydrogen-rich water and hydrogen gas for inhalation.
It features a nano-rod bubbler and SPE technology that ensures 99.9% pure hydrogen gas, low noise, and high efficiency. The unit has a smart indicator lamp, security settings, water level detection, and TDS detection. It is intelligently designed with safety and user in mind and has been extensively tested to ensure optimal performance.

Basic Parameters

• Hydrogen Purity: 99.9%
• Hydrogen Gas Flow Rate: 300 to 900ml/min
• Water Level Detection: Yes
• TDS Detection: Yes
• Noise Level: Low

Parts List:

1. Hydrogen Generator Machine
2. TDS Meter (LR44 button batteries not included)
3. Stainless Steel Nano-rod Bubbler
4. Cannulas
5. White Connection Tubes
6. Y Connectors

Product Usage Instructions

Unboxing:

1. Remove all packaging materials from the box.
2. Check the parts list to ensure that all components are
   present.

Using the Machine for the First Time:

1. Remove any caps on the Hydrogen and Oxygen outlets.

2. Unscrew and remove the tank cap, then pour distilled water (TDS
   < 10ppm) into the tank.

3. Replace the tank cap and connect the power supply.

4. Press the power button to turn on the machine.

5. The machine will automatically start producing hydrogen gas and
   the indicator light will turn blue.

How to Use the Machine

1. Connect one end of the white connection tube to the hydrogen outlet and the other end to the nano-rod bubbler.
2. Fill the nano-rod bubbler with distilled water (TDS < 10ppm).
3. Connect the cannula to the nano-rod bubbler.
4. Put the cannula into your mouth and inhale normally.
5. Adjust the hydrogen flow rate as desired using the control knob.

Precautions

• Do not use tap water or mineral water in the machine.
• Do not overfill the water tank.
• Do not disassemble or modify the machine.
• Keep the machine away from heat sources and direct
  sunlight.

Cleaning

• Turn off the machine and unplug it from the power source.
• Drain any remaining water from the tank.
• Clean the tank and nano-rod bubbler with a soft cloth and mild detergent.

Troubleshooting:

• If the machine does not turn on, check the power supply and connections.
• If the hydrogen purity is lower than 99.9%, replace the nano-rod bubbler.
• If there is water leakage, check the tank cap and connections.

(Please read this user manual carefully before using the Hydrogen Inhaler)

How to Operate

Unboxing

1. Parts list
   • Hydrogen generator machine
   • TDS meter (LR44 button batteries not included)
   • Stainless steel nano-rod bubbler
   • Cannulas
   • White connection tubes
   • Y connectors
2. First follow the instructions under the “Using the machine for the first time” section, and
3. Read the Precautions section (Very important).

Using the machine for the first time

1. Remove any caps on the Hydrogen and Oxygen outlets.

2. Unscrew and remove the tank cap, then pour distilled water (TDS<3) into the tank. Make sure the tank is at least ¾ full.

3. The drain outlet is located on the back of the machine. Position the back of the machine over a sink. Unscrew
   the drain cap. Water will pour out as soon as the cap is removed. Drain out about a third of the water. Then replace the drain cap.
   This is to ensure that the system is flushed fully. Leave overnight to fully soak the membrane and to ensure that the electrolytic cell is fully wet.

4. Connect the power cord and turn the power on (power switch and cord socket is on the back of the machine). The machine will beep and the screen will turn on.

5. Unscrew and remove the tank cap and top up the water tank with distilled water (TDS<3). To check the water level, use the water level observation window on the back of the machine. Then screw the tank cap back on.

6. If the water level is low an alarm will sound until the water level is back above the minimum level.

How to use the machine (Machine operation)

1. To turn the machine on, the main power switch is located on the back of the machine (red switch).
2. Press the button to set the flow rate. Pre-set flow rates, 300, 450, 600, 750 and 900 ml/min. For initial use, start with a lower flow rate until you get use to the hydrogen.
3. Press the button key to set the countdown clock. Pre-set times, 1,2,3,5 and 8 hours.
4. After setting the flow rate and the time, press the start   button to start the machine.
5. Press the button to turn OFF and ON the background light and the display.
6. When the machine is working, press the  button to stop the machine and reset the timer.
7. Once the countdown timer reaches zero the machine will beep and stop generating hydrogen.
8. When you have finished using the machine, turn it off at the power switch, (the red switch on the back of the machine.

Precautions

1. For adult use only.
2. Use only distilled water with a TDS of less than 3 to avoid voiding your warranty. Water with a TDS greater than 3 WILL damage the Cell. For the recommended brand of distilled water contact our Sales Support Team – 1800 268 469.
3. Always use in a well-ventilated or spacious room.
4. Operating temperature 5 to 30°C with a relative humidity of between 25 to 75°.
5. Do NOT use near an open flame (including smoke, burning incense or cigarettes) or a heater, or anything that sparks or has an open flame (within 3m).
6. Do NOT use when going to sleep. Remain awake at all times when using the machine.
7. Keep the power plug away from water.
8. Do NOT block the hydrogen and oxygen outlet holes when using the machine. Blocking these outlets will void the warranty.
9. Do NOT connect the bubbler to the Oxygen outlet, as the back pressure will cause damage to the cell and will void the warranty.
10. To maximise and maintain the optimal efficiency, the hydrogen generator should be rested for 2-3 hours after more than 2 consecutive hours of use. After each shorter time session, it is ideal to rest the machine off for 1-2 hours.
11. Don’t use the machine without water in it, this too voids the warranty.

Creating Hydrogen water with the bubbler

1. Push one end of the white connection tube onto the small end of the nano-rod bubbler.
2. Push the other end of the white connection tube onto the Hydrogen outlet on the machine.
3. Keep the Oxygen outlet open (not covered).
4. Place the larger end of the bubbler into a glass of water and start the machine.
5. Set the flow rate to 150ml/min.
6. Hydrogen-rich water will take between 5-10 minutes. So, stop the machine after 10 minutes.

Hint: The colder the water the more Hydrogen can be absorbed by the water.
Caution: Only connect the bubbler assembly to the Hydrogen outlet. DO NOT connect it to the Oxygen outlet, as the back pressure will cause damage to the Cell and will void the warranty.

Inhaling Hydrogen

1. Push the white connection tube onto the Hydrogen outlet.
2. Keep the Oxygen outlet open (not blocked).
3. Fit the cannula onto your nose as shown below.
4. Turn on the machine.
   Hints: Initially, start with 30 minutes a day at a flow rate of 300ml/min until the body gets used to the Hydrogen (1 week).
   Short sessions are more beneficial than longer sessions (1 hour ideally). Also rest the unit for 1-2 hours between each 1-hour session.
   Caution: Do NOT use near an open flame (including smoke, burning incense or cigarettes) or a heater or anything that sparks within 3 meters.

Inhaling Hydrogen and Oxygen

1. Push one end of 1 white connection tube onto the Oxygen outlet and the other end onto the Y-Connector (see image below), connect to the end indicated by the letter A.
2. Push one end of another white connection tube onto the Hydrogen outlet and the other end onto the Y-Connector (see image below), connect to the end indicated by the letter B.
3. Push the connection end of the Cannula onto the Y-Connector (see image below), connect to the end indicated by the letter C
4.  Fit the Cannula onto your nose as shown in the Inhaling Hydrogen section above.
5. Then, turn on the machine.

Cleaning

1. If the machine is used for more than 3 hours a day, it is recommended to replace the water in the machine every 7 days.
2. Otherwise, it is recommended to replace the distilled water after every 20 hours of use.
3. To clean, simply position the back of the machine over a sink. Unscrew the tank cap, then unscrew the drain cap. Water will pour out as soon as the drain cap is removed.
4. Refill the tank with distilled water (TDS<3). Allow to soak for 60 minutes, then drain out the water. Refill again with fresh distilled water (TDS<3).
5. If transporting the machine, drain out all the distilled water. Once you’re ready to use the machine again, refill the tank with distilled water (TDS<3).
6. If storing the machine for more than 2 weeks, drain out the distilled water. Once you’re ready to use the machine again, flush the machine as above and then refill the tank with distilled water (TDS<3).
7. Periodically empty out the water in the humidification bottle (refer to images on page 3).

Caution: Use only distilled water with a TDS of less than 3 to avoid voiding your warranty. And don’t use the machine without water in it, this too voids the warranty.

Basic parameters

Disclaimer

These products have not been medically evaluated and are not intended to diagnose, cure, treat or prevent disease. Seek medical advice if seriously ill or attempting to cure or prevent disease.
This product is not a medical device and is not advertised for any therapeutic effects.

Trouble Shooting

The machine is not starting

| ****

1.    Power plug is not plugged in properly

2.    ON/OFF button has not been pressed

3.    Is in screen saver mode

| ****

1.    Check that the plug is plugged in properly

2.    Check the Power is ON at the wall

3. Press the setting icon

There is no Hydrogen gas

| ****

1.    Not enough water in tank

2.    The cannula is not properly connected

3.    The bubbler is not properly connected

4.    TDS value of the distilled water is too high

| 1.    Fill the water tank to the top line on the water viewing panel.

2.    Ensure the cannula is properly connected and there are no tangles, kinks or that the tube is blocked with water

3.    Replace and flush with distilled water (TDS<3) water in the tank and start it again

4.    Contact your Sales Support Team

Imbalance error

| 1.  Unit has been tilted more than 30

degrees and will return an imbalance error

| 1. Place machine on a level surface and restart the machine.

Abnormal display value

| 1.    Scale formation in electrolytic cell

2.    The display is abnormal

3.    The TDS value is too high

| ****

1. Contact your Sales Support Team – 1800 268 469

Alarm sound

| ****

1.    Water level is low, or

2.    Water level too high

| 1.    Add more distilled water (TDS<3) or

2.    Drain out water from the tank until the water level is below the top (Max) mark on the water viewing panel

Screen blank

| 1.    Screen saver mode

2.    Machine is not turned on

| 1.    Press the setting icon

2.    Turn on power

If you run into any other problems, contact your AlkaWay Sales Support Team on 1800 268 469 or email us at info@alkaway.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>