Altronix eBridge4PCRM eBridge1PCTX Transceiver or eBridge1ST Mini Transceiver Installation Guide
- June 4, 2024
- Altronix
Table of Contents
Altronix eBridge4PCRM eBridge1PCTX Transceiver or eBridge1ST Mini
Transceiver
Overview
Altronix eBridge4PCRM and eBridge1PCTX or eBridge1ST are CAT5 to Coax cable Ethernet adapters/Media converters that deliver data and power over the coax cable in a PoE+ compliant format. The paired set enables fast 10/100Base-T Ethernet digital communication to be transmitted over Coax cable. eBridge4PCRM receiver is powered by a UL Listed limited power source, PoE midspan or endspan product, such as a NetWay8M and NetWay16M, and sends its power over the coax to the bridge 1PCTX or eBridge1ST transmitter under PoE protocol. This enables eBridge4PCRM to be used in a managed manner, allowing for remote camera reset. eBridge1PCTX or eBridge1ST, in turn, delivers that PoE+ compliant power to a PoE-enabled camera or IP device. eBridge4PCRM will not deliver power to non-compliant devices, thus avoiding damage to improperly connected analog cameras. These plug-and-play units facilitate system upgrades from analog to IP cameras/devices utilizing existing legacy Coax and eliminating the costs and labor associated with installing new network cabling. In addition, data transmission and power over the Coax is possible up to 500m in comparison to 100m Ethernet maximum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 6). A maximum range from the head end to the PoE camera/device is 700m, taking into consideration that up to 100m of structured cable may be deployed at each end.
Agency Listings:
- UL 60950- 1 Information Technology Equipment.
- CE European Conformity.
- C-Tick C-Tick compliant
Compatible Transceivers:
- eBridge1PCTX: PoE/PoE+ compliant transceiver.
- eBridge1ST: PoE/PoE+ compliant mini transceiver.
Input:
- Powered by a UL Listed limited power source,
- PoE midspan or endspan.
Ethernet:
- Connectivity: RJ45, auto-crossover.
- Wire type: 4-pair CAT5 or better-structured cable.
- Distance: up to 100m.
- Speed: 10/100BaseT, half/full duplex, auto negotiation.
- PoE compliant to IEEE 802.3af (15W) and
- PoE+ compliant to IEEE 802.3at (30W) delivered to camera by eBridge1PCTX or eBridge1ST.
- Power is provided by eBridge4PCRM to eBridge1PCTX or eBridge1ST by PoE protocol.
- Throughput is rated to pass 25Mbps of data at distances up to 500m. With proper headend equipment, this supports Megapixel, HD720, HD1080
Coax:
- Distance: up to 500m (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 6) for power delivery of coax.
- Connectivity: BNC, RG-59/U or similar
LED Indicators
eBridge4PCRM:
Blue LED – Coax link connection.
Green – PoE ON.
Green – Power ON.
eBridge4PCRM and eBridge1PCTX:
Yellow and Green LED (RJ45) IP Link status, 10/100Base-T/active.
eBridge1PCTX and eBridge1ST:
Blue LED – Coax link connection.
Green LED – PoE from eBridge4PCRM
Environmental:
- Operating Temperature:
- eBridge4PCRM: – 20ºC to 49ºC (– 4ºF to 120.2ºF).
- eBridge1PCTX:
- For 15W : – 40ºC to 75ºC (– 40ºF to 167ºF).
- For 30W : – 40ºC to 49ºC (– 40ºF to 120.2ºF).
- eBridge1ST:
- For 15W : – 40ºC to 75ºC (– 40ºF to 167ºF).
- For 30W : – 40ºC to 65ºC (– 40ºF to 149ºF).
- Storage Temperature : – 30º to 70ºC (– 22º to 158ºF).
- Humidity: 20 to 85%, non-condensing.
Functions:
- Auto detection and protection of legacy non-PoE cameras/devices.
Applications:
- Retrofit digital IP cameras in an analog
CCTV installation.
- Works with Megapixel, HD720, HD1080, and VGA (SD) cameras (see a note, ).
- Extend Network link distance in an industrial environment over 700m (see a note,).
- Upgrade deployed CCTV Coax to a digital network in Retail, Hospitality, Arenas, Casinos, Airports, Schools, Hospitals, Transportation, etc
Mechanical:
- Dimensions (H x W x D approx.):
- eBridge4PCRM dimensions: 1.7” x 5.23” x 8.42” (43.2mm x 132.8mm x 213.9mm)
- eBridge1PCTX dimensions: 1” x 2.5” x 4.375” (25.4mm x 63.5mm x 111.1mm).
- eBridge1ST dimensions: 2.27” x 2.645” x 1.12” (57.7mm x 67.2mm x 28.4mm).
Installation Instructions
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. eBridge1PCTX, eBridge1ST, and eBridge4PCRM are not intended to be connected to outside plant leads and should be installed indoors within the protected premises. eBridge1PCTX, eBridge1ST, and eBridge4PCRM are intended for indoor use only.
- eBridge4PCRM installation:
- Affix rubber pads to eBridge4PCRM for shelf installation (Fig. 5, ).
- The unit should be mounted in proximity to an ethernet switch/network, NVR or video server.
- Connect the structured cable from the ethernet midspan or endspan device to RJ45 jack marked [10/100BaseT](Fig. 2, ).
- Connect Coax cable to BNC connector marked [Coax] (Fig. 1,).
- eBridge1PCTX installation:
- Secure unit to the desired mounting surface with a proper fastening device utilizing the case’s mounting hole. The unit should be mounted in proximity of the camera/device.
- Connect structured cable from IP camera/device to RJ45 jack marked [10/100BaseT] (Fig. 2,).
- Connect Coax cable to BNC connector marked [Coax] (Fig. 2, pg. 4).
- eBridge1ST installation:
- Secure unit to the desired mounting surface with a proper fastening device utilizing the case’s mounting hole (Fig. 3, ). Unit should be mounted in proximity of camera/device.
- Connect the structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 3, ).
- Connect Coax cable from eBridge4PCRM to BNC tether cable marked [Coax] (Fig. 3,).
Note : eBridge4PCRM is designed to accommodate Megapixel, HD720, HD1080 and VGA (SD) cameras. It is important to note that some high resolution and high frame rate cameras may demand faster headend processing ability, such as a PC graphics card to present a quality image. If the headend processing equipment is insufficient in speed, the image may show pixelation and latency. It is advisable to pre-test system if unsure. Alternatively, frame rate and resolution may be reduced to accommodate system equipment.
Technical Specifications
| Parameter | Description |
|---|---|
| Connections | BNC for Coax link. RJ45 for ethernet link. |
| Input power requirements | Midspan or endspan port connected. |
Indicators
| Blue: Coax Link.
Yellow (RJ45 connector): On – Link, Off – No Link, Blinking – Activity.
Green (RJ45 connector): On – 100Base-TX, Off – 10Base-T.
Green: Power.
Environmental Conditions
| Operating Ambient Temperature: UL60950-1
eBridge4PCRM: – 20ºC to 49ºC (-4ºF to 120.2ºF).
eBridge1PCTX: For 15W: – 40ºC to 75ºC (– 40ºF to 167ºF).
For 30W: – 40ºC to 49ºC (– 40ºF to 120.2ºF).
eBridge1ST: For 15W: – 40ºC to 75ºC (– 40ºF to 167ºF).
For 30W: – 40ºC to 65ºC (– 40ºF to 149ºF).
Storage Temperature: – 30ºC to 70ºC (– 22ºF to 158ºF).
Relative Humidity: 20 to 85%, non-condensing.
Operating Altitude: – 304.8 to 2,000m.
Regulatory Compliance| UL/cUL Listed for Information Technology Equipment (UL
60950-1). CE European Conformity. C-Tick compliant.
Weights (approx.)| Product: 1.35 lb. (0.61 kg) | Shipping: 1.7 lb. (0.77 kg)
Multiple PoE Camera Connection
Maximum Length of Coax Type vs. Camera Power/PoE Class:
Camera Power/ PoE Class
| Coax Type
---|---
RG59/U – 23AWG| RG59/U – 22AWG| RG59/U – 20AWG| RG59/U – 18AWG| RG6/U – 18AWG
Max. Length (meters)
13W/0| 261| 336| 500| 500| 500
4W/1| 500| 500| 500| 500| 500
6.5W/2| 500| 500| 500| 500| 500
13W/3| 261| 336| 500| 500| 500
19W| 153| 199| 316| 500| 500
25W| 119| 152| 240| 366| 366
eBridge4PCRM Chassis Mechanical Drawing & Dimensions (H x W x D approx.):
1.7” x 5.23” x 8.42” (43.2mm x 132.8mm x 213.9mm)
Shelf Installation
- Position and affix rubber pads (included) at each corner on the bottom of the unit (Fig. 5).
- Place unit in desired location.
Altronix is not responsible for any typographical errors. 140 58th Street,
Brooklyn, New York 11220 USA |
718-567-8181 | fax:
718-567-9056
website: www.altronix.com | e-mail:
info@altronix.com | Lifetime Warranty IIeBridge4PCRM G15U
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>