OBA SP017 VLX10 Ip camera 2 megapixel P2P Free Bullet Modello User Manual

: June 9, 2024
: OBA

Table of Contents

SP017 VLX10 Ip camera 2 megapixel P2P Free Bullet Modello
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SP017 VLX10 Ip camera 2 megapixel P2P Free Bullet Modello

IP Camera

Quick User Manual

© OBA Srl
VIA LEPANTO, 132 – 80045 POMPEI (NA) – ITALY P.IVA e
C:F.: 07750391216

Customer Service
© OBA Srl
VIA LEPANTO, 132 – 80045 POMPEI (NA) – ITALY P.IVA e
C:F.: 07750391216

Products Introduction

Before starting setup

Make sure of the followings:
– Mount the antenna in vertical position (only for outdoor cameras).
– If your cameras are 2.4GHz WiFi, your phone must be connected to 2.4GHz WiFi.
– Check that DHCP on the router is enabled.
– For videos on how to set up our cameras, please visit: www.sricam.com/srihome/videos

Step1. SriHome App Installation
Scan the QR code to download “SriHome” App.
Search for “SriHome” on Google Play Method 1: or iOS App Store.
Method 2:

Step2. Registration & Login on SriHome App
Step3. Connect the camera to the network

Product Connection with cable

Step1-1: Connect the camera to LAN (Router or Switch) via network cable.
Step1-3: Reset the came(Krae.ep pressing the RESET button for 8 seconds then release.)
Step3. Register an App account and Login
Step1-2: Power on the camera with power adaptor.

Note: If no LAN port on your router, you can connect the camera to Wi-Fi via4 AP
Hotspot.
Details please reference to FAQ7.

Step2. SriHome App Installation
Method 1: Scan the QR code to download “SriHome” App.
Method 2: Search“SriHome”on Google Play or iOS App Store.

Step3. Register an App account and Login

Step4. Add the Camera to App

Step5. Connect the camera to Wi-Fi

Settings -> Network Settings ->Choose WiFi ->Confirm ->Enter WiFi password ->
Confirm->Save. (as figure 5-1 to 5-6)

Unplug the camera from Ethernet and power, then relocate the camera to anywhere
within range of the WiFi network that you connected the camera to.

Product Connection wifi without cable

1. Turn on the camera
The camera will emit a continuous “beep” after 30 seconds.
Note: If there is no “beep” sound,
keep holding the “RESET” button for 5 seconds until you hear a long “Beep”

2. Add the camera to the APP
When you hear the continuous “beep”, follow the instructions of the SriHome APP to add the device, as in the figure:

Introduction for monitoring interface:

1. App Settings
2. Scan code
3. Split Screen
4. Add SD
5. Settings
6. Full screen
7. Up & down
8. Resolution
9. Local record
10. Screenshots
11. Speaker
12. Microphone

Trouble shooting:

– If you are unable to add a device on the app, please make sure the following:
1. Before adding a device, you will hear continuous “beeps”
(if there is no sound, RESET the device)
2. Enter the correct Wi-Fi password. (It is recommended that wireless passwords do
not use special characters !”£%
3. When you hear the “beep” sound, click “Next” in step 3-4.
– If the device could not be added to the “SriHome” app via “WiFi QR Connect” for
many times, please refer to FAQ1 “WiFi Hotspot Connect” on page 4 to add the device

FAQ1: How to add camera to app via WiFi Hotspot

Notice: Before using the WiFi hotspot to add the device in the app, you need to turn off the
3G / 4G / LTE mobile data of the smarphone first.

Step 1: Connect your phone to the camera’s WiFi hotspot

1). Turn on the device and wait 30 seconds, the camera will generate a WiFi hotspot:
Camera WiFi SSID: IPC _ **, WiFi Password: 12345678
2). Go to your phone’s WLAN settings and connect your phone to the camera’s WiFi hotspot

Note: If the camera’s WiFi hotspot is not found in the phone’s AVAILABLE NETWORKS list, please reset to factory settings and try again.

Step 2: Add the device to the App

Open the “SriHome” App, tap “+”, follow the instructions to add the device.

FAQ2: Share the camera with other users
To protect the user’s privacy, the first user is an administrator by default. Other users accessing the camera need administrator permission, or they cannot log in even with ID and password.
The way to get permission is as follows:
Access the “SriHome” App, tap Settings -> Visitor Management -> Add.
There are 2 types of permissions:
Operator: Live video view, set time, alarm, record and network.
Visitor: Viewing video only in real time
Note: You can find the user’s App ID in App Settings

FAQs:
1. How to set up recordings on micro SD.
2. How to add the camera on your second phone.
3. How to set the motion detection alarm.
4. The camera does not detect the micro SD.
5. Multi-view on srihome App.
6. The camera’s Wi-Fi is unstable and often offline.

If want to know more, please visit YouTube: SriHome IPC

More FAQs Please visit: www.sricam.com/srihome/faq

www.obasecurity.it