OTAONEOTA C6497 LED Electric Callus Remover User Manual
- June 9, 2024
- OTAONEOTA
Table of Contents
OTAONEOTA C6497 LED Electric Callus Remover
PRODUCT STRUCTURE INTRODUCTION
- A. Switch
- B. Body
- C. speed display
- D. Power display
- E. Grinding head
- F. charging interface
- G. USB charging cable
- H. cleaning brush
PRECAUTIONS
Before using the product, please read this manual carefully and keep it for future reference.
- This electrical product cannot be used as a toy for young children.
- Children and disabled people need the guidance of adults.
- This product can only be used as a household appliance, not for industrial use.
- This product cannot be used in special environments such as corrosive or explosive gases.
- This product cannot be used as a medical appliance.
- Do not disassemble, repair, or modify the product without permission.
- Do not store in direct sunlight or where the storage environment is too hot or humid.
- If the power cord is damaged, it must be replaced with a special component purchased from its manufacturer or repair department.
- When charging, please keep away from the water source, and do not charge near water-filled baths, tubs or other liquid containers. After charging is complete, unplug it immediately.
- Please use this product within the description requirements of this manual, and do not use accessories not recommended by the manufacturer.
- Do not throw this product or any foreign objects into the charging socket connector, so that the product is damaged and cannot be used.
- Do not immerse the charging cable in water or other liquids, and do not rinse it under the faucet.
- Do not soak the product in water for a long time.
- The grinding head is only suitable for calluses, hard and thick dead skin, such as heels, please do not use this product on normal skin areas.
- For hygienic reasons, it is recommended that each quartz grinding wheel be used by only one person, preferably not shared with others.
- If you have any skin problems or other medical problems, please use after consulting your doctor.
- When using, do not stay on one skin area for more than 3 seconds, use it while moving.
- Do not use on red, inflamed, infected or blistered skin.
- Do not use this product on warts, ulcers or wounds on the skin.
- Stop use immediately if you experience any pain or discomfort. Excessive use of the microdermabrasion tip will cause the skin to be too thin and easily cause skin irritation. If the skin is severely allergic or bleeding, please seek medical attention in time.
- In order to prevent accidents and damage to your body, please keep away from your scalp, hair, eyebrows, eyelashes and clothes, wool, shoelaces, etc. when using microdermabrasion.
- WARNING Do not wash the hand-held part in water until the hand-held part is separated from the power cord.
INSTRUCTIONS
CHARGE
Note: Please fully charge the product before using it for the first time.
Charging steps: Insert one end of the USB cable into the charging hole of the
fuselage, and connect the other end to the mobile phone charger or computer
USB jack, etc., the USB output end, the charging indicator light is on,
charging for 5 hours, the indicator light stops flashing and charging is
complete (charging time). no more than 12 hours).
ASSEMBLING AND DISASSEMBLING GRINDING HEADS
Replace the grinding head according to the following operations. The selection
and replacement of the grinding head can be based on the roughness of the skin
used and the expected effect. Before replacing the grinding head, make sure
that the power supply is disconnected and the machine is turned off.
-
How to replace the grinding head? Hold the handle of the product with one hand, pull the old grinding head out at this postion(See Figure 1 and Figure 2). press the new grinding head for replacement with the other hand, until you hear a ‘click’ sound, which mean the installation is OK (See Figure 3). Make sure that the newly installed grinding head is locked in place. If the grinding head is not connected properly, do not turn on the product switch.
Note: When unpacking the product, 1 grinding head has been installed on the body. -
How to open the machine cover? After taking off the grinding head, hold the handle of the product with one hand, rotate the cover for a little(See Figure 4), until the Postion 1 align at Position 2(See Figure 5), and then pull the cover out of the product(See Figure 6).
GRIND CALLUSES
- This product is desigrned for use on dry, rough feet or heels.
- Do not use on other parts of the body.
-
Ensure that the product has sufficient power.
-
Make sure that the quartz grinding head has been installed on the product. If you remove and replace the grinding head, please refer to the previous section to prepare for use.
-
Clean or soften the skin and dry the moisture from the area of application to ensure the best results. Note: Do not use if there is a wound or bleeding on the skin.
-
Press and hold the switch for 3 seconds to turn on
-
Gently rotate the head and leave on dry rough skin area for 2-3 seconds. Don’t press too hard, let the grinding head gently slide over the skin. If you press it too tightly or use too much force, the product will stop using (over resistance protection function). During use, you can stop to check whether the keratin removal is satisfactory. If not, you can use it again on this area (for 2-3 seconds) and check again. Until smooth and delicate skin is reproduced.
Warning:Discontinue use immediately if skin becomes sore or inflamed.
Warning:Do not use on skin for longer than 2-3 seconds. -
After use, please shut down.
-
Rinse the skin or use a damp towel to remove excess cuticles.
-
After use, clean up the product in time. See cleaning section.
-
Please store the product in a dry, ventilated and cool place.
Manual Pedicure Tools
Steps of Foot Spa Soak your feet or other areas of callused skin in warm water (perfect for use in a shower). After rubbing, rinse your feet with cool water and wash the scrubber and then apply a soothing lotion.
-
Nail File
Double sided emery boards: file and rough up the hard fingernails and toe nails, smoothing up your nail edge with refined shape. -
Callus Remover
It’s high quality stainless steel surface with appropriate balde sharpness works instantly to shave off layers of dried calluses. -
Foot File
Use the tool with blade side, move forward and backward to file away the callus, do not use to much strength in case of hurting the skin. -
V-shaped Push Stick
The dead skin push is 45° to the nail surface. Putting it too high may cause it to be unable to push or press to the back edge of the nail. Putting it too flat will easily damage the nail and skin directly. When pushing the dead skin, the force must be light and the technique must be gentle. -
Double-sided Frosted File
Gently rub your feet, heels, or palms with the foot scraper.
CLEAN AND MAINTENANCE
- Remove the grinding head and use a brush to remove horny debris from the foot grinder.
- The grinding head can be washed with water alone to remove cuticles. When finished, dry the machine with a cloth. This machine can be washed all over the body.
Note:Before cleaning, make sure the machine is turned off and the charging cable and socket are not connected.
THREE KIND OF GRINDING HEADS
- Fine grinding head: suitable for hand calluses, raised dead skin and more delicate skin care.
- Medium grinding head: suitable for the care of calluses that have just formed and normal skin.
- Coarse grinding head: suitable for thick calluses accumulated over the years and the care of thicker skin.
TECHNICAL PARAMETER
- Product name: Electric foot grinder
- Charging voltage: 5V
- Charging Current: 0.7A
- Charging power: 3.5W
- Working voltage: 3.2V-4.2V
- Working current: 2A
- Working power: 6.4W-8.4W
Please keep this manual in a safe place.
Remarks: Suitable for cleaning under open faucets
ENVIRONMENTAL PROTECTION AND RECYCLING
The built-in rechargeable battery contains substances that pollute the environment. When you decide to dispose of this product, please remove the battery and dispose of the battery toa government-regulated place or recycling unit.
- Turn on the foot grinder switch until the foot grinder stops working and drains the battery.
- Before disassembling the foot grinder and taking out the battery, you must tum off the switch and disconnect the power supply.
- After removing the battery, never connect the foot grinder to the charger, and be careful not to short-circuit the positive and negative poles of the battery.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>