Nakamichi Shockwafe Elite 7.2 SSE 800W Soundbar System User Manual

USER MANUAL

IMPORTANT SAFETY INSTRUCTIONS

Your Unit is designed and manufactured to operate within defined design limits, and misuse may result in electric shock or fire. To prevent your Unit from being damaged, the following rules should be observed for its installation, use, and maintenance. Please read the following safety instructions before operating your Unit. Keep these Instructions in a safe place for future reference.

• Read these Instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with a dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturers instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

• Only use attachments/accessories specified by the manufacturer.

• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

• To reduce the risk of electric shock or component damage, switch off the power before connecting other components to your Unit.

• Unplug the power cord before cleaning your Unit. A damp cloth is sufficient for cleaning. Do not use a liquid or a spray cleaner on your Unit. Do not use abrasive cleaners. • Always use the accessories recommended by the manufacturer to insure compatibility.

• When moving your Unit from an area of low temperature to an area of high temperature, condensa-tion may form In the housing. Wait before turning on your Unit to avoid causing fire, electric shock, or component damage.

• Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of your Unit and to protect it from overheating, be sure these openings are not blocked or covered. Do not place your Unit in a bookcase or cabinet unless proper ventilation Is provided.

• Never push any object into the slots and openings on your Unit enclosure. Do not place any objects on the top of your Unit. Doing so could short circuit parts causing a fire or electric shock. Never spill liquids on your Unit.

• When connected to a power outlet, power is always flowing into your Unit. To totally disconnect power, unplug the power cord.

• Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
  • The wall socket should be located near your Unit and be easily accessible.

• Keep your Unit away from moisture. Do not expose your Unit to rain or moisture. If water penetrates into your Unit, unplug the power cord and contact your dealer. Continuous use in this case may result in fire or electric shock.

• Do not use your Unit if any abnormality occurs. If any smoke or odor becomes apparent, unplug the power cord and contact your dealer immediately. Do not try to repair your unit yourself.

• Avoid using dropped or damaged appliances. If your Unit is dropped and the housing is damaged, the intemal components may function abnormally. Unplug the power cord immediately and contact your dealer for repair.

• Continued use of your Unit may cause fire or electric shock.

• Do not install your Unit in an area with heavy dust or high humidity. Operating your Unit in environments with heavy dust or high humidity may cause fire or electric shock.

• Ensure that the power cord and any other cables are unplugged before moving your Unit.

• When unplugging your Unit, hold the power plug, not the cord. Pulling on the power cord may damage the wires inside the cord and cause fire or electric shock. When your Unit will not be used for an extended period of time, unplug the power cord.

• To reduce risk of electric shock, do not touch the connector with wet hands.

• Insert the remote control batteries in accordance with instructions. Incorrect polarity may cause the battery to leak which can damage the remote control or injure the operator.

• The marking label of the subwoofer was located on the external bottom enclosure of the product.

• The equipment shall be used at maximum 35 degree Celsius ambient temperature.

• See the important note and rating located on the back of the unit.

• WARNING – This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near the equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain, or moisture.

• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

• CAUTION – Danger of explosion or fire if batteries are mistreated. Replace only with the same or specified type.

• Do not leave the batteries exposed to direct sunlight for a long period of time with doors and windows closed. Do not disassemble the batteries or dispose of it in fire. • Where the MAINS plug or appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

| This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerousvoltage within the product that may be sufficient magnitude to constitute a risk of shock to persons.
---|---
| The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operatic and servicing instructions in the literature accompanying the appliance
****| Warning:  This equipment is a Class II or double insulated electrical appliances. It has been designed in such way that it does not require a safety connection to electrical earth.

PACKAGE CONRENTS

CONTROLS & CONNECTIONS

REMOTE CONTROL
A Remove the battery cover by pulling it down from the remote
B Insert the included batteries and gently push the battery cover back into place
REMOTE ANGLE
Tilt the remote downwards by 15-25 degrees for best response (as if you are aiming the remote slightly towards the ground)
! Once HDMI-CEC is set up, use your TV/content device’s remote control to power ON your soundbar.
Always use your TV’s remote control to power OFF the system.
DID YOU KNOW?
Once HDMI-CEC is set up, TV’s HDMI-CEC has taken control over soundbar’s remote ON/OFF and other functions. Those functions will not longer work on the soundbar remote.

SETTING UP YOUR HOME THEATEF

SPEAKER PLACEMENTS
OPTION A (BEST): 7.2CH SURROUND
Recommended speaker placement with optimal distance. Actual distance can vary based on actual room layout.
The bottom speaker driver of the surround speakers should be at ear level and pointing directly at the listener’s sitting area for optimal performance. Note: Illustration is not to scale. Speaker stands are not included.

For recommended speaker stands, scan QR code or visit:

bit.ly/72-speaker-stands

OPTION B: ALL ELEVATION
Lay the surround speakers down (drivers tilted upward in 2 modes, see illustration on the right) to enhance the vertical effects to bounce off the ceiling o f your room.

Note: Recommended speaker placement with optimal distance.
Actual distance can vary based on actual room layout.

CONNECTING SURROUND SPEAKERS T0 SUBWOOFERS
Connect SURROUND SPEAKERS to the ports on the back panel o f SUBWOOFERS using the included surround speaker audio cables

TURNING ON YOUR SOUNDBAR SYSTEM

Note: Once soundbar is powered o f f , the blue LED lights on the subwoofers will continue blinking for 10 minutes before going into standby mode.

CONNECTING YOUR TV
Options for connecting your TV: HDMI OPTICAL . COAXIAL (See next page)

1. Connect one end o f the HDMI cable to the HDMI (ARC) port at the back o f your TV.
2. Connect the other end to the HDMI OUT [1] (ARC TO TV) port to your Nakamichi soundbar.

DID YOU KNOW?
HDMI Audio Return Channel (ARC) sends audio from the TV to our soundbar

Back of Soundbar

Note: Be sure t o connect to a TV’s audio output port, not an audio input port.

• Not all TVs have the audio outputs shown above. To connect the soundbar directly to your other devices (Blu-ray player, game system, etc.). See page 20 CONNECTING YOUR CONTENT DEVICES
• Cable appearance may differ from the ones s upplied.
  If there is no audio during the setup, see page 37 for Help & Troubleshooting
  + Cable not included

LISTENING TO YOUR SOUNDBAR

For expanded remote control guide, scan QR code or visit:

DID YOU KNOW?
Dolby Atmos is the latest Dolby’s object-based 3D surround sound format. It is encoded into Dolby TrueHD or Dolby Digital Plus stream with metadata to extract and place the objects in relevant positions.

SETTING UP YOUR TV
All units sold since Aug 2019 can receive Dolby Atmos surround via TV’s eARC when streaming with TV’s smart apps like Netflix (Note: not all TVs can output Atmos.)
What is HDMI Audio Return Channel (ARC)?
Using HDMI ARC, y o u r TV can send audio to the soundbar using a HDMI cable. You will need to connect your soundbar to your TV’s HDMI ARC port using a high speed HDMI 2.0 cable.
Audio settings for TV*
Setting the audio output:
A) Go to Settings > Sound
B ) Select Speaker Settings
C) Set as HDMI Audio Out
Setting the audio format:
A) Go to Settings > Sound > Additional Settings
B ) Select Audio Format
C) Set as Dolby Digital / DTS / Bitstream (whichever is available)

What is CEC?
CEC is a HDMI protocol that is only available when: 1. Your TV is CEC enabled. (Check with your TV manufacturer for more information) 2. The soundbar and TV is connected via a HDMI cable through the ARC ports. By doing so, you are able to control the soundbar’s volume and power functions with the TV remote. Enabling CECt From the SYSTEM menu, enable CEC and ARC (SAC)1. functions.
From the CEC menu, select Device Discovery to register the soundbar with the TV.
Enable CEC forty only. Do not enable CEC for other source devices or inputs may switch randomly. To disable CEC for the soundbar, see page 25.

• Steps may differ based on TV brand. See your TV’s user manual for more information.
  HDMI-CEC TVTrade names: Samsung (Anynet+), Sharp (Aquas Link), Sony (Bravia Sync), LG (SIMPLINK), Panasonic (HDAVI Control / EZ Sync /Vera Link), Philips (EasyLink),Vizio (CEC), Hitachi (HDMI-CEC). Naming may differ based on TV brand. See your TV’s user manual for more information.

Visit nakamichi-usa.com/best-sound for expanded list of TVs’ audio settings instructions. Visit bit.ly/hdmi-cec- settings or scan QR Code for HDMI-CEC setup instructions by device
If your devices are not listed on our website, please check with the device manufacturer’s manual

https://bit.ly/hdmi-cec-settings

CONNECTING YOUR CONTENT DEVICES HDMI CONNECTION SETUP
! Use our “Perfect Device Matching Tool” to create a custom setup guide based on your TV and devices. Scan OR code or visit bittyldevice-matching-tool

https://bit.ly/plug-play-matching- tool

! Connect devices with the same HDCP standards for seamless switching between sources. If there are devices with different HDCP standards, connect all HPCP 2.2 devices to soundbar while connecting HDCP 1.4/2.0/2.1 devices to TV to avoid audio and video instability.

• Cables may appear differently from the ones supplied.

CONNECTING YOUR CONTENT DEVICES (CONT.)
NON-HDMI CONNECTION SETUP

Use our -Perfect Device Matching Tool to create a custom setup guide based on yourTV and devices. Scan UR code or visit bit.ly/device-matching- tool

https://bit.ly/plug-play-matching- tool

! Dolby Atmos and DTS:X audio are not supported on Optical, Coaxial and Aux connections

CONNECTING YOUR CONTENT DEVICES ADVANCED SETUP – FOUR-DEVICE SETUP FOR HDTV

use our -Perfect Device Matching Tool-to create a custom setup guide based on your W and devices. Scan DR code or visit bi.tty/device-matching- tool

https://bit.ly/plug-play-matching-tool

CONNECTING YOUR CONTENT DEVICES (CONT.)
ADVANCED SETUP – FOUR-DEVICE SETUP FOR TV WITHOUT HDMI ARC

CONNECTING YOUR CONTENT DEVICES CONNECTIONS CENTRAL – RECOMMENDED CONNECTION BASED ON DEVICES

! If you are using Optical connection option, connect all your content devices to TV.

SETTING UP YOUR CONTENT DEVICES
RECOMMENDED AUDIO SETTINGS FOR BEST AUDIO

APPLE TV® 4K (5th Gen)
Setting Audio Output:
Settings > Video and Audio > Audio > Audio Output > select HDMI
Setting Audio Format:
Settings > Video and Audio > Audio >

1. Audio Mode > select Auto
2. Reduced Loud Sounds > select OFF
3. Audio Format >
   A. Change F o r m a t > select OFF
   B. Dolby Atmos > select ON

A PPLE TV® (4th Gen}
Setting Audio Output:
Settings > Video and Audio > Audio > Audio Output > select Apple TV
Setting Audio Format:
Settings > Video and Audio > Audio > Surround Sound > select Dolby
Digital 5.1

AMAZON FIRE® TV CUBE / FIRE® TV 4K
Settings > Display & Sounds > Audio > select Dolby Digital Plus over HDMI
NOTE: When plugging F i r e TV 4K directly to TV, set TV audio’s digital output format > select Dolby Digital
ROKU™ ULTRA 4K / ROKU™ 4/ ROKU™ 3
Setting Audlo Format:
Roku Ultra 4K: Settings > Sound > HDMI > select Dofby D+, DTS (Required for Netflix, Amazon and Hulu streaming)
Roku 4 and 3 : Settings > Audio > Audio Mode > select DD/DTS ROKU™ MEDIA STICK
Recommended Setup: Connect the device directly to TV via HDMI port and send out audio to soundbar via ARG

Setting Audio Format:

1. ROKU Audio Settings: Settings > Sound > HDMI > select Dolby D+, DTS (Required for Netflix, Amazon and Hulu streaming)
2. TV Audio Settings: Digital Output Format > select Do/by Digital

NVIDIA® SHIELD
Setting Audlo Format:

1. Nvidia Shield Audio Settings: Settings > Display & Sound > Other > Advanced Settings >
   a . Stereo Upmix > tum On (For 2015 model only)
   b . HDMI 5.1 Audio > turn On (For 2017 model only)

PLAYSTATION® 4 PRO
Setting Audio Output:
Settings > Sound and Screen > Audio Output Settings > Primary Output Port > select HDMI Out (Uncheck Output 5.1ch Audio box to allow 7.1ch Audio output)

Setting Audio Format:

1. System Level Audio Settings:
   Settings > Sound and Screen > Audio Output Settings > Audio Format (Priority)

   select Dofby Digital (Best for Netflix streaming)

2. Blu-ray Player Audio Settings: (Available when playing Blu-ray disc) Press Option button on controller > Settings > audio format > select Bitstream (Direct)

XBOX” ONE X
Setting Audlo Format:

1. System Level Audio Settings:
   System > Settings > Display & Sound > Audio Output > Speaker Audio >
   a. HDMI Audio > select Bitstream Out
   b . Bitstream Format > select Dolby Atmos for Home Theater

2. Blu-ray Playback Audio Settings:
   Settings > Disc & Blu-ray > Blu-ray >
   a. Let my receiver decode audio > Enable (Check the b o x )
   b . Pass Blu-ray audio directly to your receiver? > select Pass audio to receiver

NINTENDO® SWITCH
Recommended Setup: Connect the device directly to TV via HDMI port and send out audio to soundbar via ARC
Setting Audlo Format: (Put the console in TV mode)

1. SWITCH Audio Settings:System Settings > TV Settings > TV Sound > Automatic
2. TV Audio Settings: Digital Output Format > select Dofby Digital

Above i s the recommended audio settings for a list of popular devices.
For full list of devices with our recommended audio settings, visit nakamichi-usa.com/best-sound or scan QR code on the right.

https://bit.ly/plug-play-matching-tool

REMOTE CONTROL OVERVIEW

1. POWER
Turn ON/OFF the soundbar
2. PLAY/PAUSE **
Play/pause audio playback (Bluetooth/USB mode only)
3. STOP ■
Stop audio playback (Bluetooth/USB mode only)
4. INPUT SOURCE
Select an audio input source (See page 23 for more details)
5. SYSTEM MEMORY
Save your personalized audio settings (See page 31 for details)
6. EQ (EQUALIZER)
Select different audio equalization presets (See page 24 for details)
7. STEREO ONLY
Activate All Channel Stereo or Stereo Only
8. SETUP
Access to advanced system settings (HDMI ARC/2/3/4 mode only, see page 25)
9.  BUTTON
Toggle different settings (SETUP/MENU function only)
10. ENTER BUTTON
Select desired settings (SETUP/MENU function only)
11. RETURN
Return to the previous selection (SETUP/MENU function only)
12. BASS + / –
Adjust the bass level
13. CENTER + / –
Adjust the center channel level
14. SS + / – (SURROUND SIDE)
Adjust the volume of both side surround channels
15. SB + / –
(SURROUND BACK)
Adjust the volume of both back surround channels| 16. MUTE
Mute/unmute the soundbar
17. NEXT
Skip to the next track (Bluetooth/USB mode only)
18. PREVIOUS
Return to the previous track (Bluetooth/USB mode only)
19. NIGHT
Normalize volume for night time listening
(Dolby/DTS:X audio only, see page 24 for details)
20. DIRECT
Select different channel mapping/upmixing methods (See page 26 for details
21. MENU
a Access to Firmware upgrade and wireless subwoofer pairing (USB mode only, see page 27 for details)
22. SSE + / –
(SPATIAL SURROUND ELEVATION PROCESSING)
Select different SSE modes (See page 28 for details)
23. INFO ■
Display system information on the soundbar LED display (See page 29 for details)
24. ROOM SIZE
Select a pre-defined optimized room size (See page 30 for details)
25. VOL + / – (VOLUME)
Adjust the master volume of the soundbar
26. LED DISPLAY
Select between 3 pre-defined brightness for the front LED Display. (DIM 0 = Display light will shut off automatically)
27. TR + / – (TREBLE) Adjust the high tones (treble) level
28. + / – (LIP SYNC)
Adjust the deviations in timing between audio and video playback (HDMI 1 to 4, Optical or Coaxial input only, see page 41 for details)
29. SUR (SURROUND ON/OFF)
SUR:** All-channel surround sound
. Surround speakers will be disabled
---|---

• lf HDMI CEC is connected between TV and soundbar, always use the TV or source device’s power button on the remote t o power “ON” the system. Always use the TV power button t o power “OFF” the system.

SELECTING DIFFERENT INPUT SOURCES ON YOUR REMOTE
Press source buttons to select an audio input source.
Each input source will be displayed on the soundbar’s front LED display.

ACCESSING AUDIO PRESETS ON YOUR REMOTE

EQ (EQUALIZER)
Press the EQ buttons on your remote to select your desired EQ settings for your preference. The system will remember the last setting.

MUSIC| MUSIC| Creates the acoustic environment of your music and makes you feel like you are seated in front of the stage.
---|---|---
MOVIE| MOVIE| Reproduces the thrilling environment and takes you to the center of the action. Feel the dynamic excitement.
GAME| GAME| Reproduces sound field effects for all game genres and adds depth and spaciousness to your game’s surround sound
NEWS| Makes you feel like you are in the front row of a live talk show. Hear crystal clear dialog.
SPORTS| Reproduces the energetic environment of live sports broadcasts. Place the commentator’s voice center stage and lets the sounds that fill the stadium surround you.
CLEAR VOICE| CLEAR VOICE| Enhances the clarity of dialog playback.
DSP OFF| DSP OFF| Audio playback without using any pre-defined Nakamichi EQ settings.
MUSIC|
---|---
MOVIE
GAME
NEWS
SPORTS
CLEAR VOICE
DSP OFF

NIGHT MODE
Night mode feature normalizes the overall volume t o avoid sudden changes in loudness.
This feature is available with DTS:X and DOLBY contents on HDMI, HDMI ARC, Optical and Coaxial inputs.

NIGHT| OFF (default)| Volume normalization OFF. Maximum audio impact on video content.
---|---|---
50%| 50% of volume normalization
100%| 100% of volume normalization, recommended for night time listening
AUTO| Contextual adaptive volume normalization to retain audio dynamism during normalization (For DOLBY content only)
DRC OFF|
---|---
DRC 50%
DRC 100%
DRC AUTO

ACCESSING ADVANCED SYSTEM SETTINGS ON YOUR REMOTE

(ONLY ACCESSIBLE ON
HDMI ARC/2/3/4 MODE}
To use SETUP function, switch to HDMI ARC/2/3/4 input.
SETUP function applies to all input sources.

1. Press the SETUP (%) button to cycle through different system settings.
2. Press ENTER to select desired function for adjustment.
3. Available actions:
   a. Press button to change the SELECTION value.*

• To select different settings or exit the SETUP function:
  a. Press RETURN button to quit the current action and back to SETUP list to select different set tings.
  b. Press SETUP button to exit SETUP function

  4. Press ENTER button t o save your settings value.

• CEC-OTP: HDMI-CEC ONE TOUCH PLAY is a HDMI function on the soundbar that automatically switches between HDMI sources.
  (e.g. auto switch to ARC mode when a TV is powered on ).
  By turning OFF the One Touch Play, you can manually select the input sources by using soundbar remote or Harmony universal remotes.

DTS:X & DOLBY
Dynamic Range
Compression (DRC)| DRC
(Default OFF)| OFF
50%
100%
AUTO
Power Saving| ECO
(Default ON)| OFF
ON
Subwoofer
Crossover Frequency| CROSS
(Default 180HZ)| 110HZ
140HZ
180HZ
Volume Balance for RIGHT Surround and Rear Speakers| RSURR
(Default 00)| -3 to +3
Volume Balance for LEFT Surround and Rear Speakers| LSURR
(Default 00)| -3 to +3
HDMI-CEC: One Touch Play| CEC-OTP
(Default ON)| OFF
ON
DTS:X Dialog Control
(For DTS:X content only)| DIALG
(Default +3)| DIA+1 to
DIA+6
Dedicated Frequency (D FRQ)| ON| DF ON**
OFF| DF OFF (Default)
Factory Reset (System will restart when selecting YES)| RESET| YES
NO

ACCESSING CHANNEL MAPPING/UPMIXING ON YOUR REMOTE
CHANNEL MAPPING
Channel mapping/upmixing is essential because most content is not recorded in 9.2 channels. The soundbar utilizes different channel mapping methods to optimize your listening experience. Dolby & DTS encode their own content with their respective proprietary upmixers to optimize surround performance.

Dolby Upmixing (Available for Dolby and PCM contents)

DIRECT| NATIVE| Direct decode 2.1/5.1/7.1 channel audio (No audio upmixing). Best for music and Bluetooth.
---|---|---
DOLBY UPMIX| Dolby technology upmixes audio content to all audio channels.
DOLBY SURR (DEFAULT)| Dolby technology upmixes audio content to all audio channels with vertical surround effects. (see page 41 for details)
NATIVE|
---|---
DOLBY UPMIX
DOLBY SURROUND

DTS Upmixing (Available for DTS content only)

DIRECT| NATIVE| Direct decode 2.1/5.1/7.1 channel audio (No audio upmixing). Best for music and Bluetooth.
---|---|---
DTS DIRECT| System DSP upmixes audio content to all audio channels.
NEURALX (DEFAULT)| DTS technology upmixes audio content to all audio channels. Set to NEURAL:X to receive audio from all rear speakers. (see page 40 for details)
NATIVE|
---|---
DTS DIRECT
NEUTAL: X

**ALL CHANNEL STEREO / STEREO ONLY Mode***

ALLCH STEREO| DTS, DOLBY & PCM| Enables 3 channel (Left, Center, Right) playback on the soundbar. Front channels are upmixed and outputted to surround speakers.
---|---|---
STEREO ONLY| DTS| Enables 2-channels stereo playback using the right front and left front channels. It down-mixes DTS multi-channel signals to 2 Channels.
DOLBY & PCM| Enables 3-channels (Left, Center, Right) playback using the right front, center and left front channels. It down-mixes Dolby & PCM multi-channel signals to 3 Channels.
ALL CH STEREO|
---|---
STEREO ONLY

Note: For Bluetooth input, ALL CH STEREO mode will be tumed ON by default.

• Available on latest firmware (FW35 onwards) only. See page 36 for instructions on checking firmware version and upgrading.

ACCESSING MENU FUNCTIONS ON YOUR REMOTE
(ONLY ACCESSIBLE ON USB MODE)

To use MENU function, please switch to USB input.
Navigating the MENU SELECTION:

1. Press the MENU ( ) button cycle through different function (FWUPG -> SUB PAIR)
   MENU| SELECTION| FUNCTIONS
   ---|---|---
   FIRMWARE UPGRADE (See page 37 for details)| FWUPG| UPGRADING
   DONE
   FAIL
   WIRELESS SUBWOOFER PAIRING (See page 34 for details)| SUB PAIR| PAIRING
   DONE
   FAIL

2. Available actions:
   a. Press button to change the SELECTION FUNCTIONS
   b. Press ENTER to select desired function.
   c. Press RETURN (4 ) button to quit the current action
   and back to MENU ( ) list to select different function
   d. Press MENU ( ) button to exit MENU ( ) function

3. Press ENTER to confirm

ACCESSING SSE MODE ON YOUR REMOTE
SPATIAL SURROUND ELEVATION (SSE) MODE
Shockwafe Elite 7.2 SSE is embedded with 3 proprietary advanced processing engines that unlock 7.2.4ch all-around surround effects
(SSE OFF = No vertical surround effects)

|
---|---

WHAT IS SSE PROCESSING?

Performs spatial-amplification techniques to unlock extra details, enhance directionality and enlarge spaciousness of
the surround sound experience| Executes upmixing, phase and volume improvements to optimize the clarity and balance
of the surround sound across all channels, delivering up to 7.2.4 channels| Enables the processing of all the latest 3D object-based content, including Dolby Atmos, and interlaces a height effects sound layer
| |

ACCESSING INFO ON YOUR REMOTE

** Xbox One X/S and Apple TV 4K come with a Dolby Atmos MAT encoder, which is designed t o encode, decode and incorporate Dolby Atmos metadata into lossless pulse-code modulation (PCM) audio, allowing listeners to experience Dolby Atmos even in PCM audio.

CCESSING ROOM SIZE ON YOUR REMOTE CCESSING ROOM SIZE ON YOUR REMOTE

ACCESSING ROOM SIZE ON YOUR REMOTE

For instant surround optimization to Small Medium and Large rooms, the re are 3 pre-tuned acoustic configurations.

SAVING AUDIO SETTINGS TO SYSTEM MEMORY

Customized Memory 2 Long press to SAVE2 Once saved, show M2SET

Two sets of audio settings can be saved onto the soundbar’s memory, allowing quick access to your audio preferences.

Saving settings to system memory:

1. Hold down the SYSTEM MEMORY 1 or 2 button until “SAVE1” or “SAVE2”, corresponding to the button pressed, is displayed on LED.
2. When the SYSTEM MEMORY 1 or 2 settings are saved, “Ml SET” or “M2SET” is displayed. If system settings are already stored in the selected memory 1 or 2, the system overwrites the old settings.

Loading settings

1. Press the SYSTEM MEMORY 1 or 2 button once and the corresponding settings will be loaded. If the SYSTEM MEMORY 1 button is pressed, “Ml” will be displayed.
   The following audio settings can be saved to system memory:
   a) EQ mode
   b) Volume
   c) Bass
   d) Treble
   e) Center
   f) Surround L&R
   g) Surround Back L&R

WIRELESS BLUETOOTH AUDIO STREAMING

BLUETOOTH 4.1 WITH APTX
Stream music wirelessly from your mobile device via Bluetooth (BT) with aptX. BT audio transmission is often compressed using bit-rate reduction. Qualcomm aptX audio technology uses larger transmission bandwidth to allow higher resolution audio streaming, reproducing pure sound as good as wired connection.

Maximizing Signal
A Bluetooth signal has a range of up to 30 feet. If you hear any break-up or disconnect while streaming music from your device, move the source device closer to the soundbar.
Note: Soundbar will be switched to ALL CHANNEL STEREO in Bluetooth mode.

Your soundbar is not equipped with a microphone, so it cannot operate as a hands-free device for a smartphone.
Reduce the volume levels on your device and on the soundbar before pressing Play. High volume levels

BLUETOOTH PAIRING
To pair the soundbar with a Bluetooth device:

1. Set your Bluetooth device into Bluetooth pairing mode (discoverable)
2. Press and hold the Bluetooth ( ) button on the remote control until the LED display on the soundbar shows “BT” blinking.
3. You can now search for the soundbar (SHOCKWAFE) using your Bluetooth device. For more information, refer to the user documentation of your device.
4. Play audio from your Bluetooth device. Volume can be controlled on your source device or soundbar remote control.

Note: If the soundbar detects a Bluetooth device that was previously connected, the soundbar will automatically connect to the Bluetooth device after Step 2
To disconnect the soundbar with a paired Bluetooth device:

1. Press and hold down the Bluetooth ( ) button on the remote control until the LED display on the soundbar shows “BT” blinking.
2. The soundbar is ready to pair with a new device.

RE-LINKING THE SUBWOOFERS WITH THE SOUNDBAR

1. Ensure the soundbar and two subwoofers are powered OFF

2. Power ON the LEFT subwoofer

3. Power ON the RIGHT subwoofer

4. Press and hold PAIRING button at the back of LEFT subwoofer until the BLUE LED light start blinking rapidly

5. Press and hold PAIRING button at the back of RIGHT subwoofer until the BLUE LED light start blinking rapidly

6. Power ON the soundbar

7. Pair the soundbar to the subwoofer in 2 ways:
   a. On the remote control
   i. Press the USB button on remote control to USB mode
   ii. Press the menu button and toggle to SUB PAIR option
   iii. Press ENTER and the “PAIR-” will be shown on LED display
   b. On the soundbar i. Press the -E button on the soundbar to toggle USB mode
   ii. Press and hold the DEMO button until “PAIR-” is shown on LED display.

8. The soundbar is in subwoofer pairing mode (LED display: “PAIR-“)

9. Once the linking process is completed, the soundbar’s LED display will show “DONE” and the Blue LED at the back of both subwoofers will stay lit constantly

Note: Once soundbar is powered off, the blue LED lights on the subwoofers will continue blinking for 10 minutes before going into standby mode.

WALL-MOUNTING YOUR SOUNDBSR SYSTEM SOUNBAR

1. Insert the 2 mounting screws into the wall-mount screw holes, and then tighten them.
2. Place the included wall-mounting template against the wall under ‘17 your TV. Mark the 4 bracket holes using a pencil.
3. Be sure your screws are attached to wood studs, drywall anchors w (for drywall), or concrete anchors (for brick/concrete walls).
   Choose the screw type and length appropriate to your home’s construction. If in doubt, consult a professional installer.

If you are unfamiliar with power tools or the layout of electrical wiring in the walls of your home, consult a professional installer.

WALL-MOUNTING YOUR SOUNDBAR SYSTEM (CONT.) SURROUND SPEAKERS

To wall-mount the surround speakers:

1. Attach the mounting screws to the back of the surround speaker
2. Align and mount the surround speaker with the wall mount bracket.

! Be sure your screws are attached to wood studs or drywall anchors (for drywall) or concrete anchors (for brick/concrete walls). Wall mounting tools are not included.
If you are unfamiliar with power tools or the layout of electrical wiring in the walls of your home, consult a professional installer.

FIRMWARE UPGRADE

Firmware upgrades that provide additional features and performance improvements are released occasionally. For more information, visit nakamichi-usa.com/72-sse-firmware
Do not perform this procedure unless firmware upgrade is necessary. Be sure to read the information supplied with the firmware before upgrading the firmware.

CHECKING THE FIRMWARE VERSION:
On the remote control toggle the INFO button until the LED display “FWXX”. The firmware version will be displayed.

SOUNDBAR FIRMWARE UPGRADE

1. Insert the USB stick with the unzipped firmware file (.BIN format) into the soundbar’s USB port
2. Press the USB button on the remote control to USB mode
3. Press MENU button to navigate firmware upgrade function (FWUPG on LED display)
4. Press and hold the ENTER button until “UPG—” is displayed on front LED display
5. Firmware upgrading process will be displayed on the LED screen
6. Once the firmware is completed, the soundbar will restart automatically

Firmware upgrade process may take up to 5 to 10 minutes. Update progress is displayed on the front panel display when the firmware is upgrading. During each upgrading stage, there will be a numeric percentage to show its progress.Once the firmware is completed, the soundbar will restart automatically to default factory settings.
! If the soundbar detected the same firmware version installed, “FW UP TO DATE” will be displayed on the soundbar LED display.

HELP & TROUBLESHOOTING

1. HDMI ARC/CEC – No Sound or Video
   Performing a Soundbar Soft Reset can restore the soundbar settings back to factory default and refresh HDMI settings. If your TV’s connected to another sound system via HDMI previously, perform a Soundbar & TV Hard Reset + HDMI Connection Refresh to establish a new HDMI handshake.

Soundbar Soft Reset:

1. Switch to HDMI ARC input
2. Press SETUP button multiple times to locate RESET function
3. Press ENTER button to select the function
4. Press ENTER button again to confirm RESET function
5. The soundbar will restart automatically to complete the reset sequence.
   (“HELLO” appears on soundbar LED and it will be back to ARC mode by default)

Soundbar & TV Hard Reset + HDMI Connection Refresh:

1. While all source devices are on, disconnect all HDMI cables connected to TV and soundbar as well as TV to soundbar
2. Power OFF TV, soundbar and all source devices
3. Unplug all devices from the AC outlets
4. Wait for 5 minutes before plugging the TV, soundbar and source devices back to the AC outlets
5. Power ON the soundbar, TV and all source devices
6. While they are on, connect the TV and soundbar via HDMI ARC. Once the connection is established, connect the source devices one at a time. Use Perfect Device Matching Tool on page 22 to create a customized setup guide based on your source devices

For web support, visit https://bit.Iv/nakamichi-faq or scan QR code

https://bit.ly/nakamichi-faq

2. Subwoofer or Surround Speakers Cut Out / Crackling / Popping:
Enable dedicated frequency communication between the soundbar and the subwoofers & rear speakers.
(*Available on FW34 firmware only)

1. Switch to any HDMI ARC input
2. Press SETUP button on the remote a few times until soundbar LED displays “D FRQ”
3. Use the LEFT or RIGHT arrow to select “DF ON”
4. Press ENTER button on the remote

If you are still having issues with your subwoofers, visit: bit.ly/72 -subwoofers-audio-distortion. For other subwoofer related issues, visit: bit.ly/72-dual-subwoofers- faq

• To check for firmware version, press INFO button on the remote control multiple times until you see FWXX on the soundbar front LED panel.
  3. The Soundbar or the Subwoofer Does Not Power On
  Please contact support@nakamichi-usa.com so we can work on a replacement (within 30 days of purchase). The system comes with a 1 year parts and labor warranty.
  4. No Sound from Surround Speakers
  Press the “DIRECT” or “STEREO” buttons on the remote to enable Dolby Surround, Dolby Upmix or All Channel Stereo to get sound from all speakers
  5. Low Volume from Surround Speakers
  Press the “STEREO” button on the remote to enable All Chanel Stereo for maximum surround speakers output. Best for YouTubeTm and music.

SPECIFICATIONS

SOUNDBAR
6 x 2.5″ Full Range Driver
2 x 1″ High Frequency Tweeter
SURROUND BACK LEFT & RIGHT
1 x 3″ Full Range Driver (Each side)
1 x 1″ High Frequency Tweeter (Each side)
WIRELESS LEFT & RIGHT SUBWOOFERS
1 x 8″ Down Firing Driver (Each side)
CONNECTIVITY HDMI
(Dolby Vision & 4K HDR Pass-Thru)
HDMI Out (ARC to TV) x 1
[HDCP 2.2] HDMI Input x 3 [HDCP 2.2] DIGITAL AUDIO OPTICAL
Input x 1 COAXIAL Input x 1
Analog AUX Audio Input x 1
BLUETOOTH 4.1, with aptX USB x 1
PERFORMANCE
Channels: 7.2
Sound Pressure Level SPL: 106 dB
Total Power: 800W
Power Output: 330W (Soundbar) 100W (Surround Back Left & Right) 370W (Subwoofer)
Frequency Response: 35Hz — 22kHz
AUDIO PROCESSING
Dolby Atmos, Dolby TrueHD, Dolby Atmos MAT, Dolby
Digital Plus, Dolby Digital, DTS:X, DTS-HD Master Audio,
DTS-HD High Resolution Audio, DTS Digital Surround
REMOTE CONTROL
52-Key Backlit LED
7 EQ Modes — Movie, Music, Sports, News, Game, Clear Voice, Night
DIMENSIONS, WEIGHT & POWER RATING
Soundbar: 45.5 x 3.5 x 3.0 Inches, 7.27 lbs.
Subwoofer: 9.5 x 12 x 20.5 Inches, 19.0 lbs.
(Each) Satellite Speaker: 5.0 x 5.4 x 8 Inches, 2.8 lbs.
(Each) Power Input:
Soundbar: 100 – 240V, 50/60 Hz
Subwoofer: 110 – 240V, 50/60 Hz

ONE YEAR LIMITED WARRANTY

LIMITED WARRANTY (U.S. Only)
Nakamichi LLC (“Nakamichi”) warrants this product against defects in material or workmanship for the time periods and set forth below. Pursuant to this Limited Warranty, Nakamichi will, at its option, (i) repair the product using new or refurbished parts or (ii) replace the product with a new or refurbished product. For purposes of this Limited Warranty, “refurbished” means a product or part that has been returned to its original specifications. In the event of a defect, these are your exclusive remedies.
Labor: For a period of one (1) year from the original date of purchase of the product (“Labor Warranty”), Nakamichi will, at its option, repair or replace with new or refurbished product, product determined to be defective. If Nakamichi elects to replace the product after this Labor Warranty has expired but while the Parts Warranty below is still in effect, it will do so for the applicable labor charge.
Parts: For a period of one (1) year from the original date of purchase of product (“Parts Warranty”), Nakamichi will supply new or refurbished replacement parts in exchange for parts determined to be defective.
This Limited Warranty covers only the hardware components packaged with the Product. It does not cover technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the Product; any such software is provided “AS IS” unless expressly provided for in any enclosed software Limited Warranty. Please refer to the End User License Agreements included with the Product for your rights and obligations with respect to the software.
Instructions: To obtain warranty service, you must deliver the product, freight prepaid, in either its original packaging or packaging affording an equal degree of protection to the Nakamichi authorized service facility specified. It is your responsibility to backup any data, software or other materials you may have stored or preserved on your unit. It is likely that such data, software, or other materials will be lost or reformatted during service and Nakamichi will not be responsible for any such damage or loss. A dated purchase receipt is required.
Repair / Replacement Warranty: This Limited Warranty shall apply to any repair, replacement part or replacement product for the remainder of the original Limited Warranty period or for ninety (90) days, whichever is longer. Any parts or product replaced under this Limited Warranty will become the property of Nakamichi.
This Limited Warranty only covers product issues caused by defects in material or workmanship during ordinary consumer use; it does not cover product issues caused by any other reason, including but not limited to product issues due to commercial use, acts of God, misuse, limitations of technology, or modification of or to any part of the Nakamichi product. This Limited Warranty does not cover Nakamichi products sold AS IS or WITH ALL FAULTS or consumables (such as fuses or batteries). This Limited Warranty is invalid if the factory- applied serial number has been altered or removed from the product.
This Limited Warranty is valid only in the United States. This Limited Warranty is valid only for Nakamichi products purchased from the following authorized retailers with a valid receipt stating date, product description and purchase price:

1. Amazon.com (under seller “Nakamichi LLC”)
2. Best Buy
3. Ebay (under seller “nakamichi-usa”)
4. B&H Photo Video

LIMITATION ON DAMAGES: NAKAMICHI SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT.
DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This Limited Warranty gives you specific legal rights any you may have other rights which vary from state to state.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This Limited Warranty gives you specific legal rights any you may have other rights which vary from state to state.

CUSTOMER SUPPORT

Thank you for your purchase of this Product. If you have any questions or comments, please visit our website at www.nakamichi-usa.com/faq or email us at support@nakamichi- usa.com Phone Support: (415) 805 6913 (Weekdays 10am – 7pm PST; Saturday, Holidays 10am – 5pm PST)

GLOSSARY

This section explains the technical terms used in this user manual.
Spatial Surround Elevation (SSE) Processing Technology
Nakamichi’s proprietary processing technology: A set of processing algorithms that takes surround sound performance to a whole new level. For more info, visit nakamichi-usa.com/shockwafe-sse
Dolby Atmos object-based audio
Dolby Atmos is an object-based audio format with the capability to reproduce up to 128 simultaneous objects. Every sound in a scene can be represented as a separate audio object that can be positioned and moved throughout the 3D space. For more information, visit htlps://www.dolby.corn/usren/brandsidolby- atmos.html
Dolby Vision
Dolby Vision transforms your TV experience with dramatic imaging with incredible brightness, contrast, color, details and dimensionality. And with the advanced capabilities in Dolby Vision, you’ll see there’s more to the story that generic HDR cannot reveal.
Dolby TrueHD
Dolby TrueHD is a lossless multi-channel audio codec developed by Dolby Laboratories which is used in home-entertainment equipment such as Blu-ray disc players and AN receivers It competes with DTS-HD Master Audio, a lossless codec from DTS.
Dolby Digital Plus
Dolby Digital Plus, also known as Enhanced AC-3 is a digital audio compression scheme developed by Dolby Labs for transport and storage of multi-channel digital audio. This format is commonly found on many streaming services, including Nettlix, Amazon Prime, and more.
Dolby Digital
Dolby Digital is a compressed digital audio format developed by Dolby Laboratories, Inc. that supports 5.1-channel audio. This technology is used for audio on most DVD discs.
Dolby Surround
Dolby Surround expands on stereo to deliver sound from the sides, behind, and even above you, creating a natural, multidimensional sonic environment based on the science of how humans hear. Dolby audio in your home theater improves the power, clarity, and realism of sound by offering up to 7.1 discrete surround channels and up to 9.1 channels of sound with height dimension.
Dolby Upmix Dolby Upmix expands on stereo to deliver sound all around you by offering up to 7.X discrete surround channels and up to 9.X channels of sound. It Is designed to bring cinematic surround sound to your home.
DTS:X object-based audio DTS X uses a new technology called object-based audio that processes each sound contained in an audio source as an “object” and memorizes each object’s sound changes and positional changes in a sound field to control these changes during playback. For more information, visit
https://dts.com/dIsx
DTS-HD Master Audio
DTS-HD Master Audio is an advanced lossless audio format developed to offer a high-definition home theater experience by DTS, Inc. It is commonly found on Blu-ray discs and it can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio) simultaneously.
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio is a compressed digital audio format that supports 7.1 channel and up to 96 kHz/24-bit audio. It remains fully compatible with the existing DTS multichannel audio systems.
DTS Digital Surround
DTS Digital Surround is a compressed digital audio format developed by DTS that supports 5.1-chan-nel audio. This technology is used for audio on most DVD discs.
NEURAL:X
Neural:X is the latest down-mixing/up-mixing and spatial remapping technology from DTS. It is built in to DTS:X to provide upmix of Neural:X-encoded data. In DTS:X for soundbars, Neural:X can produce up to 11.x channels.
DTS:X Dialog Control
DTS:X Dialog Control allows you to boost the dialog, making the dialog more intelligible. People with impaired hearing may also benefit. Note that the content creator may disable the use of this feature in the mix, so that DTS:X Dialog Control may not always be available.
PCM (Pulse Code Modulation)
PCM is a signal format under which an analog audio signal is digitized, recorded, and transmitted. This is the basis of digital audio. Linear PCM is a lossless audio format sampled in a linear format, without any audio encoding. It provides the best audio compatibility among different devices.
Lip Sync
Video output sometimes lags behind audio output due to the complexity of signal processing caused by an increase in video signal capacity and internet streaming delay. Lip Sync is a technique to compensate the timing lag between audio and video output.
Dynamic Range Control (DRC)
DRC is an audio signal processing operation that reduces the volume of loud sounds or amplifies quiet sounds thus reducing or compressing an audio signal’s dynamic range. This is also known as volume normalization.
Power Saving (ECO Mode)
Designed to prevent electrical wastage and promote eco-friendliness. ECO Mode automatically puts the system to standby mode when there is no signal detected for 20 minutes.
Subwoofer Crossover Frequency
The subwoofer crossover frequency is the frequency at which your speakers start to roll off and your subwoofer kicks in with low frequency effects and bass notes.

HDMI
HDMI (High-Definition Multimedia Interface) is the world-wide standard interface for digital audio/video signal transmission. This interface transmits both digital audio and digital video signals using a single cable without any loss. HDMI complies with HDCP (High-bandwidth Digital Content Protection) and provides a secure audio/video interface. For further informa- tion on HDMI, visit the HDMI website at “http://wvm.hdmi.orgt.
HDMI-CEC CONTROL
HDMI-CEC Control allows you to operate external devices via HDMI. If you connect a TV that supports HDMI CEC control to the soundbar with an HDMI cable, you can control the soundbar (such as power and volume) with TV remote control operations. Operation available from the N’s remote control:

• Standby synchronization.
• Volume control including mute.

HDCP
HDCP (High-bandwidth Digital Content Protection) is a digital copy protection form that prevents copying of digital contents as it travels across connections (such as HDMI).
What is aptrm™?
Qualcomm® aptXTm audio technology enhances the wireless sound quality of many of the world’s finest smartphones, speakers, headphones and tablets. Previously, these devices often had a reputation for providing average quality sound via Bluetooth, but with aptX, Bluetooth-enabled products can overcome that barrier and consistently deliver higher quality audio wirelessly.

The soundbar is compatible with the following audio formats:

DVD, etc.
Bitstream (SD Audio)| Dolby Digital, DTS| DVD-Video, etc.
Bitstream (HD Audio)| Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS Digital Surround, DTS-HD High Resolution Audio, DTS-HD Master Audio, DTS:X| Online streaming media, Blu-ray disc, HD DVD

• Refer to documentation supplied with the playback device, and set the device appropriately.
• To decode audio bitstream signals on this unit, set the input source device appropriately so that the device outputs the bitstream audio signals directly. Refer to documentation supplied with the device for details.

HDMI (ARC)

DIGITAL AUDIO SIGNAL (OPTICAU/COAXIAL)

DVD-Audio, etc.
Bitstream (5.1ch)| Dolby Digital, DTS Digital| DVD-Video, etc.

The soundbar is compatible with the following video resolution:

LEGAL & COMPLIANCE

FCC Class B Radio Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference.

RF Exposure Information
This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Disposal and Recycling
You must dispose of this product properly, according to local laws and regulations. Because this product contains electronic components and a battery, it must be disposed of separately from household waste. Contact local authorities to learn about disposal and recycling options.

COMPATIBLE WITH

Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos, Dolby Surround, Dolby Vision Compatible and the double-D symbol are trademarks of Dolby Laboratories.

For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, DTS in combination with the Symbol, DTS:X, and the DTS:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries.
© DTS, Inc. All Rights Reserved.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Nakamichi LLC is under license. Other trademarks and trade names are those of their respective owners.

Qualcomm aptX is a product of Qualcomm Technologies International, Ltd. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries, used with permission. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries, used with permission.

STOP PLEASE DO NOT RETURN THHIS UNIT
ONE-STOP SUPPORT SOLUTION
www.nakamichi-usa.com/faq
CUSTOMER CARE
support@nakamichi-usa.com
(415) 805 6913
(Weekdays 10am – 6:45pm PST; Saturday, Holidays 10am – 4:45pm PST)
SPEAK TO OUR SHOCKWAFE NINJAS IN USA TIDAY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>