havit HV1426NW-SS316 Mini Tivah Garden Spike Light Instruction Manual

June 4, 2024
havit

Luta Inground Light
Instruction Manual

havit HV1426NW-SS316 Mini Tivah Garden Spike Light

Product Specifications

Model No. HV1426NW-SS316 I HVI 426NW-BLK
Name Mini Tivah
Material 316 Stainless Steel Aluminium
Colour Stainless Steel Black
IP Rating IP65
Input Voltage 12v DC
Lamp Base MM 1
Lamp Wattage lx 3w
Colour Temp 3000k or 4000k
Lumens 2701m or 300Im
CRI > 80
Wiring Parallel
Dimmable No
Warranty 3 Years Replacement*

Important Safety Issues:

  • This product must be installed by a qualified electrician according to AS/NZS 30:0.
  • Ensure all electrical mains are disconnected before any installation.
  • Do not exceed maximum wattage restrictions for globes: 12V MR11 = 20w, Modification of this product wID void any warranty.
  • Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
  • All electrical connections must be watertight. If a watertight connection is not done, the Warranty will be voided
  • When installing low voltage fittings, the Voltage to fitting must be within +or- 5% of the voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided. Aluminum and 30455 fittings must not be installed within 51 cm of any saltwater environments.
  • All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting (Warranty does not cover Tea Staining).
  • All o-rings and seals must be in place correctly to maintain the warranty.
  • These instructions may be updated at any time due to product improvements, Please visit the website for the most current installation instructions.

Steps for Installation:

  1. Make sure that the electrical circuit is free of voltage (master switch off)
  2. Place fitting in the desired location
  3. Connect the cable –
  4. Use an appropriate 12v DC LED Driver – DO NOT CONNECT LIG-IT FITTING DIRECT TO 240V
  5. Strip back cable on both fittings and cable run and twist the positive cable from fitting to positive on the cable run, then connect neutral from fitting to neutral on the cable run.
  6. Solder all joins using solder with either a heat gun or butane gas torch.
  7. Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. (failure to do this step will void the warranty)
  8. Heat the heat shrink or crimp the gel cap making sure all connections are covered.
  9. Fitting is supplied with both 3000k and 4000k globes, Select which color temperature you want to use, remove covers from fitting by twisting anti-clockwise, and set them aside. Insert globes into lamp holder by aligning pins with holes and push down gently.
  10. Reinsert the globe by aligning the pins of the globe with the holes of the lamp holder and pushing down gently.
  11. Reinsert glass and reattach the cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
  12. Adjust fitting to the desired position making sure to stop rotating when fitting cannot rotate anymore, If forced fitting will continue to rotate and cause internal cables to become entangled causing fitting to short. If this is done, the warranty will be voided.
  13. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Changing Globes:

  1. Remove the cover by twisting anti-clockwise, remove the glass and set aside
  2. Remove the globe by grabbing the outside of the globe and pulling.
  3. Re-insert the appropriate globe by inserting the 2 pins into the lamp holder and pushing down gently. (Make sure not to exceed max wattage, see product label for correct info.
  4. Reinsert glass and reattach cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.

Must be installed by a licensed electrician
Contact Details:

143 Beauchamp
Road Matraville
NSW 2036 Australia| Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
---|---
**Warranty Terms & Conditions*| Additional Information**
---|---
|
https://havit.com.au/pages/warranty-terms-and-conditions| https://havit.com.au/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

havit User Manuals

Related Manuals