havit HV1825T Luta Inground Light Instruction Manual

Luta Inground Light
Instruction Manual

Product Specifications

Important Safety Issues:

• This product must be installed by a qualified electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Modification of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• When installing low voltage fittings, the Voltage to fitting must be within +or- 5% of the voltage required, if not within this allowance warranty will be voided.
• Aluminum and 304SS fittings must not be installed within 5km of any saltwater environments.
• All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining)
• All o-rings and seals must be in place correctly to maintain a warranty
• When installing inground light fittings, Adequate drainage must be allowed to prevent fittings from sitting in water for a long period of time, if no drainage is allowed, the Warranty will be voided. (See sample adequate drainage diagram for correct installation method.)
• This form may be updated at any time due to product improvements, please check the online installation form for the most current version.

Steps for Installation:

1. Make sure that the electrical circuit is free of voltage (master switch off)
2. Make a hole where the fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
3. Insert the canister, and ensure that the top is level with the ground or floor. Failure to do so will void the warranty.
4. Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
5. Connect the cable – If more than one fitting is installed, wiring must be done in parallel.
6. Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
7. Solder all joins using solder and either a heat gun or butane gas torch.
8. Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
9. Heat the heat shrink or crimp the gel cap making sure all connections are covered.
10. The Colour temperature is set to 3000K factory. To change, unscrew 4x nuts on the back of the face, Remove globe and select desired color temperature by moving switch on side of the globe and reinserting the globe.
11. Adjust fitting to the desired angle by pushing gently on either side of the globe until you reach the desired angle.
12. Reattach the 4x nuts and tighten making sure the seals are still in place and screws are tight to avoid any water penetration.
13. Insert fitting into the canister. Apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
14. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Changing Globe:

1. To change, unscrew 4x nuts on the back of the fitting, Remove the globe by grabbing around the edge and pulling gently, and Re-insert the appropriate globe, making sure the new lamp does not exceed max wattage, see product label for information.
2. Reattach the 4x nuts and tighten making sure the seals are still in place and screws are tight to avoid any water penetration.

Steps for Changing Globe:

1. To change, unscrew 4x alien screws on face of fitting, Remove globe by grabbing around the edge and pulling gently, Re-insert the appropriate globe, making sure new lamp does not exceed max wattage, see product label for information.
2. Reinsert the 4x alien screws and tighten making sure the seals are still in place and screws are tight to avoid any water penetration.

Must be installed by a licensed electrician
Contact Details:

143 Beauchamp
Road Matraville
NSW 2036 Australia| Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
---|---
**Warranty Terms & Conditions*| Additional Information**
---|---
|
https://havit.com.au/pages/warranty-terms-and-conditions| https://havit.com.au/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>