BeSV JTR Finest Pedal Assisted Electric Bicycle User Guide
- June 9, 2024
- Besv
Table of Contents
BeSV JTR Finest Pedal Assisted Electric Bicycle
Your BESV e-bike can be pedaled like a normal bike, and it can assist you
while you pedal. Be sure to read this Quick Start Guide before you start an
amazing ride with your BESV e-bike.
For further information, refer to the full user manual or visit
www.besv.com.
Introduction
Pedelec (A Type of E-Bike)
A pedelec is an electrically assisted bike that provides assistance when and
only when you pedal. The torque sensor located on the pedal crank bearing
detects how hard you are pedaling and determines how much power the motor
should provide to give you a pleasant ride. The electric motor is turned off
as soon as you stop pedaling. In most countries, there are laws regarding
pedelec design and the use of pedelecs. For example, the maximum assisted
speed is 25 km/hr (15.5 mph) in European countries. When you are reaching the
maximum assisted speed, the motor starts to reduce its power output until it
ceases in order to meet the law requirement. However, with the pedal-assist
function off, you may be able to surpass the maximum assisted speed with your
physical strength and agility.
Intended Use
For your safety and for avoiding damages to your bike, please make sure your
pedelec is used according to its intended use. BESV JTR is designed to be a
trekking pedelec. Please ride your bike under suitable conditions. If you have
other needs, such as downhill riding, please select other suitable bikes for
your safety. This pedelec is designed to be ridden by only one person (the
rider) and does not permit carrying infant, children or animals. Pedelecs do
not intend to limit the stature, perception, and mental ability of its user;
however, a child under 14 years old is prohibited to ride the pedelec. (Please
check your local laws; the minimum age may be higher.) According to EN
regulation the maximum gross weight of the e-bike, including the weight of
rider, accessories and/or cargo, is under 120 kg (264 lb). Do not exceed the
allowable gross weight. It is also not designed to pull or tow another bike,
trailer, or any other items via a connection system.
Notes for Cleaning
Do not use high-pressure or steam cleaning equipment to clean the bike. The
steam or water jet coming from a high-pressure cleaning machine may cause
damages to the bearings, bolted parts, fires or other bike surfaces and may be
difficult to be seen with naked eye. Water may also seep into bearings or damage
the electrical parts of the e-bike system. Such damages may lead to
malfunction and therefore risk of accident. Please try to keep your bike dry,
and avoid using excess water t o clean it.
Use soft cloth, sponge or brush to clean your bike. Use moderate amount of
neutral detergent for cleaning. Make sure there is no detergent residue on
your bike after cleaning. Please do not use non-neutral detergents to clean
your bike.
BESV Smart App
To get the full experience we have designed for you, remember to download the
BESV Smart App!
Follow the on-screen instructions to create an account and register your JTR.
The BESV Smart App is designed to work seamlessly with your JTR. Find your bike, get notified of its status, analyze your ride data, and fine-tune settings for optimal performance. Try out these valuable features now!
Know Your JTR
- HMI (Human Machine Interface)
- Flat Handlebar
- Headlight
- Integrated Battery
- Disc Brake Rotors
- Alloy Front Fork
- Charger Port
- Seatpost Clamp
- Rear Carrier
- Rear Light
- Fender
- Hub Motor
- Rear Derailleur
- Brake Lever
- Shifter Indicator
- Shift Levers
Introducing HMI Functions
HMI Overview
How to Turn On/Off the Battery Power
Please make sure that the battery has enough capacity.
| To turn ON | Long press |
|---|---|
| To turn OFF | Long press and then release |
Pedal Assist Modes
When the power is turned on, press the power button to switch pedal assist
modes.
| 0 | Light OFF | No Assist |
|---|---|---|
| 1 | Blue Light | ECO Mode |
| 2 | Purple Light | Smart Mode |
| 3 | Red Light | Power Mode |
Battery Level Indicator
How to Turn On/Off the Headlight and Rear Light
How to Shift Gears
You may shift one to two gears at once, depending on the distance the lever moves.
How to Recharge the Battery
JTR has integrated battery. Please correctly connect the charger to the battery port to recharge.
Acceptable charger input voltage: 100V~240V
While charging, HMI and Charger’s LED Indicators blink to reflect battery
capacity changes.
Battery and Charger Precautions
- If the charger cable, plug or outlet is damaged, wet or dirty, there is a risk of electric shock, which could be fatal. Under such conditions, please do not touch the items with bare hands and seek help from professionals.
- Use only the battery charger delivered with the product. Using any other charger could damage both the battery and charger, may cause overheating of the battery or even explosion.
- Do not submerge the charger in water. There are risks of electric shock or damage to the charger.
- Only use an undamaged power cable and charger in dry state.
- Please protect your equipment from humidity, to avoid corrosion. Please store your JTR in dry environment.
- Do not expose the bike in a storage temperature lower than -20°C or higher than 55°C. Please note that the internal structure of battery may be overheated to damage due to high temperatures greater than 55°C, particularly exposed to direct sunlight.
- JTR battery’s allowable operating temperature range is between -10°C and 55°C. Higher than lower than this range could result in battery malfunction.
- Do not open the equipment to reduce the risk of electrical shock. For safety reasons, it is only allowed to be opened by qualified service personnel.
- Do not expose the battery to high voltage.
- There is a fire risk if the temperature of battery rises up to a dangerous level.
- The battery and charger should be placed on the fire-retardant surface and stay away from inflammable items when charging is in progress. Do not charge the battery while it is on a carpeted floor.
- Please do not store the battery near combustible items.
- Do not cover the charger during charging. There is a risk of overheating, fire or explosion.
- Remove any possible foreign object from the charging socket, such as dusts, ice or snow before plugging in.
- Deep discharging of battery may result in internal damage. Avoid deep discharging of battery while in use or storage.
- Do not use the charger in a humid space or in an ambient temperature lower than 0°C or higher than 40°C.
- Avoid letting the battery experience sudden temperature changes.
- The ideal storage temperature for transport is between 20°C and 25°C.
- Please read all the instructions and warnings labels thoroughly before using the charger and battery.
- Replace damaged power cable and charger immediately.
- If not in use, the battery should be charged fully at least every 3 months.
- Please keep the battery away from children. Please ensure that children should not handle battery or charger without adult’s supervision.
- If you detect that the battery becomes very hot, emits a strong odor, starts to deform or performs in an unexpected way while in use, being charged or in storage, please stop using the battery immediately.
- After charging, if not in use, remove the battery from the charger and unplug the charger.
- Once done charging, please disconnect AC plug from the outlet before unplugging the DC power cord from the battery.
- Please always disconnect equipment from power supply before maintenance or repair.
How to Adjust Saddle Height
- Use 5mm Hex Key and turn counterclockwise to loosen the clamp.
- Adjust the seatpost (saddle height).
- Turn the key clockwise (4-6 Nm) to frighten the clamp.
WARNING: Make sure saddle height adjustment does not exceed the minimum seatpost insertion depth requirement. (The mark should be fully inserted into the seat tube.)
Max. Allowable Weight
The maximum gross weight of the e-bike, including the weight of rider,
accessories and/or cargo, is under 120 kg (264 lb).
Max. cargo weight for rear carrier: 25 Kg
Please do not exceed the maximum allowable weight indicated above.
Maintenance and Repair
The frequency of maintenance or repair will vary depending on various conditions (riding, storage, etc.). We recommend that you visit our authorized professional distributor at least once every year for service and repair in order to keep your BESV JTR in excellent condition. The User Manual contains a more comprehensive maintenance and repair guide.
Pre-Riding Check
Please check the following before riding your e-bike:
- Check if all parts of the e-bike is undamaged and can function properly.
- Check all bolted and connecting parts of the bike are secured in place.
- Test ride to check if there is any abnormal noise from your e-bike.
- Check that the brake pads are not overly worn; and ensure brake system is working properly.
- Test to see if you can pedal smoothly.
- Check if the transmission system allows you to shift gears smoothly.
- Make sure saddle height adjustment does not exceed the minimum seatpost insertion depth requirement.
- Make sure fire pressure is within recommended range, and pressure is not dropping abnormally; as well as fire tread depths are sufficient.
- Check if the battery has enough capacity for your upcoming ride. Check if the electronic system and HMI are working properly.
If you find anything to be abnormal, please refrain from riding and contact our service center or authorized professional distributor for assistance.
WARRANTY CARD
SCAN QR CODE FOR THE USER MANUAL
Documents / Resources
| BeSV
JTR Finest Pedal Assisted Electric
Bicycle
[pdf] User Guide
JTR, Finest Pedal Assisted Electric Bicycle, JTR Finest Pedal Assisted
Electric Bicycle, Pedal Assisted Electric Bicycle, Electric Bicycle, Bicycle
---|---