Panasonic EH-KE46 Hair Styler Instruction Manual
- June 4, 2024
- Panasonic
Table of Contents
Operating Instructions
(Household) Hair Styler
Model No. EH‑KE46/EH‑KE16
Thank you for purchasing this Panasonic product.
Before operating this unit, please read these instructions completely and
save them for future use.
Safety precautions
To reduce the risk of injury, loss of life, electric shock, fire, malfunction,
and damage to equipment or property, always observe the following safety
precautions.
Explanation of symbols
The following symbols are used to classify and describe the level of hazard,
injury, and property damage caused when the denotation is disregarded and
improper use is performed.
WARNING Denotes a potential hazard that could result in serious injury
or death.
CAUTION Denotes a hazard that could result in minor injury.
The following symbols are used to classify and describe the type of
instructions to be observed.
This symbol is used to alert users to a specific operating procedure that must
not be performed.
This symbol is used to alert users to a specific operating procedure that must
be followed in order to operate the unit safely.
WARNING
▶ Regarding the plug and cord
Do not use the cord bundled.
– Doing so may cause fire or electric shock.
Do not damage or modify, or forcefully bend, pull, or twist the cord.
Also, do not place anything heavy on or pinch the cord.
– Doing so may cause electric shock or fire due to a short circuit.
Do not use it when the plug or cord is damaged or hot.
Never use the appliance if the plug fits loosely in a household outlet
– Doing so may cause burn, electric shock, or fire due to a short circuit.
Do not connect or disconnect the plug to a household outlet with a wet
hand.
– Doing so may cause electric shock or injury.
WARNING
Do not wrap the cord around the main body when storing.
**** – Doing so may cause the wire in the cord to break with the load, and
may cause electric shock or fire due to a short circuit.
Disconnect the plug by holding onto it instead of pulling on the cord.
– Failure to do so may cause the wire in the cord to break and may cause burn,
electric shock, or fire due to a short circuit.
Always turn OFF the power switch and disconnect the plug from the household
outlet after use.
– Failure to do so may cause fire or burn.
Always ensure the appliance is operated on an electric power source matched
to the rated voltage indicated on the appliance.
Fully insert the plug.
– Failure to do so may cause fire or electric shock.
► In case of an abnormality or malfunction
Immediately stop using and remove the plug if there is an abnormality or
malfunction.
– Failure to do so may cause fire, electric shock, or injury. <Abnormality or
malfunction cases> I
• Air has not emitted
• Unit stops sporadically
• Interior becomes red hot and smoke is emitted
– Immediately request inspection or repair at an authorized service center.
► Maintenance
When you see sparks around the air outlet while using the hot air setting,
stop use and remove the lint on the air outlet and air inlet.
– Failure to do so may cause burn or fire.
**Regularly clean the plug to prevent dust from accumulating.
– Failure to do so may cause fire due to insulation failure caused by
humidity. Disconnect the plug and wipe with a dry cloth.
► Regarding the main body
Do not block, or insert hair pins or other foreign objects into the air
inlet, or air outlet.
** – Doing so may cause fire, electric shock, or burn.
Do not leave the area with the power switch left on.
– Doing so may cause a fire.
Do not use in proximity of flammable materials (such as alcohol, benzine,
thinner, spray, hair care product, or nail polish remover).
– Doing so may cause an explosion or fire.
**** WARNING
Never modify, disassemble, or repair.
** – Doing so may cause ignition or injury due to abnormal operation.
Contact an authorized service center for repair.
Do not store the appliance in a bathroom or location with high humidity.
Also, do not place it in a location where water may spill (such as the top of
a vanity).
** – Doing so may cause electric shock or fire.
Do not use the appliance with a wet hand.
** – Doing so may cause electric shock or fire due to a short circuit.
Do not store within the reach of children or infants.
Do not let them use it.
** – Doing so may cause burn, electric shock, or injury.
Do not immerse the appliance in water.
Do not use this hair styler near water.
Do not use this hair styler near bathtubs, showers, basins, or other
vessels containing water.
– Doing so may cause electric shock or fire.
This symbol on the hair styler means “Do not use this hair styler near
water”.
When the hair styler is used in a bathroom, unplug it after use since the
proximity of water presents a hazard even when the hair styler is switched
off.
– Failure to do so may cause an accident or injury.
For additional protection, the installation of a residual current device
(RCD) having a rated residual operating current not exceeding 30 mA is
advisable in the electrical circuit supplying the bathroom. Ask your installer
for advice.
– Failure to do so may cause an accident or injury.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge unless they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the appliance.
– Failure to do so may cause an accident or injury.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent, or similarly qualified persons in order to avoid a hazard.
– Failure to do so may cause an accident or injury.
CAUTION
► To protect your hair
Do not curl too much hair around the attachment.
– Doing so may cause burns to the skin or hair.
CAUTION
Do not curl and uncurl hair diagonally as shown in the diagram. EH-KE46
– Doing so may cause hair to become tangled, resulting in damage or burns.
Do not use the air inlet damaged.
** – Doing so may cause the hair to become tangled in the air inlet,
resulting in damage to the hair.
During use, be careful to prevent hair from being suctioned into the air
inlet.
** – Failure to do so may cause the hair to become tangled in the air
inlet, resulting in damage to the hair.
► Note the following precautions
Do not store the cord in a twisted state.
** – Doing so may cause the wire in the cord to break with the load, and
may cause electric shock or fire due to a short circuit.
Do not drop or be subject to shock.
** – Doing so may cause electric shock or ignition.
Only use for drying or styling human hair. (Do not use on pets, or to dry
clothing, shoes, etc.)
– Failure to do so may cause fire or burn.
Do not
use it on children or infants.
** – Doing so may cause a burn.
Do not touch the shaded area, which will become very hot during and
immediately after use.
** – Doing so may cause a burn.
During use, do not spray hair spray, etc. directly on the main body
(including attachments).
** – Doing so may cause fire, electric shock, or burn.
► Note**
- This hair styler is equipped with an automatic overheating protective device. if the hair styler overheats, it will be turned off. Switch off the hair styler and unplug it from the power socket. Allow it to cool down for approximately 5 minutes before using it again. Check that no dust, hair, etc. is in the air inlets and outlets before switching it on again.
Parts identification
a
A Air outlet
B Attachment release button
C Power switch
2: Dry mode
1: Set mode
0: Ott
D Main body
E Air inlet (filter)
F Cord| G Plug (The shape of the plug differs depending on the
area.)
H Blow brush
I Roller brush EH-KE46
J Slim roller brush EH-KE46
K Nozzle EH-KE46
---|---
Fixing the attachment
Turn the power switch OFF when attaching and removing attachments.
Mounting the attachment
Align the attachment with the hair styler as shown. Ensure that the groove of
the attachment and the hook of the body are aligned with each other. Insert
the hair styler in the attachment until it clicks.
Removing the attachment
Press the attachment release button and pull out the attachment to remove it.
What is an ion?
(ion generation method: High‑voltage discharge)
Ions are the result of negatively charged oxygen molecules making contact with
moisture in the air. Its diameter is smaller than 1/1000 of steam, and it
cannot be seen with the naked eye.
How ion works
Generally, hair has properties that make it easy to become positively charged
with electricity. When ions come into contact with hair, static electricity
build-up is reduced, and the hair becomes silky and easier to style.
How to use the hair styler
- Wipe excess moisture in the hair with a towel.
Untangle hair with a brush or comb with your fingers.
Attach an attachment, and insert the plug into a household outlet.
If you have long or full hair, it may take some time to dry so we recommend drying the hair with a dryer.
-
Turn on the power switch.
• Select either the “2” or “1” mode with the power switch. -
Blow the hair.
-
Turn the power switch OFF, and remove the plug from the household outlet.
• After the hair styler has cooled sufficiently, store in a location with low humidity.
Notes
- Check the hair styler periodically to ensure continued use. (See page 13.)
- If you use the hair styler with a spray product, it may absorb constituents of the spray and suffer a drop in performance. Do not use it together with a spray product.
How to use the attachments
Blow brush
Hair is easier to blow dry when held by the ends and applied tension.
To dry your hair
For straight hair
Hold the brush with your hand and move the hair styler downwards from the
roots to the ends of your hair.
To curl the ends (hair styling)
Hold the brush with your hand while moving the hair styler slightly downward
and rotating it in the direction of the desired curl.
- For inner curls: Rotate the brush toward you.
- For outer curls: Rotate the brush away from you.
► To prevent the tangling of hair
- Curl the hair no more than 1.5 times around the brush to prevent tangling.
In case tangling does occur, use a hair styling product containing oil to untangle your hair.
Roller brush EH-KE46
The roller is thick, which helps prevent hair from tangling when you release
the hair from the brush.
►For large curls
Rotate the brush to curl the hair approximately 1.5 times around the brush.
►For increasing volume
Gently grab the hair at the roots, and rotate the brush to lift the hair up
while applying tension.
Slim roller brush EH-KE46
The roller is thin for easily curling bangs and short hair.
The bristles on the brush are short, which helps to prevent tangling when your
release hair.
►To lift and curl bangs
Gently grab the roots of the bangs with a brush, and curl the hair while
rotating the brush.
► To curl short hair
Gently grab the hair at the ends with the brush and curl the hair
approximately 1.5 times around the brush.
► To prevent the tangling of hair When curling
Take only a small amount of hair and roll it at a right angle (90˚) 1.5 times
around the brush to prevent tangling.
When releasing
Keep the roller as far away as possible from your head and unroll the roller
at the same angle as your hair.
Nozzle EH-KE46
Use for overall drying.
Maintenance of the hair styler
- Make sure to check the air inlet and air outlet at least once every month, performing maintenance as needed. Dust or other foreign debris may build up and block these areas causing a degradation in performance as well as the following issues.
- When the hair styler is blowing hot air, occasionally it may turn off or sparks may be seen. In such cases, dust may have accumulated at the air inlet and/or the air outlet. Also, the air inlet may be being blocked by your hair, hands, etc. (This phenomenon is the result of the hair styler’s thermal switch. It is a protective device. The sparks do not pose a danger in and/or themselves.) Slide the power switch to the “0” position and remove the dust if dust has accumulated, or if the air inlet was blocked by your hair or hand, cool down the hair styler for approximately 5 minutes before using it again.
- Make sure to turn OFF the power switch and disconnect the plug from the household outlet. (Except when performing maintenance on the air outlet)
Maintaining the main body
Clean the housing only with a soft cloth slightly dampened with tap water or
soapy tap water.
Notes
-
Do not use thinner, benzine, alcohol, or other chemicals.
– Doing so may cause malfunction, cracking/discoloration of parts, etc. -
Leaving the hair styler with hair products or makeup still adhered to the handle or body may degrade the plastic, causing discoloration or cracking, and malfunction.
Maintaining the attachments
Remove dust and hair using a commercially available brush, and clean with a
hair styling product.
Notes
- As a precaution, allow the hair styler to cool before removing attachments.
- After cleaning, allow the hair styler to dry sufficiently before use.
Maintaining the air inlet
Clean at least once a month.
-
Remove the filter until it reaches the cord.
• Rotate the filter rib ( a) to the position marked▷ on the main body to remove it. -
Remove dust or hair by using a brush or a vacuum cleaner.
-
Attach the filter securely.
• Align the filter on the main body to the position marked▷ on the main body and rotate until the filter rib is aligned to the position marked on□ the main body to secure.
Maintaining the air outlet
Clean at least once a month.
- Remove the attachment from the main body.
- Clean the air outlet using a brush as shown.
Notes
- As a precaution, do not cover the air inlet with your hand.
- After maintenance is finished, some dust may disperse the first time the hair styler is reused.
Use the hair styler after first checking that dust has stopped dispersing.
Troubleshooting
| Problem | Possible cause | Action |
|---|
When using the hair styler, it turns off or sparks are seen. (These sparks are
caused by the thermostat switch and the protective device, and this is not
dangerous.) The hot air is abnormally hot. The plug is abnormally hot. You may
notice a characteristic odor when using this hair styler. There is an abnormal
sound or vibration. Air sometimes outputs and sometimes does not output when
moving the main body. There is a burning smell. A portion of the plug or cord
is abnormally hot. The main body or an attachment is partially deformed. The
amount of air is low. Air is not emitted. The interior of the air outlet is
red. The main body is abnormally hot. (turn the power switch OFF and check the
hair styler)| Lint has accumulated on the air inlet or air outlet.
Hair or something is blocking the air inlet.
The connection to the household outlet is loose.
This is caused by the ozone it generates and
is not harmful to the human body. ****|
Remove accumulated lint.
(See page 12.)
Do not block the air inlet.
Use a household outlet that fits securely.
If even one of these problems occurs,
stop using the product and contact
the store where you purchased it.
If the problems still cannot be solved, contact the store where you purchased the unit or a service center authorized by Panasonic for repair.
Specifications
| Product name | Hair Styler |
|---|---|
| Product model | EH‑KE46/EH‑KE16 |
| Power source | 220 V |
| Power consumption | 550 W |
| Accessories | Blow brush Roller brush EH-KE46 , Slim roller brush **EH- |
KE46 , Nozzle EH-KE46**
*Only available in Kuwait and Qatar.
This product is intended for household use only.
Panasonic Corporation
© Panasonic Corporation 2014
Printed in Thailand
EH0000KE460X X0000-0
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>