ZHUHAI M200 Thermal Label Printer Instructions
- June 9, 2024
- ZHUHAI
Table of Contents
ZHUHAI M200 Thermal Label Printer
Instruction
Please read the instructional manual carefuly betore using the product Please visit our official website for more information: www.phomemo.com
-
QR code for Instruction Manual Please scan the QR code below toobtain the printer s instruction manual.
Multilingual Comprehensive -
Please scan the QR code to obtain the multilingual comprehensive version of the instruction manual and more tutorials.
Item Checklist
NOTE: The number of label rolls on the checklist is determined by the contents of the shipped package.
Specifications
Product Introduction- Parts and Features
Button functions
Parts Description
Main Menu – Settings
Paper Roll Installation
-
Slide down the Open-Cover Button toopen the paper compartment cover.
-
Take out the paper holder inside the compartment.
-
Remove the left disk and insert the label roll (with the printing side facing down). Insert the left disk and push it to the right.
-
After the label holder is complete, insert the holder into the paper compartment.
-
Pull out around 15 mm of paper and close the paper compartment cover.
-
Hold the Power Button for 3 seconds.
-
Press the Eject Button once to detect and reposition the label paper.
-
The label paper is repositioned once it comes out
NOTE: On your first use or after you have replaced the label paper, the printer Automatically ejects paper to reposition the label paper. This helps avoid printing errors (incomplete print, non-centered content, etc.).
Downloading the App
WARNING
- You need to connect the printer through the Print Master app.
- In compliance with Google’ s requirement, Android phones must enable GPS (Location Services) before using Bluetooth.
Method 1:
Use your phone to scan the QR code to install the App.
Method 2:
Search for “Print Master” in the app store on your phone to download the App.
Connecting the Printer
- Turn on GPS (Location Services) (Android phones only)
- Open Print Master
- Tap the” Connect now button to search for your device.
- Press “Start using”
In compliance with Google’ s requirement, Android phones must enable GPS (Location Services) before using Bluetooth. Before connecting to your device in Print Master, please make sure your printer
NOTE: is turned on and your phone’ s Bluetooth is on.
Identifying the Label Size
The App is required to set the label size or template before printing. Please follow theinstructions to download it.
- Method 1: Check your label package.
- Method 2: Measure with a ruler,
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harm- ful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter mined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Maintenance Card
CONTACT
- Hotline: +1 855 957 5321 (US only)
- Hours: Mon-Fri 9AM-5PM (EST)
- Email: [email protected]
- Webside: www.phomemo.com