Eurother 6100E Paperless Graphic Recorder User Guide
- June 9, 2024
- Eurother
Table of Contents
6100E Paperless Graphic Recorder
6100E
User Guide
6100E 100 mm paperless graphic recorder Versions 5.5 and later HA029722/2 May
2016
100 MM PAPERLESS GRAPHIC RECORDER
PAPERLESS GRAPHIC RECORDER
USER GUIDE
LIST OF SECTIONS
Section
Page
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 PROCESS VARIABLE DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4 SETTING UP THE RECORDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5 FILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 6 MODBUS TCP SLAVE COMMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 7 TRANSMITTER POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 ANNEX A: SPECIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 ANNEX B: REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 ANNEX C: WEB SERVER DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
EFFECTIVITY
This manual refers to recorders fitted with software version 5.5. To determine
the software version fitted to the recorder, the ‘About’ screen in the System
menu may be accessed as described in section 4.6.9.
HA029722 Issue 2 May 16
User Guide Page i
User Guide Page ii
100 MM PAPERLESS GRAPHIC RECORDER
PAPERLESS GRAPHICS RECORDER USER GUIDE LIST OF CONTENTS
Section
Page
Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
SYMBOLS USED ON THE RECORDER LABELLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.1 UNPACKING THE RECORDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2.1 MECHANICAL INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2.2 ELECTRICAL INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
2.2.1 Signal wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
CONNECTOR WIRING DETAILS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
2.2.2 Supply voltage wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
LINE SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
LOW VOLTAGE SUPPLY OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
2.3 ACCESS FLAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
2.3.1 Stylus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
2.3.2 Card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
LED INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
2.3.3 USB Front Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
3 PROCESS VARIABLE DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
TRUNCATION OF NUMERIC VALUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
CURRENT TRACE ALARM ICONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 STATUS BAR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1.1 Current access level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1.2 Page name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1.3 Alarm indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
INSTRUMENT ALARM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CHANNEL ALARM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CHANGE BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DISK ICON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FTP ICON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1.4 Summary menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
INSTRUMENT ALARM SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ACK ALL ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ALARM SUMMARY PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ALARM ACKNOWLEDGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
BATCH SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MESSAGE LOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
REMOVE MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2 NAVIGATION Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.1 Key functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
ROOT MENU KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
ALARM SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
MESSAGE LOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3 FIRST SWITCH-ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.3.1 Access to Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
TEXT STRING ENTRY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TEXT STRING ENTRY (Cont.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.4 DISPLAY MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TREND HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TIME CHANGE RECORDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.4.1 Vertical Trend display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.4.2 Horizontal Trend display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.4.3 Vertical bargraph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.4.4 Horizontal bargraph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.4.5 Numeric display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.5 OPERATOR NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4 SETTING UP THE RECORDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.1 ARCHIVE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.1.1 Local Archive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
BRING ARCHIVE UP TO DATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
ARCHIVE ALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.1.2 Remote archiving (FTP transfer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
HA029722 Issue 2 May 16
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
LIST OF CONTENTS (CONT.)
Section
Page
4.2 SAVE / RESTORE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.2.1 Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 SAVE AS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.2.2 Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.2.3 New . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.2.4 Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.3 CONFIG KEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.3.1 Instrument configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 INSTRUMENT NAME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 NORMAL/SAVER DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 SAVE AFTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 MODBUS ADDRESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 MODBUS SECURITY DISABLED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 COMMS CHANNEL TIMEOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 PRESET HOUR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 PRESET MINUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 DISABLE WARNING DIALOGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 SHOW OPERATOR NOTES LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.3.2 Group configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 TREND UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 DESCRIPTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 TREND SPEED/TREND INTERVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 GRID TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 RECORDING ENABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 RECORDING SPEED/RECORDING INTERVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 TREND HISTORY DURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 ARCHIVE TO MEDIA ENABLE/ARCHIVE VIA FTP ENABLE . . . . . . . . . . . . . . . . 48 ALARM MESSAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 ACK MESSAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 POINT TYPE/SELECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.3.3 Channel/Alarm configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 CHANNEL NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 VALUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 INPUT TYPE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 LIN TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 INPUT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 INPUT HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 SHUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 RANGE LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 RANGE HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 RANGE UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 SCALED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 OFFSET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 SCALE TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 FILTER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 BREAK RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 COLD JUNCTION COMPENSATION (CJC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 DESCRIPTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 SPANNED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 ZONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 PV FORMAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 MAXIMUM DECIMAL DIGITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 COLOUR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 ALARM NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 ENABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 SETPOINT SOURCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 HYSTERESIS EXAMPLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 RATE-OF CHANGE ALARM EXAMPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 JOB NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 CATEGORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 WHILE/ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 ALARM MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4.3.4 Archive configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 COMPRESSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
User Guide Page iii
User Guide Page iv
100 MM PAPERLESS GRAPHIC RECORDER
LIST OF CONTENTS (CONT.)
Section
Page
4.3.3 Channel/Alarm configuration (cont.)
FLASH SIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
SHORTEST TREND HISTORY / DURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
CSV CHECK BOXES, DATE/TIME FORMAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
SHOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
ARCHIVE TO MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
MEDIA FILE FORMAT/FTP FILE FORMAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
ON MEDIA FULL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
MEDIA SIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
REMOVABLE MEDIA CAPACITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
MEDIA FULL EVENT LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
ARCHIVE TO REMOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
REMOTE PATH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
PRIMARY REMOTE HOST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
PRIMARY LOGIN NAME/PASSWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
SECONDARY REMOTE HOST/LOGIN/PASSWORD . . . . . . . . . . . . . . . . . . . . . . 64
CSV FILES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
MEDIA FILE FORMAT (Cont.). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
4.3.5 Event configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
EVENT NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
SOURCE TYPES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
EVENT SOURCES (Cont.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
SOURCE 1 SENSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
OPERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
SOURCE 2 SENSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
DESCRIPTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
JOB NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
CATEGORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
WHILE/ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
EVENT EXAMPLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
4.3.6 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
MESSAGE ENTRY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
CONFIGURABLE PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
EXAMPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
4.3.7 Maths configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
GROUP MINIMUM FUNCTION DETAILS (Cont.) . . . . . . . . . . . . . . . . . . . . . . . . . 75
Rolling Average FUNCTION DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
MODBUS ADDRESSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
4.3.8 Totalisers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
4.3.9 Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
COUNTER MODBUS ADDRESSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
4.3.10 Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
SELF-START EXAMPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
4.3.11 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
4.4 SECURITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
4.5 NETWORK KEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
4.5.1 Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
INSTRUMENT NUMBER/MAC ADDRESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
IP ADDRESS LOOKUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
BOOTP TIMEOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
IP ADDRESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
SUBNET MASK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
DEFAULT GATEWAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
SNTP SERVER ENABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
SNTP CLIENT ENABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
SNTP SERVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
LIST OF CONTENTS (CONT.)
Section
Page
SNTP TIMEOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 EUROPRP SERVER ENABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
4.5.2 Name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 LOCAL HOST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 DOMAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 PRIMARY/SECONDARY DNS SERVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
4.6 SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
4.6.1 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
4.6.2 Locale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 LONG DATE FORMAT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
4.6.3 Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
4.6.4 Input adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . 98 ADJUST PROCEDURE. . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 99
4.6.5 Ethernet Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 100
4.6.6 Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 101 CONFIGURABLE
PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . 101 COPY RULES. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
4.6.7 Job search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 SEARCH RESULTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
4.6.8 About . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 103 INSTRUMENT VARIANT . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . 103 CONFIG REVISION . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 103 LAST UPDATED . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . 103 AT VERSION . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 CREATED
ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 103 SUPPORT FILE . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 104
4.7 JOBS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
4.7.1 No Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . 105
4.7.2 Drive relay category . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 105
4.7.3 Totaliser category . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 105
4.7.4 Message category. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 106
4.7.5 Maths category . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 106
4.7.6 Clock category. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . 107
4.7.7 Counter category . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 107
4.7.8 Timer category. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . 108
4.7.9 Recording category . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 108
4.7.10 Alarm category . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 109
4.7.11 Archive category . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 109
5 FILE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
5.1 FILER OPTION MENU KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 5.2 THE HIDE KEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 5.3 FILE STRUCTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
6 MODBUS TCP SLAVE COMMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
6.1 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . 113
6.2 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . 113
6.2.1 Function Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 113 DIAGNOSTIC CODES . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 113 EXCEPTION CODES . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 114
6.2.2 Data types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 DATA ENCODING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
6.2.3 Invalid multiple register writes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
6.2.4 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 TO SEND A LOGIN REQUEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 TO SEND A LOGIN REQUEST (Cont.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
6.2.5 Text messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 LONG MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
6.3 ADDRESS MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
6.4 ADDRESS ALLOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
HA029722 Issue 2 May 16
User Guide Page v
User Guide Page vi
100 MM PAPERLESS GRAPHIC RECORDER
LIST OF CONTENTS (CONT.)
Section
Page
6.4.1 Instrument data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
6.4.2 Channel configuration data . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 124 CHANNEL 1 . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 124 CHANNEL 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 125 CHANNEL 3 . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 126 CHANNEL 4 . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
CHANNEL 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 128 CHANNEL 6 . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 129
6.4.3 Channel Run-Time data . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 130 CHANNEL 1 . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 130 CHANNEL 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 CHANNEL 3 . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 131 CHANNEL 4 . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
CHANNEL 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 132 CHANNEL 6 . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 132
6.4.4 Group data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 GROUP 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
6.4.5 Feature identification table (FIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
6.4.6 Indirection tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
6.4.7 IEEE 32-bit channel configuration data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 CHANNEL 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 CHANNEL 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 CHANNEL 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 CHANNEL 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 CHANNEL 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 CHANNEL 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
6.4.8 IEEE Area Channel run-time data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 CHANNEL 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 CHANNEL 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 CHANNEL 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 CHANNEL 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 CHANNEL 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 CHANNEL 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
6.4.9 Permanent ID table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
6.5 DATA TRANSMISSION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 FUNCTION CODES AND EXCEPTION CODES . . . . . . . . . . . . . . . . . . . . . . . . . . 142 TEXT STRINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
6.5.1 Function code 03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 REQUEST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 EXCEPTION RESPONSES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
6.5.2 Function code 04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
6.5.3 Function code 06 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 144 REQUEST. . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 144 RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 EXCEPTION
RESPONSES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 144
6.5.4 Function code 08 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 144
6.5.5 Function code 16 (Hex 10). . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 145 REQUEST. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 145 RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 EXCEPTION
RESPONSES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 145
7 TRANSMITTER POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
7.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
7.2 FUSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
7.2.1 Fuse Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
7.2.2 Access to the user connections/fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
7.2.3 User wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Annex A: SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
INSTALLATION CATEGORY AND POLLUTION DEGREE . . . . . . . . . . . . . . . . . . . . . . . . 149
Installation category II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Pollution degree 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
TECHNICAL SPECIFICATION (Recorder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
TECHNICAL SPECIFICATION (Universal input board) . . . . . . . . . . . . . . . . . . . . . . . . . . 153
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
LIST OF CONTENTS (CONT.)
Section
Page
WORST CASE ERROR CALCULATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Input error: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Range error: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Temperature error: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Linearisation error: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Cold junction compensation (CJC) error:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Maximum error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
TECHNICAL SPECIFICATION (Relay output board) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Annex B: REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
B1 DIAGNOSTICS DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
B1.1 Main diagnostic display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
B1.2 SPECIAL MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
B1.3 DISPLAY TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
B1.4 TOUCH CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
B1.4.1 Touch screen calibrate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
B1.4.2 Touch screen verify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
B1.4.3 Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
B1.5 SYSTEM SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
B1.6 DIAG SUMMARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
B1.6.1 MAC Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
B1.6.2 Software version number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
B1.6.3 Serial 1/Serial 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
B1.6.4 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
B1.6.5 Lockable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
B1.6.6 Option boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 RELAY OUTPUT BOARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
B1.6.7 Input boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
B1.6.8 Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
B1.7 QUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
B2 PREVENTIVE MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
B2.1 TOUCH SCREEN CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
B2.2 MAINTENANCE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 B2.2.1 Battery replacement procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
B3 OPTION ENABLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
B4 COLOUR SELECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
B5 TCP PORT NUMBERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
B6 ASCII CHARACTERS FOR SERIAL COMMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
B7 TIME ZONE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
B8 MENU STRUCTURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Annex C: WEB SERVER DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
C1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
C1.1 INTERNET LINKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
C1.2 ACCESS TABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
C1.2.1 Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 INSTRUMENT ALARMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 GLOBAL CHANNEL ALARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
C1.2.2 Trends. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 HORIZONTAL TREND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 VERTICAL TREND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 NUMERIC DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
C1.2.3 Message Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
C1.2.4 History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
C1.2.5 About . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
HA029722 Issue 2 May 16
User Guide Page vii
100 MM PAPERLESS GRAPHIC RECORDER This page is deliberately left blank.
User Guide Page viii
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
SAFETY NOTES
WARNING Any interruption of the protective conductor inside or outside the
apparatus, or disconnection of the protective earth terminal is likely to make
the apparatus dangerous under some fault conditions. Intentional interruption
is prohibited.
Note: in order to comply with the requirements of safety standard BS EN61010,
the recorder shall have one of the following as a disconnecting device, fitted
within easy reach of the operator, and labelled as the disconnecting device.
a. A switch or circuit breaker which complies with the requirements of
IEC947-1 and IEC947-3 b. A separable coupler which can be disconnected without
the use of a tool c. A separable plug, without a locking device, to mate with
a socket outlet in the building.
1. Before any other connection is made, the protective earth terminal shall
be connected to a protective conductor. The mains (supply voltage) wiring must
be terminated within the connector in such a way that, should it slip in the
cable clamp, the Earth wire would be the last wire to become disconnected.
2. In the case of portable equipment, the protective earth terminal must
remain connected (even if the recorder is isolated from the mains supply), if
any of the I/O circuits are connected to hazardous voltages*.
3. The mains supply fuse within the power supply is not replaceable. If it is
suspected that the fuse is faulty, the manufacturer’s local service centre
should be contacted for advice.
4. Whenever it is likely that protection has been impaired, the unit shall be
made inoperative, and secured against accidental operation. The manufacturer’s
nearest service centre should be contacted for advice.
5. Any adjustment, maintenance and repair of the opened apparatus under
voltage, should be avoided as far as possible and, if inevitable, shall be
carried out only by a skilled person who is aware of the hazard involved.
6. Where conductive pollution (e.g. condensation, carbon dust) is likely,
adequate air conditioning/filtering/ sealing etc. must be installed in the
recorder enclosure.
7. Signal and supply voltage wiring should be kept separate from one another.
Where this is impractical, shielded cables should be used for the signal
wiring.
8. If the equipment is used in a manner not specified by the manufacturer,
the protection provided by the equipment might be impaired.
- A full definition of
Hazardous’ voltages appears underHazardous live’ in BS EN61010. Briefly, under normal operating conditions, hazardous voltages are defined as being > 30V RMS (42.2V peak) or > 60V dc.
SYMBOLS USED ON THE RECORDER LABELLING
One or more of the symbols below may appear as a part of the recorder labelling.
!
Refer to the manual for instructions
Protective earth
This recorder for ac supply only
This recorder for dc supply only
This recorder for either ac or dc supply
Risk of electric shock
HA029722 Issue 2 May 16
User guide Page 1
100 MM PAPERLESS GRAPHIC RECORDER
USER GUIDE
1 INTRODUCTION
This document describes the installation, operation and configuration of a
paperless graphic recorder.
1.1 UNPACKING THE RECORDER
The recorder is despatched in a special pack, designed to give adequate
protection during transit. Should the outer box show signs of damage, it
should be opened immediately, and the recorder examined. If there is evidence
of damage, the instrument should not be operated and the local representative
contacted for instructions. After the recorder has been removed from its
packing, the packing should be examined to ensure that all accessories and
documentation have been removed. The packing should then be stored against
future transport requirements.
2 INSTALLATION
2.1 MECHANICAL INSTALLATION
Figure 2.1 shows mechanical installation details.
Note: It is recommended that the rear face of the panel be centre-punched at
suitable positions to locate the tips of the case clamps. Otherwise,
particularly on smooth surfaces, the clamps can `wander’ as they are
tightened, leading to inefficient clamping and possible damage to the recorder
mounting slots.
The unit is inserted through the panel aperture from the front of the panel.
With the weight of the recorder supported, a panel clamp is inserted into each
of the mounting slots (one each on the left- and right-hand sides). The
jacking screws are then tightened sufficiently to clamp the recorder into
position. EXCESS FORCE SHOULD NOT BE USED IN TIGHTENING THESE SCREWS.
User guide Page 2
HA029722 Issue 2 May 16
102 mm 106.9 mm
137 mm
2 INSTALLATION (Cont.)
144 mm
100 MM PAPERLESS GRAPHIC RECORDER
24.75 mm
Standard terminal cover: 246.5 mm Long terminal cover: 288 (closed); 415mm
(open)
211.5 mm
Safety Earth
144 mm
35 mm
Front view
Access Flap
x
Panel cutout 138mm x 138mm (+1 – 0)
or 5.44 x 5.44 inches
(+0.04 – 0.00)
Minimum recommended inter-unit spacing
Side clamps
Top/bottom clamps
x = 15 mm (0.6 inch) x = 10 mm (0.4 in)
y = 10 mm (0.4 in)
y = 15 mm (0.6 inch)
y
Side elevation (RHS)
Panel thickness = 3 to 25 mm. Optimum thickness depends on panel material
View on underside
137 mm
Vertical
Maximum installed angle a° = b° = 45 degrees max
a° b°
Panel clamping
HA029722 Issue 2 May 16
Figure 2.1 Mechanical installation
User guide Page 3
100 MM PAPERLESS GRAPHIC RECORDER
2.2 ELECTRICAL INSTALLATION
2.2.1 Signal wiring Figures 2.2.1a shows connector locations for the recorder;
figure 2.2.1b gives pinouts.
CONNECTOR WIRING DETAILS
Maximum wire size = 4.13mm2 (11 AWG) Minimum wire size = 0.081mm2 (28 AWG)
Design torque = 0.35Nm.
Option slot
Safety Earth (M4)
Ethernet RJ45
E
L
N
Mains (supply) connection
Input channels 1 to 6
Figure 2.2.1a Connector locations
User guide Page 4
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
2.2.1 SIGNAL WIRING(Cont.)
Input board pinouts
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
Channel 1 Channel 2 Channel 3 V+ V- I V+ V- I V+ V- I
Cold junction
Channel 4 (Option)
V+ V- I
Channel 5 (Option)
V+ V- I
Channel 6 (Option)
V+ V- I
V+ V- I
V+ V- I
V+ V- I
+-
-20 to + 20 V dc Thermocouples
dc millivolts
V+ V- I
Attenuator assembly
+-
-200 to + 200 V dc
Shunt assembly
+-
DC milliamps
V+ V- I
V+ V- I
RTD 3-wire resistance
thermometer
V+ V- I
RTD
2-wire resistance thermometer
Potentiometer Potentiometer
-30V < Vin < +0.8V = active +2V < Vin < 30V = not active +0.8 < Vin < 2V = not defined
V+ V- I
nc
com
no
Minimum contact = 60m sec
Digital input (contact closure) (Not channel 1)
Not active (2 to 30 V) Active (0.8 to -30 V)
Vin
User 0V
Digital inputs (voltage levels) (Not channel 1)
Relay output board pinouts
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
Relay 1
Relay 2
Relay 3
nc c no nc c no nc c no c
nc Internal wiring (Contacts shown in
power off/alarm state)
no
HA029722 Issue 2 May 16
Figure 2.2.1b Pinouts
User guide Page 5
100 MM PAPERLESS GRAPHIC RECORDER
2.2.2 Supply voltage wiring WARNING
DC supply voltages must never be applied to recorders fitted with isolated
transmitter power supplies.
Note: The minimum recommended wire size is 20AWG equivalent to 16/0.2
(0.5mm2).
LINE SUPPLY
The supply voltage to the recorder is terminated using an IEC socket which is
connected to the mating plug at the rear of the recorder. The recorder is
suitable for use with all ac voltages between 85 and 265 V RMS (47 to 63 Hz),
and requires 50 W max. power. For recorders without transmitter power
supplies, supply voltages between 110V dc and 370V dc are also suitable.
LOW VOLTAGE SUPPLY OPTION Not suitable for recorders fitted with the isolated transmitter power supply option.
The low voltage supply option is terminated at a three-pin connector (plug
mounted on recorder – socket on
supply cable) as shown in figure 2.2.2. The option allows the use of ac or dc
supplies with the following characteristics:
AC: DC: Power:
20 to 42V RMS (45 to 400 Hz) 20 to 54V (See warning above) 50 W max.
Earth
+V or ac
0V or ac
Figure 2.2.2 Low voltage supply pinout (view on fixed connector face)
User guide Page 6
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
2.3 ACCESS FLAP
The access flap is located immediately below the recorder screen. To open the
flap, insert one or more fingers under the flap handle, and pull it outwards
and down (figure 2.3). Located behind the flap are (from left to right) 1. a
stylus (press to eject) 2. a slot for a Compact Flash card 3. a USB port
(usbfront).
Stylus storage
a) Insert finger(s) and pull forward and down Figure 2.3 Access flap detail
Compact Flash card
b) behind flap details
USBfront
2.3.1 Stylus
A stylus suitable for use on the touch screen is located in a storage area to
the left of the Compact Flash Card slot.
2.3.2 Card slot
The slot for the Compact Flash card is located centrally behind the flap. If a
card is already fitted, it is removed by a double operation of the eject
button. See details in figure 2.3.2 below
CAUTION
Removal of the memory device whilst archiving is in progress causes
irreparable damage to the filing structure on the device, rendering it
unusable. For this reason, archiving should be suspended (section 4.1) (wait
for the green section of the disk icon (section 3.1.3) to go white’) before the device is removed. It is strongly recommended that theRemove Media’
facility described in section 3.1.4 (Summary menu) be used to ensure that it
is safe to remove the memory device.
HA029722 Issue 2 May 16
Eject button (Press twice)
Compact Flash card
Figure 2.3.2 Compact Flash card details
User guide Page 7
100 MM PAPERLESS GRAPHIC RECORDER
2.3.2 CARD SLOT (Cont.)
LED INDICATORS Three LED indicators are located above the card slot as shown in figure 2.3.2b, below.
Card activity LED (yellow)
Power/watchdog LED (green)
USBFront Power LED (yellow)
Ejector
Card slot
Figure 2.3.2b indicating LEDs
2.3.3 USB Front Port A type-A USB socket is located to the right of the
Compact Flash slot. This port can be used to connect a mouse, a keyboard, a
barcode scanner, a `memory stick’ or a floppy disk drive.
Note: It is the responsibility of the user to establish the electromagnetic
susceptibility of any USB peripheral connected to the recorder. Refer to the
USB port specification in Annex A for details.
User guide Page 8
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3 PROCESS VARIABLE DISPLAY
The operator interface consists of a touch-sensitive screen, showing either
process variable values in one of a number of formats, or, showing
configuration or operational details for use in setting up the recorder. This
section (3) describes the process variable displays. Section 4 describes the
Configuration displays.
Figure 3, below, depicts a typical trend display for a large-frame unit and
gives details of the various areas of the display page.
Notes:
Dialogue boxes, message boxes etc. cause Process Variable displays to freeze’ for as long as the box is on display. Root and Option menus (amongst others) time-out (i.e. are removed from the display) after approximately one minute. Messages, however, are displayed until the operator takes action to remove them. It should be noted, especially, that several message boxes may be active at one time, but only the oldest one is visible, until it is removed to reveal thenext oldest’ message, and so on.
TRUNCATION OF NUMERIC VALUES
If the amount of space on the display page is insufficient to display the full
width of the process variable or scale value, then the displayed value is
rounded down and the number of decimal places reduced. If the width is still
too restricted, the value is displayed in scientific’ format, or if this is still too wide, the final visible character of the integer part of the value is replaced by a?’ (as depicted in figure 3.4.3b)
Current access level or user name
Page name
Change battery alarm Channel alarm System alarm
Status bar
Engineer
Group 1
Current channel details
Channel descriptor
0.0000
Alarm threshold
0.2000
0.4000
Disk icon (% free space)
FTP activity indicator
Time and date
14:39:26 21-Jan-08
99%
0.7612 V
14:39:26 21Jan08
0.6000
0.8000
1.0000
An animated bar appears over the date, when the recorder is busy.
Non-current traces (Pen icon)
Scale (Current) trace (Diamond icon)
Current1t4ra:c3e8a:4la6rm 21icoJnasn08
Off channel(s)
21Jan08 14:38:10 Alarm(s) off 3(1)
Alarm message (Channel 3 alarm 1)
Date/time stamps
14:38:06 21Jan08
14:37:26 21Jan08
Navigation keys
14:36:46 21Jan08
Figure 3 Trend display definitions (large frame unit)
HA029722 Issue 2 May 16
User guide Page 9
100 MM PAPERLESS GRAPHIC RECORDER
3 PROCESS VARIABLE DISPLAY (Cont.)
CURRENT TRACE ALARM ICONS In each of the different types of PV display, each
channel’s faceplate gives the status of the channel’s alarms. The status of
each alarm is shown by one of the icons depicted in table 3, either flashing
(if it is active and unacknowledged) or on continuously (if it is active and
acknowledged). (See section 3.1.4, below, for a description of how to
acknowledge alarms.) Absolute alarm threshold icons and deviation alarm bars
appear in any display which includes a scale. For deviation alarms the bar
stretches from (Reference – Deviation) to (Reference + Deviation).
Note: `Trigger’ alarms do not display threshold marks or bars, or faceplate
symbols.
Absolute High Absolute Low Deviation in Deviation out Rate-of-change Rising
Rate-of-change Falling
Faceplate symbols
Absolute Absolute Deviation Rate of
low
high In / Out change
Horizontal scales
dRd
No indication
Vertical scales
dd
R
No indication
For Deviation alarms, R = Reference; d = deviation
Scale symbols
Table 3 Alarm icons
3.1 STATUS BAR
This appears across the top of the display, and contains the items described
below.
3.1.1 Current access level There are four access levels available (Logged out,
Operator, Engineer and Service), and the current level is displayed in this
key at the top left hand corner of the display. Touching this key calls the
login page as described in section 3.3.1 (Access to configuration) below.
3.1.2 Page name Initially this shows the current group’s descriptor. The name
changes according to context for example Operator’ orConfig-Archive’
User guide Page 10
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.1.3 Alarm indication
This area of the display can contain a number of status icons: Instrument
alarm, Channel alarm, Battery change, Disk status, FTP in progress, and so on.
Pressing this area of the screen calls the Summary menu’ – (section 3.1.4) allowing the user to view active instrument alarms, to acknowledge all channel alarms, to display the Alarm Summary or Message Log page. Media removal strategy is also controlled from this pop-up. For channel alarm symbols refer toCurrent Trace Alarm Icons’, above.
INSTRUMENT ALARM
This indicator appears, flashing, if any of the following errors are active. The instrument alarm summary page, described in Section 3.1.4, allows the user to view such instrument alarms as are active.
Archive failed -(message)
Message explains archive failure.
Battery-backed RAM cleared
This message appears if the battery has failed, and the unit has been
switched off.
Clock failure
Internal clock was corrupt at power up, or the time has never been
set. Can be caused by battery failure, in which case the battery icon
will also be visible. The error is cleared by setting the time and date.
Server time forced to 00:00 1/1/1900.
Channel error
Indicates a hardware failure in the channel circuit or in the internal CJ
temperature measurement
Channel failure
Indicates a hardware failure in the input channel circuit (see note).
DHCP Server failure
For instruments with IP address lookup set to `Get from DHCP Server’, this alarm occurs if the recorder cannot obtain an IP address from the server. See section 4.5 for details.
FTP Archiving file lost
Archive failed. A file which has not been archived, has been detected.
FTP Archiving too slow
Remote archive is too infrequent. The recorder effectively switches to
`Automatic’ (section 4.3.4) to ensure that data is not lost.
FTP Primary Server Failure
This error is set if the recorder fails, after two attempts, to establish
communications with the primary server as defined in Archive Configuration (section 4.3.4). After the second attempt has failed, the Secondary server is tried.
FTP Secondary Server Failure
This error is set if the recorder fails, after two attempts, to establish
communications with the secondary server as defined in Archive Configuration (section 4.3.4). See also `FTP Primary Server Failure, above.
Insufficient non-volatile memory…
There is insufficient memory available for the configuration. Can be caused by use of Rolling Average maths functions.
Internal flash: application required repair Error found in the internal file system at power-up, and corrected.
Internal flash: history required repair Error found in the internal file system at power-up, and corrected.
Internal flash: screens required repair Error found in the internal file system at power-up, and corrected.
Internal flash: user required repair Error found in the internal file system at power-up, and corrected.
Internal flash: user is full
Appears if the User partition is full. To clear, either user screens must be simplified or files must be deleted from User, or both.
Maths Channel failure
Appears if, for example, the divisor of a divide function is zero.
Media Archiving file lost
Archive failed. A file which has not been archived, has been detected.
Media Archiving too slow
Archive is too infrequent. The recorder effectively switches to `Automatic’ (section 4.3.4) to ensure that data is not lost.
Note: Unlike other instrument alarms, Channel Failure is not self clearing. Once the cause of the failure is rectified, the recorder must be power cycled in order to clear the alarm.
HA029722 Issue 2 May 16
User guide Page 11
100 MM PAPERLESS GRAPHIC RECORDER
3.1.3 ALARM INDICATION (INSTRUMENT ALARMS) (Cont.)
Network boot failure Recording failure – (message) Removable media failure
Removable media full SNTP server failure Time synchronisation failure
USB over current USB power fault key USB unsupported
The recorder is unable to establish connection with the BootP or DHCP server.
This might be caused by, for example, cable failure, network hardware failure,
etc.
Message explains recording failure – due to file error, internal overflow etc.
This error is set if the archive storage device is corrupt, wrongly formatted
etc. Becomes active only when an Archive is attempted.
Archive storage device full. Becomes active only when an Archive is in
progress.
This error is set if:a) the year received from the server is < 2001 or > 2035
or b) the configured SNTP server cannot be accessed. Set if 5 or more Time change events’ are caused by the SNTP server within 24 hrs. ATime change
event’ occurs whenever the recorder time is found to be more than 2 seconds
different from the server time. The alarm does not appear until 24 hours have
elapsed since the first of the five or more Time Change events occurred. USB
power fault – too much current being drawn by a USB device (max 500 mA).
USB power fault – too much current being drawn by all USB devices (max 1100
mA)
Unsupported USB device inserted.
User guide Page 12
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.1.3 ALARM INDICATION (Cont.)
CHANNEL ALARM
This red bell’ indicator appears if any channel is in alarm. The symbol is illuminated continuously if all alarms are acknowledged or flashes if any active alarm is unacknowledged. Refer toALARM ACKNOWLEDGEMENT’ below, for
details of how to acknowledge alarms.
CHANGE BATTERY
This flashing indicator first appears when the battery voltage (checked every
15 minutes) indicates that the battery is approaching the end of its useful
life. The indicator continues to flash until the battery is replaced (B2.2 in
Annex B). The indicator does not appear if the battery is not fitted.
DISK ICON
This shows the free space available on whatever mass storage medium is fitted
(if any), and selected for Archive destination (note 1). The disk icon appears
soon after the device is inserted (but see note 2). During archiving, the
colour of the central area of the disk changes to green (see note 3). No other
disk activity (e.g. save/restore configuration) is indicated.
This area of the icon coloured green during any archive activity
(not necessarily to the device selected in Archive configuration).
99%
Figure 3.1.3 Archive activity indication
Notes
1. The icon appears only when a memory device is present, AND when that
memory device has been selected in the Archive to media’ selection in archive configuration (section 4.3.4). For example: if a memory stick is inserted in usbfront’, but Archive to Media is set to mediacard’, then the disk icon ap.pears only if a suitable card is present in themediacard’ slot.
2. When a disk is inserted into a USB floppy disk drive which is connected to
the recorder, the disk icon appears only after the disk has been accessed,
(either by reading from it or writing to it), or after the file system has
been opened by touching the `file’ key. (This note does not apply for disks
which have been inserted before the disk drive is plugged in.)
3. The central area goes green whenever local archiving is taking place – not
only when archiving is taking place to the memory device selected in Archive
configuration.
FTP ICON The FTP icon appears to the right of the disc icon position whenever transfer activity is taking place.
HA029722 Issue 2 May 16
User guide Page 13
100 MM PAPERLESS GRAPHIC RECORDER
3.1.4 Summary menu This pop-up display appears if the Alarm Indication area at
the top of the display is touched. Figure 3.1.4 shows the display.
Touch Alarm area (e.g. channel alarm symbol) Summary Instrument Alarm Summary
Ack all Alarms Alarm Summary Batch Summary Message Log Remove Media
Figure 3.1.4a Summary pop-up menu
INSTRUMENT ALARM SUMMARY
Instrument Alarm Summary
Maths Channel Failure DHCP Server failure
Ok
Figure 3.1.4b Typical Instrument alarm summary display This contains a list of
the currently active instrument alarms. For a list of possible alarms and
their definitions, see section 3.1.3, above.
ACK ALL ALARMS
Ack all Alarms Confirm acknowledge of alarms?
Yes No
Figure 3.1.4c Ack all Alarms display `Yes’ confirms all active, unconfirmed
alarms. This page can also be displayed by touching an alarm in the alarm
summary page, described below.
User guide Page 14
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.1.4 SUMMARY MENU (Cont.)
ALARM SUMMARY PAGE
As shown in figure 3.1.4d, below, the alarm summary page contains the
following information for the current group:
1. Alarm identifier. This appears as a point ID, followed by the relevant
alarm number in parentheses. For example, Alarm 1 on maths channel 6 would
appear as: D6 (1). Maths channels are prefixed by D’. Totalisers are prefixed byT’ and Counters are prefixed by `C’. Input channels are not prefixed.
2 Alarm threshold for absolute alarms only 3 The current process value for the
point 4 An alarm symbol (see Table 3). Alarm symbols flash until acknowledged.
Notes:
1. Alarms are always listed in Point/Alarm order with input channels first,
followed by derived channels, totalisers and counters, if these options are
fitted.
2 When the alarm source returns to its non-alarm state: Unlatched alarms are
removed from the list whether or not they have been acknowledged; latched
alarms remain displayed until acknowledged. See section 4.3.3 for a
description of alarm types and actions.
3. There are no time or history components associated with the Alarm Summary.
If Alarm messages have been enabled in the group’s configuration (section
4.3.2), then alarm initiation/acknowledgement times and dates can be found
from the trend and trend history displays, described in section 3.4 or in
Message log described later in this section.
4. If an alarm is active on a channel which is not included in any group,
then although the channel alarm symbol will flash, the alarm will not appear
in any of the alarm summary pages.
Instrument Alarm Summary
Maths Channel Failure
Ok
See section 3.2.1 See section 3.2.2
Touch Alarm area (e.g. channel alarm symbol)
Summary
Instrument Alarm Summary Ack all Alarms
Ack all Alarms Confirm acknowledge of alarms
Alarm summary
Yes No
Message Log
Remove Media
Alarm Summary: Group 1
1(1) Water temp 1a
60.0000 C
68.5277
2 (1) Water temp 1b
30.0000 C
23.4531
2 (2) Water temp 1b 3 (1) 0il presA(Aslabursmorleusetetpaolainrtms only)
10.0000 C caTlol u’Acchkanloawrmledtog2e3′ .4531 250.000 PSI dialogue bo2x.60.3425
4(1) Transfer Ack Alarm
15.3678
Channel no. Channel (alarm no.) descriptor
Confirm acknowledge of alarm?
Yes No
Current Process Alarm type
Value
symbol
HA029722 Issue 2 May 16
Figure 3.1.4d Alarm Summary display
User guide Page 15
100 MM PAPERLESS GRAPHIC RECORDER
3.1.4 SUMMARY MENU (Cont.)
ALARM ACKNOWLEDGEMENT Alarms can be acknowledged individually, on a group
basis, or globally (all alarms).
INDIVIDUAL ALARMS
Individual alarms are acknowledged from the alarm summary page by touching the
relevant item (highlights yellow), then touching Yes’ in the resulting pop-up confirmation box. Figure 3.1.3a, above, attempts to show this process. GROUP ALARMS Alarms can be acknowledged on a group basis by calling the alarm summary page, then pressing the Options key (section 3.2), theAck Group Alarms’ key and
finally, `Yes’ in the resulting pop-up confirmation box. Figure 3.1.4e below,
attempts to show this process.
Alarm Summary: Group 1
1 (1) 2 (1) 2 (2) 3 (1) 4 (1)
Water temp 1a
60.0000
Water temp 1b
30.0000
Water temp 1b
10.0000
0il pressure
250.000
Transfer
Option Menu
Note
68.5277 C 23.4531 C 23.4531 C 260.3425 PSI 15.3678
Ack Group Alarms
Ack Group Alarms Confirm acknowledge of alarms?
Yes No
Figure 3.1.4e Group Alarm acknowledgement
ALL ALARMS
To acknowledge all active alarms, touch (e.g.) the channel alarm icon at the
top of the screen. From the resulting Summary’ menu, selectAck all Alarms’,
then finally, touch `Yes’ in the resulting pop-up confirmation box.
Note: The options menu is context sensitive, and may, therefore, not appear as
illustrated above.
BATCH SUMMARY Not applicable this model of recorder
User guide Page 16
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.1.4 SUMMARY MENU (Cont.)
MESSAGE LOG
Note: Message log can also be selected using the Root menu/Goto View/Message
log key.
If there are more messages than can be displayed in the height of the screen,
a scroll bar appears to allow hidden’ messages to be displayed. Messages are retrieved from the history files in batches of 100 messages. If there are more than 100 messages,Earlier messages..’ appears after the
hundredth message. Touching Earlier messages..’ calls the option menu, and touchingEarlier messages..’ in this menu, calls the next batch of 100, and
so on. If applicable, operating Later messages..’ /Later messages..’ calls
the previously displayed 100 messages.
As can be seen from figure 3.1.4f the list of messages can be filtered’ both by type and by time. For example, setting the message type toAlarm’ and the
period filter to `Last Day’ excludes all messages except alarm messages which
have occurred within the previous 24 hours. (For clarity, the figure shows
both filters open. In fact, only one can be open at a time)
Touch Alarm area (e.g. channel alarm symbol)
Summary
Instrument Alarm Summary Ack all Alarms Alarm Summary Batch summary Message
Log Remove Media
Engineer
Group 1
15:24:36 28/01/08
All Messages
All History
MesSsyasgteemLog: Group 1
Last Hour
28/08A/l0a1rm1s5:24:09 Alarm(s) on 1(1)
28/01/08 15:23:21 Alarm(s) on 2(1) Power Up
28/01/08 15:22:56 Alarm(s) off 2(1)
Last Day Last 3 Days
28/01G/e0n8e1ra5l:22:09 Alarm(s) off 1(1) Last Week
28/01B/a0t8ch1e4s:48:57 Archiving resumedLast Month
28/01/08 14:48:57 Local archiving automatically resumed 28/01L/o0g8in1s2:38:51
Archiving suspendeAdll History
28/01S/i0g8nin1g2s:38:51 Local archiving automatically suspe…
Figure 3.1.4f Message log page showing filters
MESSAGE TYPE FILTER
All Messages All messages are displayed
System
Only System messages and instrument alarms are listed
Alarms
Only alarm on/off and acknowledgement messages appear.
Power Up Displays power up messages only including Config Revision and Security revision. See `About’ (section
4.6.8) for more details.
General
Displays operator notes/custom messages etc.
HA029722 Issue 2 May 16
User guide Page 17
100 MM PAPERLESS GRAPHIC RECORDER
3.1.4 SUMMARY MENU (Cont.)
MESSAGE TYPE FILTER (Cont.)
Batches Logins Signings Audit trail Reports
Not applicable to this recorder model Lists only changes in login. Not applicable to this recorder model Not applicable to this recorder model Not applicable to this recorder model.
PERIOD FILTER
This picklist allows the user to select one of the following to define the
period of time that the message list is to encompass:
All History, Last Month (28 days), Last Week, Last 3 Days, Last Day or Last
Hour.
OPTION MENU
Touching a message (highlights yellow) calls the Option Menu* as shown in figure 3.1.4g, below.
Engineer
Group 1
15:24:36 28/01/08
All Messages
All History
Message Log: Group O1ption Menu
28/08/01 15:24:09 Alarm(s) on 1(1)
Note
28/01/08 15:23:21 Alarm(s) on 2(1)
28/01/08 15:22:56 Alarm(Esn) toeffr2H(1is) tory
28/01/08 15:22:09 Alarm(s) off 1(1)
28/01/08 14:48:57 ArchivinFgurlel sduemtaeidls
28/01/08 14:48:57 Local arcRhievifnrgesahutomatically resumed
28/01/08 12:38:51 Archiving suspended
28/01/08 12:38:51 Local archiving automatically suspe…
To call the Option Menu, touch the message (highlights yellow) or the Option key
Figure 3.1.4g Message Log options menu
Note
See section 3.5.
Enter history
Operating the Enter History key causes the recorder to display that page of history which
includes the highlighted message. See section 3.4.1 for details of trend history. When
in Trend history mode, operating the Message Log key calls that message log page which
contains those messages which are nearest the trend history cursor time.
Full details
If the highlighted message is wider than the display, the whole message can be displayed
by operating the `Full Details’ key.
Refresh/Earlier messages../Later messages..
`Refresh’ places (at the top of the screen), any messages, which have occurred since the
Message Log page was last entered, or since the last `Refresh’. If earlier or later messages
have been selected, then Refresh’ is replaced byEarlier messages..’ or
`Later messages..’
as appropriate, and operating the key calls the next or previously displayed group of 100
messages to the display respectively.
- See overleaf
User guide Page 18
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.1.4 SUMMARY MENU (Cont.) Message Log option menu (Cont.)
- The option menu can also be called by touching the option key. In this case:
a. Enter History calls the current Trend History display, as described in section 3.4.1, and
b. Because no message is highlighted, theFull Details’ key is not enabled, Notes: 1 SelectingEnter History’ whilst eitherEarlier Messages’ orLater Messages’ is highlighted calls the current History page.
2 If the Option Menu hastimed out’ leaving a message highlighted, and the option key is operated, then this is equivalent to reselecting the message. REMOVE MEDIA This key is provided to help ensure that any local memory storage device is removed only when it issafe’ to do so.
Touching the key results in either anOK to remove archive media’, or aDO NOT REMOVE Archive Media! message, as appropriate. See figure 3.1.4h
Caution Removal of Compact Flash cards whilst archiving is taking place can lead to permanent, irreparable damage to the device, rendering it unusable.
Archive Media
DO NOT REMOVE Archive Media!
OK to remove archive media Will advise when OK to remove…
Ok
Cancel
Figure 3.1.4h Remove archive media messages
HA029722 Issue 2 May 16
User guide Page 19
100 MM PAPERLESS GRAPHIC RECORDER
3.2 NAVIGATION KEYS
Below the display screen are six printed keys which allow the user to perform
various context-related tasks such as changing display mode (section 3.4),
accessing the recorder configuration, archiving data etc. In addition to this
set of keys, left and right arrow keys and open/close folder keys appear when
relevant.
Page up Page down
Left
Right
Option
Root
Close folder
Open folder
Left cursor
Right cursor
Figure 3.2 Navigation keys
3.2.1 Key functions Page up Page down Left arrow Right arrow Option Root
ROOT MENU KEYS Home Operator
File Remove Media
Go to View
Goto Group
Used, as appropriate, to recall the previous (higher level) display page, to
call the previous display mode and to scroll through previous text entries.
Where relevant, the function of this key is mimicked by the Close folder’ key. Used, where appropriate, to call a further (lower level) display page, to call the next display mode and to scroll through previous text entries. Where relevant, the function of this key is mimicked by theOpen folder’ key. Used
to navigate backwards through a text string when editing or to select the
previous channel whilst in configuration. Where relevant, the function of this
key is mimicked by the Left cursor’ key. Used to navigate forwards through a text string when editing or to select the next channel whilst in configuration. Where relevant, the function of this key is mimicked by the Right cursor’ key. Calls a pop-up Options menu allowing the user to carry out
functions such as entering/ quitting history, turning channel cycling on and
off etc. according to context. Calls the Root Menu’ as described below. To quit the Root menu, touch the root key again. Causes a return to theHome’ page (vertical trend display) from any page in
the recorder. Causes the top level Operator page to appear. The appearance of
this display is dictated by the security level that the recorder is set to,
and by the access level of the user. As despatched from the factory, the
recorder is in logged out’ mode and the Operator page contains only Archive’, Security’ andSystem’ keys. Further details appear in Access to configuration’ below. Allows the file system in that area of Flash memory that is accessible to the user, and the file system on any bulk storage device fitted, to be viewed. See section 5 for details. This key is provided to help ensure that any local memory storage device is removed only when it issafe’
to do so. Touching the key results in either an OK to remove archive media’, or aDO NOT REMOVE Archive Media! message, as appropriate. For more details
see section 3.1.4. Allows the user to select a display mode, as shown in
figure 3.2.1. As an alternative, display modes can be scrolled-through using
the up and down arrow navigation keys. Goto View also offers an alternative
means of entry to the Alarm Summary page described in section 3.1.4, and also
allows entry to the Message Log pages, described below. Not used on this
recorder model.
User guide Page 20
HA029722 Issue 2 May 16
3.2.1 KEY FUNCTIONS (Cont.)
100 MM PAPERLESS GRAPHIC RECORDER
Root Menu
Home
Operator
File
Remove Media
Goto View Goto Group
Goto View: Group 1
Alarm Summary
Message Log
Vertical Trend
Horizontal Trend
Vertical Bargraph Horizontal Bargraph
Numeric Page
Figure 3.2.1 Root menu with Goto View sub menu
ALARM SUMMARY The Root menu/Goto View/Alarm summary key calls the Alarm
summary page to the screen. Alternatively, Alarm summary can be selected from
the Summary menu. See section 3.1.4 for more details of the alarm summary
page.
MESSAGE LOG The Root menu/Goto View/Message log key calls the Message Log page
for to the screen. Alternatively, Message Log can be selected from the Summary
menu. See section 3.1.4 for full details of the message log.
HA029722 Issue 2 May 16
User guide Page 21
100 MM PAPERLESS GRAPHIC RECORDER
3.3 FIRST SWITCH-ON
When power is applied the recorder initialises, and once this process is
complete, the home page is displayed. It is unlikely that this will contain
any useful information because the input channels will not, as yet, have been
configured to suit the type of input signals being applied to them, as
described in section 4.
Notes:
1 There is no on/off switch associated with the recorder.
2 Date, time and the message Power Up’ are printed on the chart each time power is applied to the recorder, followed by a similar message givingConfig
Revision’ and `Security Revision’ (always zero for this recorder model.
3 A red line is drawn across the width of the chart at power up
The recorder has four security levels as follows:
Logged out
Operator Engineer
Service
No access to recorder configuration is possible. Only Archive, Login/security
and the System About’ functions can be accessed – via the root menu. As Logged out’, but alarms may be acknowledged. Accessed by entering `100′ as
the password (section 3.3.1, below). Full access to all recorder functions is
available.
Full access to all recorder functions and to areas of recorder memory for
diagnostic pur-
poses. For use only by Service Engineers.
User guide Page 22
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.3.1 Access to Configuration
1 As shown in figure 3.3.1a, once the recorder has initialised, touch the
current access level key 2 Touch the Logged out’ field and then touch Engineer’ from the resulting picklist. 3 Touch the blank Password area to
call the keyboard display (see figure 3.3.1b). 4 Touch 100′. The screen reverts to theHome’ page. 5
Operation of the Root key followed by a touch on the Operator key calls the
top level page allowing
access to the Archive, Save/Restore, Config, Security, Network and System
areas described in section 4 below.
1 Touch `current access level’ key Logged out
Login
Group 1
10:22:04 29/01/08
Select the required access level and enter the
password if required.
2
3
For Engineer’ level, touch the password area (when it appears) and enter 100. Clicking onOK’ causes the screen to go to the home page with the new access
level displayed in the `current access level’ key.
User ID Logged out Logged out Operator Engineer
Touch `logged out’ area …
… then touch access level required
ClosSeervice
Figure 3.3.1a Access to configuration
Note:
The login screen, above, can also be called by operating the Root menu, then
Operator’ thenSecurity’, then Login’. In such a case, the screen reverts to theOperator’ page rather than returning to the home page once login has
been achieved.
HA029722 Issue 2 May 16
User guide Page 23
100 MM PAPERLESS GRAPHIC RECORDER
3.3.1 ACCESS TO CONFIGURATION (Cont.)
TEXT STRING ENTRY
The keyboard which appears when the password area is touched is the same as
that which appears when any non-numeric text string entry is required (e.g.
channel descriptor). Figures 3.3.1b and 3.3.1c below are an attempt, within
the limitations of the illustrating process, to depict the available keyboards
and thus the available character set. Actual entry of the text string is by
touching the relevant keys.
When editing existing text strings, the existing text string appears
highlighted, and will be replaced in its entirety by the first character
entered. To avoid this, the left arrow key can be touched to `unhighlight’
it. The down and up arrow keys can be used to scroll through previously
entered text strings.
Immediately below the keyboard are six keys with the functions listed below.
When active, the background colour changes to yellow for as long as the key is
active.
Shift Once the shift key has been pressed, the next-entered letter appears as
a capital; subsequent letters are in lower case.
Caps When pressed, all subsequent letters appear as capital letters until the
Caps key is operated again BSpc This backspace key deletes character to the
left of the cursor. Ovr If selected, the next-entered character replaces
(overwrites) the existing character to the right of the
cursor position. If not selected, the next-entered character in inserted into
the existing text string at the cursor position. Ok Used to save the new text
string and to return to the page from which the keyboard was called. Cancel
Causes a return to the page from which the keyboard was called without saving
the new string.
Notes
1. The character on each display key is always a capital letter, whether or
not the actual character being entered is in capitals or lower case.
2. The cursor keys mimic the function of the left and right arrow Navigation
keys.
3. As an alternative, text may be entered using a suitable keyboard connected
via the USB port behind the access flap.
Cursor keys
Text string (all * for password)
**
Q
W
E
R
T
Y
U
I
OP
A
S
D
F
GH
J
K
L
°
Tabs show active keyboard (tab positions vary according to
context)
Z
X
C
V
B
NM
.
Alphabet Alphabet 2 Numeric Symbols
Shift Caps BSpc Ovr
Ok Cancel
Shift key
Caps Lock
Backspace Overprint
(shown active)
Figure 3.3.1b Alphabet 1 keyboard
User guide Page 24
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.3.1 ACCESS TO CONFIGURATION (Cont.) TEXT STRING ENTRY (CONT.)
HA029722 Issue 2 May 16
Figure 3.3.1c Alternative keyboards
User guide Page 25
100 MM PAPERLESS GRAPHIC RECORDER
3.4 DISPLAY MODES
The display modes described below allow the currently displayed group’s
process values (channels, totalisers etc.- known collectively as points) to be
displayed as vertical or horizontal chart’ traces, as vertical or horizontal bargraphs or as numeric values. The various display modes are cycled-through using the up/down arrow keys, or a specific mode (or view) can be selected from the Root MenuGoto View’ key. The Home key returns the user to the
Vertical Trend display from anywhere in the Operator or Configuration pages in
the recorder.
TREND HISTORY
Trend history, allows the user to review group history. The maximum amount
that can be reviewed depends on a number of factors, including how many points
are configured, how rapidly the traces are changing and so on. At a recording
rate of 20 mm/hour (see group configuration – section 4.3.2), with all
channels configured, a minimum of 30 day’s worth of traces is available for
viewing, provided that the group contents are not re-configured during this
period (in which case, the history starts at the end of the re-configuration).
The amount of trace visible on the screen depends on the recording rate, the
higher the rate, the less trace is visible at any one time.
Notes:
1. Trend history mode is available only for groups with Recording Enable’ enabled (Group configuration – section 4.3.2), and only for vertical, horizontal or circular trend dispplay modes. 2\. Trend history mode is vertical for vertical and horizontal for horizontal trend mode. 3. Channel cycling is inhibited in trend history mode. To increment the current channel, touch the faceplate. 4. Group faceplates are not displayed in trend history mode. 5. Operation of theRoot/Goto View/Message Log’ key (section 3.2.1), when in
history mode, displays a
message log page containing messages which occurred at or near the selected
cursor time.
To enter trend history mode, the option key can be used (as shown for vertical
trend mode in figure 3.4.1b), or the trace area of the screen can be
continuously touched until the screen blanks prior to re-drawing. A Preparing History, please wait’ message appears whilst the re-drawing calculation is taking place. Although tracing stops whilst trace history mode is active, no data is lost. Process Variable values are saved in the recorder memory. Alarms are still scanned-for and any associated action taken. The trend history display is similar to the real-time trend display, but with a dark background and with the addition of a slider control and arrow keys for selecting that part of trend history which is to be displayed. The controls are used as follows: 1\. Touching an arrow key causes the trace history to move an incremental amount. 2. Holding an arrow key continuously, causes continuous movement. 3. Touching and dragging the slider, whilst observing the time/date display, allows the user to select the sec- tion of history exactly. Touching the slider bar either side of the slider causes a page shift in the relevant direction. The Page up and Page down keys can also be used to provide this function. On first entry to trend history mode, the channel value and the time and date shown in the faceplate are those at the top (vertical trend) or right-hand (horizontal trend) edge of the chart. Touching the screen causes a cursor to appear at point of screen contact. This cursor can be touched and dragged to provide a reference point on the current trace. The displayed value date and time refer to the cursor intersection with the current channel. To return to real-time trending, the Option key is operated, followed byExit History’.
User guide Page 26
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.4 DISPLAY MODES (Cont.)
TIME CHANGE RECORDS
For vertical and horizontal trend modes a line is drawn across the width of
the chart whenever a time disconti-
nuity in the record occurs. These lines disappear if a configuration change is
made which causes group history to be lost (such as adding a channel to a
group).
Red line Blue line
Green line
A red line is drawn on the trend history chart at power up. A blue line indicates that recording has been disabled/enabled in Group Configuration (section 4.3.2), or by a recording job (section 4.7.9). A green line appears if there has been a time change as a result of a clock job (section 4.7.6), an SNTP synchronisation or by the operator physically changing the recorder time.
Note: Changes from standard time to daylight saving time and back again are not `green lined’ in this way.
3.4.1 Vertical Trend display
This display (figure 3.4.1b) shows each point in the display group as though
it were being traced on a white chart.
One of the channels is said to be the current’ orscale’ channel. This
channel is identified by its diamond shaped pen icon and by its descriptor,
digital value and scale being displayed on a faceplate’ across the full width of the screen, above the chart. If a channel is included in the display group but its status isnot good’ for some reason, then its pen icon is hollow.
Faceplates for all the group channels can be displayed, by using the
Faceplates On/Off key in the Option
menu. If selected `On’, faceplates (showing colour, descriptor, digital value
and units) for all the group’s channels appear either above the current
channel’s faceplate or, if there are too many to fit across the screen, at the
right hand edge of the screen. When necessary, a slider bar appears to allow
further (hidden) faceplates
to be viewed.
Each channel in the display group becomes the `current’ channel, in turn, for
approximately 10 seconds i.e. the channels are cycled-through, starting with
the lowest numbered channel. Once the final channel in the group has been
displayed for 10 seconds, the lowest numbered channel is returned to and the
sequence re-
peats. This scrolling process can be enabled or disabled using the Channel
Cycling On (Off) key in the Option
menu.
To select a particular channel to be the current channel, the relevant pen icon can be touched. To cycle through the channels manually, the faceplate area is touched repeatedly until the required channel is reached.
The Horizontal Trend display can be called using the down arrow key.
Alternatively, any enabled display mode can be selected using the Root Menu,
`Goto View’ key.
Option Menu
Option Key
Note Faceplates On/Off
See section 3.5 for `Operator Notes’ details
Channel Cycling Off
Enter History
HA029722 Issue 2 May 16
Figure 3.4.1a Option Menu (Typical)
User guide Page 27
100 MM PAPERLESS GRAPHIC RECORDER 3.4.1 VERTICAL TREND DISPLAY (Cont.)
User guide Page 28
Home
Engineer
Group 1
Channel descri…
0.7612V
Channel descriptor
0.0000
0.2000
0.4000
Trend display mode
10:22:04 29/01/08
Channel 2
42.3960 Deg C
0.7612 V
0.6000
0.8000
1.0000
29/01/08 10:21:10 Alarm(s) off 3(1)
10:21:37 29/01/08
10:20:57 29/01/08
10:20:17 29/01/08
Group faceplates (appear only if Faceplates are selected `On’ from option
menu). If there are too many faceplates to fit across the screen, they appear
down the right edge instead.
Faceplate for current channel. Touch and release faceplate to increment
channel
(or touch pen to select channel).
If Channel Cycle On: Current channel increments every 10 seconds.
Option Menu
Note
Faceplates On/Off
Channel Cycling On
Enter History
Trend History mode
Preparing History, please wait
Engineer
Group 1
Channel descriptor
0.7612 V
0.0000 0.2000
0.4000
0.6000
12:17:04 29/01/08 29/01/08 10:21:25
0.8000 1.0000
Cursor
Value at cursor date/time
29/01/08 10:21:10 Alarm(s) off 3(1)
10:21:37 29/01/08
10:20:57 29/01/08
10:20:17 29/01/08
10:19:37 29/01/08
Real time/date Cursor time/date (Touch faceplate to increment channel.)
Use arrow key to move minimum amount
Move slider to required date/time
Press bar to move one pageful Use arrow key to move minimum amount
Page backwards in time (show older data)
Page forwards in time (show newer data)
Option Menu
Note Exit History Message Log
Figure 3.4.1b Trend display mode and trend history mode
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.4.2 Horizontal Trend display
Entered from the Vertical Trend display by means of the down arrow key, or
selected via the Root Menu `Goto View’ key, this display mode (figure 3.4.2a)
is similar to the Vertical Trend display described in section 3.4.1 above,
except that the traces are produced horizontally rather than vertically.
Engineer
Group 1
Channel descriptor
0.7612 V
Faceplates for current channel. Touch either faceplate to increment channel
(or touch required pen icon)
Time (at adjacent grid line)
Non-current pen icons
15:21:01 29/01/08
15:23:01 29/01/08
29/01/08 10:21:10 Alarm(s) off 3(1)
15:25:04 29/01/08
1.000
Current pen icon Alarm mark (Abs High)
Bargraph
0.000
Message bar
Latest message
If this arrow head is displayed, then touching the message bar dislpays previous messages
Figure 3.4.2a Horizontal Trend Display
One of the channels is defined as being the current’ orscale’ channel and
this is identified on the chart by its pen icon being diamond shaped rather
than triangular as for non-current channels. If a channel is included
in the display group, but its status is not good’ for some reason, then its pen icon is hollow. Each channel in the display group becomes thecurrent’
channel, in turn, for approximately 10 seconds i.e. the channels are cycled-
through, starting with the lowest numbered channel. Once the final channel in
the group has been displayed for 10 seconds, the lowest numbered channel is
returned to and the sequence repeats. This scrolling
process can be stopped using the Channel Cycling key in the Option menu.
There are two faceplates associated with this display mode, one above the
chart’, showing the current channel’s descriptor and its digital value; the other – to the right of thechart’ – showing a bargraph representation of the
current channel’s value, together with a scale showing the low and high range
values for the channel. Touching either of these faceplates causes the current
channel number to increment. To select a particular channel to be the current
channel, the relevant pen icon can be touched. In either case, the bargraph
and the background colour of the channel descriptor take the colour of the new
current channel.
Touching the trace for a few seconds, or using the Option key then `Enter History’ calls the Horizontal trend history page. See section 3.4, above for more details.
Time and date are printed on the `chart’ immediately to the right of grid lines, and it is to these grid lines that the printed time and date relate.
HA029722 Issue 2 May 16
User guide Page 29
100 MM PAPERLESS GRAPHIC RECORDER
3.4.2 HORIZONTAL TREND MODE (Cont.)
Below the chart’ is a message bar, containing the latest message. If there is more than one message, an arrow head icon appears near the right-hand end of the message bar. If this arrow head appears, then touching the message bar calls a pop-up box (figure 3.4.2b) which displays the latest messages. If there are more messages than can be displayed in the box, a slider control appears, which can be used to access previous messages, up to a total of 60 messages. Further messages, cause the oldest messages to be discarded to keep the total to 60. Note: At power-up, only those messages which occurred within thetime width’
of the page are displayed
Engineer
Group 1
ChVanienewl dMesecrsispatogres
0.7612 V
29/01/08 16:14:09 Alarm(s) off 1(1)
29/01/08 16:12:09 Alarms(s) on 1(1)
29/01/08 16:11:21 Alarm(s) on 2(1)
29/01/08 16:10:56 Alarm(s) off 2(1)
29/01/08 16:10:09 Alarm(s) off 1(1)
29/01/08 16:08:09 Alarms(s) on 1(1)
29/01/08 15:53:01 Alarm(s) off 3(4)
29/01/08 15:13:07 Alarm(s) on 3(4)
29/01/08 15:07:01Alarm(s) off 1(1)
29/01/08 15:05:01 Alarms(s) on 1(1)
29/01/08 15:03:21 Alarm(s) on 2(1)
15:21:01 29/01/08
15:23:01
Ok 29/01/08
29/01/08 10:21:10 Alarm(s) off 3(1)
15:25:04 29/01/08
1.000
0.000
Figure 3.4.2b Horizontal Trend mode message dialogue box
The vertical bargraph mode can be called by using the down arrow key.
Alternatively, a new display mode can be selected using the Root Menu, `Goto
View’ key.
User guide Page 30
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.4.3 Vertical bargraph
Entered from Horizontal Trend mode by means of the down arrow key, or selected
from the Root Menu Goto View’ key, this display mode shows the Process Variable (PV) values as vertical bars with faceplates containing digital values and alarm data. For one or two channels, the faceplates appear above the bars. For more channels, the faceplates appear at the right hand edge of the display Operation of the option key calls the Option menu display for this display page, allowing faceplates to be selected on or off. This feature is available for vertical trend and vertical bargraph displays only. To call the horizontal bargraph display mode, use the down arrow key. Alternatively, a display mode can be selected using the Root Menu,Goto View’
key.
Trend history mode is not available from this display mode.
As the number of PVs increases, the bars get narrower. As the bars get
narrower, so the scale values become truncated as shown in figure 3.4.3. The
bars have a set minimum width, and if the total number of points in the group
cannot be displayed within the width of the screen, a horizontal scroll bar
appears, allowing `hidden’ bars to be viewed. Similarly, the faceplates reduce
in height to a minimum readable height. If there are more point faceplates
than can be accommodated within the height of the screen, a vertical scroll
bar appears, as shown in the figure, allowing hidden faceplates to be
displayed as required.
Engineer
Group 1
11:00:45 30/01/08
Channel 1
0.7612V
Channel 2
42.3960 Deg C
1.0000
100.0000
0.0000
0.0000
Engineer
Group 1
1.00 100 100 150 150 150 Channel 1 0.7612 V
11:00:45 30/01/08
Channel 2 42.3960 Deg C
Channel 3 32.8853 Deg C
Channel 4 107.5210 Deg C
Channel 5 107.1660 Deg C
Channel 6
0.00 0.00 0.00 0.00 0.00 0.00
103.9883 Deg C
Faceplates above (one or two points)
Faceplates to the side (three or more points)
Figure 3.4.3 Vertical bargraph displays
HA029722 Issue 2 May 16
User guide Page 31
100 MM PAPERLESS GRAPHIC RECORDER
3.4.4 Horizontal bargraph Entered from Vertical bargraph by means of the down
arrow key, or selected using the Root Menu Goto View’ key, this display mode shows the Process Variable (PV) values as horizontal bars with digital values and alarm data displayed, as shown in figure 3.4.4 Note The maximum number of points that can be displayed is 6. If more than six points are enabled scroll bar appears allowing currently hidden channels to be accessed. Trend history mode is not available from this display mode. To call numeric display mode, use the down arrow key. Alternatively, the display mode can be selected using the Root Menu,Goto View’ key.
Engineer
Channel 1
0.0000
Channel 2
0.0000
Channel 3
0.0000
Channel 4
0.0000
Channel 5
0.0000
Channel 6
0.0000
Maths 1
1000.0000
Group 1
11:00:45 30/01/08
1.0000 100.0000 100.0000 150.0000 150.0000 150.0000
0.00 0.00 0.00 0.002000.0000
Figure 3.4.4 Horizontal bargraph displays
User guide Page 32
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
3.4.5 Numeric display
Entered from Horizontal bargraph mode by means of the down arrow key, or
selected using the Root Menu Goto View’ key, this display mode shows the Process Variable (PV) values as digital values. The format (which is automatically selected) is based on the number of channels in the display group. Figure 3.4.5 shows typical examples of the one and two column versions of this display mode respectively. Within each version, the process variable display areas expand or contract to fill the screen. The display for 5 to 10 points is similar to that shown forMore than 10 points’, below, but without
the scroll bar.
Trend history mode is not available from this display mode.
Operation of the down arrow key returns to the Vertical Trend Display mode
described in section 3.4.1 above. Alternatively, a display mode can be
selected using the Root Menu, `Goto View’ key.
Engineer
Group 1
Channel 1
Channel 2
Channel 3
Channel 4
11:00:45 30/01/08
0.7612 V
42.3960 deg C
32.8853 deg C
107.5210 deg C
Engineer
Group 1
Channel 1 0.7612 V
Channel 3 32.8853 deg c
Channel 5 107.1660 deg c
Maths 1 1710.03 l/min
Maths 3 2031.49 l/min
Maths 5 34.24 mins
Channel 2 42.3960 V
11:00:45 30/01/08
Channel 4 107.5210 deg c
Channel 6 103.9883 deg c
Maths 2 903.08 l/min
Maths 4 31.39 mins
Maths 6 29.74 mins
One to four points
More than 10 points
Figure 3.4.5 Numeric display mode examples
HA029722 Issue 2 May 16
User guide Page 33
100 MM PAPERLESS GRAPHIC RECORDER
3.5 OPERATOR NOTES
Note: Operator notes should not be confused with similar messages, (described
in section 4.3.6), which appear as a result of job action.
It is possible for the user to enter a note, of up to 120 characters, at any
time, from any display page (not from configuration pages). Each note is
associated with the current display group and becomes a part of that group’s
history. The notes appear on vertical and horizontal trend displays only,
although they can be entered in any display mode.
The note appears on the chart and in the Message Log, preceded by the date,
time and login level, as shown in the first example below.
30/01/08 15:46:11 Engineer, New Spray nozzles fitted to Line A, Tube 1.
Date and time Access level
Note
To enter a Note:
1. Press the Option key, then the `Note’ key 2. Touch the note area of the
resulting pop-up display (see note below). 3. Enter the required text of up to
120 characters (spaces are also counted as characters). Press Ok when
finished. 4. View the note and
a. press the Ok button to enter the note OR b. re-touch the text area to edit
the note OR c. press the Cancel key to quit note entry.
Option Menu
Note
Note
Option Key
Faceplates On/Off
Channel Cycling On
Operator Notes list. Appears if noteEnatreeraHiissttooruyched continuously for
2 seconds (approx). List entries are made in Instrument Configuration (section
4.3.1)
Operator Note
00:0A:8D:00:20:A0 AM Shift started AM Shift finished PM Shift started PM Shift
finished
Figure 3.5 Access to Note entry page
Note: Touching the note area continuously for two seconds or more, causes a
list of pre-defined messages to appear. Touching one of these messages selects
it as the operator note, which can then be edited in the normal way (if
required) before the OK key is operated. There are a maximum of 13 predefined
messages, 12 of which are user editable in the Configuration/instrument menu
(section 4.3.1), the 13th being the non-editable MAC address of the recorder.
User guide Page 34
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
4 SETTING UP THE RECORDER
As described in the `Access to Configuration’ (section 3.3.1) above, the setting-up of the recorder is divided into the following areas:
Archive Save/R..
Config Security Network System
Section 4.1 – Allows manual archiving of data to a memory device or to a
remote host (FTP transfer).
Section 4.2 – Allows new configurations to be created and saved, and saved
configurations to be `restored’. Save/Restore also allows the importing and
exporting of User Linearisation Tables and, if the relevant options are
fitted, User Screens and Printer Drivers. Section 4.3 – This is the major
channel/alarm option etc. area of configuration. Section 4.4 – Allows the user
to log in.
Section 4.5 – This area sets up the IP address/host names etc. used in FTP
transfer, Bridge and SNTP applications.
Section 4.6 – Allows
a) Time and date to be set (Clock).
b) Language, date/time format, time zone, and daylight saving start and finish
dates to be set (Locale).
c) Software upgrades to be carried out (Upgrade).
d) Input channels to be adjusted for errors in transducer inputs (Input
Adjust).
e) A Network diagnostics page to be displayed (Ethernet diagnostics).
f) Configuration items (e.g. input channels) to be copied, to speed up
configuration (Copy). g) Search criteria to be entered to allow the user to
locate trigger sources for a specific job
(Job search).
hj) Details of the hardware and software associated with the recorder to be
displayed (About).
Note: In all the following descriptions, if a change is made to a menu item, then the item text changes to red, until it is `applied’
HA029722 Issue 2 May 16
User guide Page 35
100 MM PAPERLESS GRAPHIC RECORDER
4.1 ARCHIVE
Note: The archiving functions described below can also be initiated by job
action – see section 4.7.11.
4.1.1 Local Archive Caution
Removal of the memory device whilst archiving is in progress causes
irreparable damage to the filing structure on the device, rendering it
unusable. For this reason, archiving should be suspended before the device is
removed. It is strongly recommended that the `Remove Media’ facility described
in section 3.1.4 (Summary menu) be used to ensure that it is safe to remove
the memory device.
Archive Save/R.. Config Security Network System
Local Remote
Last Archive 30/01/08 11:02:42 Media mediacard Select Media card or USB port
Section 4.1.2
Bring Archive Up To Date
Archive Last Hour
Archive Last Day
Archive Last 7 Days
Archive Last 31 Days
Archive All
Suspend Archiving
Cancel Archive
Archive Transfer Inactive
Media Full 29/02/2008 00:34:57
Media Size 31954944
Bytes
Free Space 28786688
Bytes
Figure 4.1.1 Local archive configuration
Local archive allows the user to initiate data transfer to the device defined
in the Media’ picklist ifArchive to Media’ is enabled (Group configuration
– section 4.3.2). Archiving is initiated by touching the relevant archive
period key (e.g. Last Day’). The memory device can be selected as `mediacard’
(the integral Compact Flash or SD card), or a USB port can be selected if, for
example, a memory stick is to be the destination device. USB-
front is located behind the flap below the screen. USB 1 and USB 2 ports are
not available for this recorder model.
Archiving starts as soon as the selection is made, and cannot be stopped until
completed, unless the Cancel
Archive key is operated, in which case the archive will be stopped after a
confirmatory message has been responded to. The Cancel/Suspend key is active
only for `Engineer level logins.
User guide Page 36
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
4.1.1 LOCAL ARCHIVE (Cont.)
BRING ARCHIVE UP TO DATE This causes the recorder to archive all history files
created since the last manual or automatic (section 4.3.4) archive.
ARCHIVE ALL This causes the recorder to archive all its history files.
If the memory device becomes full before archiving is complete, archiving
pauses and a pop-up request appears, asking for a replacement. If this request
is not responded to within 10 minutes of its appearance, archiving is aborted.
Unattended archiving can be paused by the user (e.g. to change media without
losing data) by operating the Suspend Archiving’ /Resume Archiving’ button.
Any archiving in progress is allowed to complete before the Suspend Archiving’ request takes effect. Transfer activity is indicated in the Archive transfer’ window.
Below the selection buttons are a number of status windows relating to the
selected memory device. Media Full’ is an estimate, based on the current configuration, of when the memory device will become full. The meanings of the Media Size’ and `Free Space’ values are self evident.
If automatic archiving is active (section 4.3.4), then automatic and manual
archives will operate on a first come-first served basis. Some files will be
saved twice in such a circumstance, the later archive’s files overwriting any
earlier archive’s files which have the same name.
HA029722 Issue 2 May 16
User guide Page 37
100 MM PAPERLESS GRAPHIC RECORDER
4.1.2 Remote archiving (FTP transfer) This allows archiving of recorder files,
if Archive via FTP’ is enabled, to a remote computer, connected (using the RJ45 telephone type connector at the rear of the recorder) either directly, or via a network .Archive via FTP’ is enabled/disabled as part of Group
configuration – section 4.3.2.
In order to carry out a successful transfer, details of the remote host must
be entered in the Archive section of the Config’ menu (section 4.3.4). Note: An FTP server must be running on the remote host. Figure 4.1.2 shows the menu for remote archiving. The Archive last hour/day etc. keys allow the user to determine which files are to be archived. Selection ofBring Archive Up To Date’ causes the recorder to select
whichever of the Last Hour/Last Day etc. categories is appropriate in order to
bring the archive up to date. The Last Archive’ window shows the time and date of the previous archive. The Archive Transfer window shows archive status asActive’ or `Inactive’.
Archive Save/R.. Config Security Network System
Local Remote
Last Archive 29/01/2008 10:00:00 Bring Archive Up To Date
Section 4.1.1
Archive Last Hour
Archive Last Day
Archive Last 7 Days
Archive Last 31 days
Archive All
Cancel Archive Archive Transfer Inactive
Figure 4.1.2 Remote archive strategy configuration
When connecting, the User Name is Engineer’. the password is 100. The IP address is found by looking in the Network/Address area (section 4.5.1), and the instrument identifier is to be found in the Config,,,/Instrument area (section 4.3.1). Notes: 1\. When accessing files using Microsoft® Internet Explorer, the address (URL) field can be in one of two forms: a ftp://<instrument IP address>. This allows the user to log in as the anonymous user (if the instrument has any account withRemote user name’ set to `Anonymous’ and a blank password). b
ftp://
2. For IE5 users only: Microsoft® Internet Explorer displays, by default,
history files only. To exit the history folder, either uncheck the
Tools/Internet Options/Advanced/Browsing/”Enable folder view for FTP sites”
option, or check the Tools/Internet Options/Advanced/Browsing/”Use Web based
FTP” option.
User guide Page 38
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
4.2 SAVE / RESTORE
As shown in figure 4.2a, touching the `Save/R..’ key calls the picklist: Save,
Restore, New and Text.
Archive Save/R.. Config Security Network System
Save Restore New Text
Save as 6100E File Name config
Save
File Name config Save As Text
Configuration Data Security Data Network Data Screen Data
New/Default
Configuration Data Security Data Network Data Screen Data
Restore
File Name config
Figure 4.2a Save/Restore menu
Where a file name is required, then, if the displayed file name is suitable,
operation of the Save’ orRestore’, key will initiate the action. If,
instead, a file name has to be entered, this is carried out as follows:
Touching the filename window causes a pop-up menu to appear, giving a list of
Volumes’ in the Flash memory or on the memory device (if inserted). Figure 4.2b shows an imaginary Volume contents list, displayed by touching the name user’, then operating the down arrow or `open folder’ key. (See section 5,
below for more details). Once the correct folder is open, either select an
existing file, or enter a new filename, by touching the FileName window and
entering the name using the pop-up keyboard(s) as described in section 3.3.1
above. Operation of the Save/Restore key initiates the action.
user
cal config Filter1a lib sdb user
Type
Folder Folder Config Folder Folder Folder
FileName: Filter1b
Hide
Date
Bytes
31/01/08 16:19:46
28/12/07 10:27:13
29/12/07 10:22:23 4445
29/01/08 10:23:14
30/01/08 14:01:08
31/01/08 15:41:30
Save Cancel
Figure 4.2b Typical volume contents page
HA029722 Issue 2 May 16
User guide Page 39
100 MM PAPERLESS GRAPHIC RECORDER
4.2.1 Save Touching this item allows the current configuration to be saved in
the recorder’s memory. Files saved in this way are not in a readable’ format and are used only for archive /security purposes or for transfer to another, similar, recorder. SAVE AS This selection box allows a configuration to be saved, if required, in a format suitable for importing into previous recorder models. The default is always the current instrument. 4.2.2 Restore Touching this item allows the user to select or type-in a previously saved configuration file name, which will then be used as the current configuration. Touching theRestore’ key completes the operation.
Check boxes allow one or both of Configuration Data, and Network data to be
chosen for the restore function. Security data and Screen data are not
applicable to this recorder model.
Note If archiving is in progress when a Restore’ is requested, the Restore operation will be delayed until the archive is complete (maybe several minutes). If required, theCancel Archive’ key (section 4.1 above) can be
used to speed up the Restore process, at the cost of losing the archive data.
4.2.3 New Touching this item causes the factory entered default configuration
to be loaded for use, or for editing. Operation of the New/Default key
completes the operation. Tick boxes allow one or both of Configuration Data,
and Network data to be chosen for the restore default function; only those
items which are ticked are replaced by default values. Security data and
Screen data are not applicable to this recorder model.
4.2.4 Text This is identical to the `Save’ function described above, but the
configuration is saved in ASCII format, and can be transferred to a computer
and read, printed etc. as required. It is not possible, using this means, to
modify the configuration and then re-load it.
User guide Page 40
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
4.3 CONFIG KEY
Touching this key calls the top level configuration pick list: Instrument,
Groups, Channels, Archive, Events, Messages, Maths, Totalisers, Counters,
Timers.
Notes: 1. Figure 4.3b gives an overview of the configuration menus. 2. If an
option is not fitted, it does not appear in the above list.
When making changes to the configuration the name of each changed parameter is
displayed in red (instead of the normal black) until the Apply/Discard’ key has been operated. For example, in channel configuration, if a thermocouple were to be changed from Type J to Type K,Lin Type’ would appear in red,
until the Apply key is operated.
Should an attempt be made to leave configuration with unsaved changes, a
warning message appears, (Figure 4.3a) allowing the user to apply the changes,
to discard the changes or to return to configuration (Cancel).
Config
Data Has Been Modified
Apply Discard Cancel
Figure 4.3a `Data modified’ warning
HA029722 Issue 2 May 16
User guide Page 41
HA029722 Issue 2 May 16
User guide Page 42
Archive Save/R.. Config Security Network System
Instrument Groups Channels Archive Events
See sheet 2 for further items
Events (Section 4.3.5)
Event Number 1) Event 1 Source 1 Alarm on Group On Group 1) Group 1 Source 2
Point Alarm On Math 3 Alarm 2
Source 1 Sense Source 1 Operator And
Source 2 Sense Not Source 2 Descriptor Event 1
Job Number 1 Category No Action Apply Discard
Remote
Compression Normal
Flash Size 8
Mb
Shortest Trend History G r o u p 1 Duration 3 . 7 1
Days
Show Remote settings
Archive to Remote None
Ftp File format Binary
Remote path / r e c o r d e r / G r o u p 1
Primary remote host 0.0.0.0 Primary login name a n o n y m o u s
Primary password Retype password
Secondary remote host 0.0.0.0 Secondary login name a n o n y m o u s
Secondary password Retype password
Apply Discard
Instrument (Section 4.3.1)
Channels (Section 4.3.3)
Archive (Section 4.3.4)
Channel Number 1) TurbineTempA
Value 5.0002
07/04/05 08:46:45
Input Type Thermocouple
Lin Type Type K
Range Low 0
C
Range High 100
C
Range Units C Scaled
Offset 0
V
Scale Type None
Filter None
Break Response None
Cold Junction Type Off Descriptor TurbineTempA
Spanned
Zone Low 0
%
Zone High 100
%
PV Format Numeric
Max Decimal Digits 4
Colour 26 Alarm Number 1
Enable Off
Job Number 1
Category No Action
Apply Discard
Local
Compression Normal
Flash Size 8
Mb
Shortest Trend History G r o u p 1
Duration 3 . 7 1
Days
Show Local settings Media mediacard
Archive to Media None
Media file format Binary
On Media Full Overwrite
Media Size 30.4746094 Mb
Removable Media Capacity 3 3 . 1 8
Days
Media Full event limit 100 %
Apply Discard
Figure 4.3b Configuration menu overview sheet 1
Instrument Name Instrument
Normal Display 100 %
Saver Display 50 %
Save After 30 Minutes
Modbus Address1
Modbus Security Disabled
= Disabled
Comms Channel Timeout0 s
Preset Hour 10 2
Preset Minute0 0
Disable Warning Dialogs
Show Operator Notes List
Apply Discard
Groups (Section 4.3.2)
Trend Units mm/hr Descriptor Group 1
Trend Speed 1,200 Trend Interval 1
Grid Type From Point from Channel 3
Recording Enable Recording Speed 1,200 Recording Interval 1 Trend History
Duration 25.96 Archive to Media Enable Archive via FTP Enable
Alarm Message Ack Message Point Type Channel
Selection 1-3,7,9,11-20
Enable
mm/ hr s
mm/ hr s Days
Disable
TurbineTempA TurbineTempB
Etc.
Apply
List of all available points (input channels, maths channels, totalisers
etc.).
Discard
4.3 CONFIG KEY (Cont.)
100 MM PAPERLESS GRAPHIC RECORDER
4.3 CONFIG KEY (Cont.)
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
Archive Save/R.. Config Security Network System
Messages See sheet 1 for other
items Maths
Totalisers
Counters
ConfigOptions (Section 4.3.11)
Timers Options
Messages (Section 4.3.6)
Message Number 1) The value of
Message The value of {1} = {2} & {3} = {4}, {5}
Replace {1} with Source Descriptor Replace {2} with Source Value
Apply Discard
Fitted channels 6 Virtual channels 12/36
Maths 6 Totalisers 3 Counters 3 Six Channel 6100E Enabled Relay Boards 1
(currently 0) Relays on Board 1 3
Apply Discard
Autoconfigure
Timers Section 4.3.10
Timer number 1) Timer 1 Enable
Remaining 00:00:00 Repeat in 00:00:00
Reset now Start now
These buttons appear only after ‘Apply’ has been operated
Descriptor Timer 1 Self start Date Any Month Any Hour Midnight Minute Any
Second Any Duration 60
Repeat after 0 Job Number 1
Category No Action
These fields appear only if ‘Self start’ is enabled.
Seconds Seconds
Apply Discard
Counters (option) Section 4.3.9
Counter number 1) Counter 1 Enable Value OFF Units Units Preset 0
Units Units
Preset now
Descriptor Counter 1 Scale Low 0 Scale High 1 Zone Low 0 Zone High 100 Scale
Type None
Colour 0 Alarm Number 1
Enable Off Job Number 1
Category No Action
Units Units % %
Apply Discard
Totalisers (option) Section 4.3.8
Totaliser Number 1) Totaliser 1 Enable Value 123456 Total of Channel 1
Low cut off 0 High cut off 999999
Units Units Preset 0
Units (totaliser)
ch units ch units Units (totaliser)
Preset now
Period scaler 1 Unit scaler 1 Descriptor Totaliser 1 Scale Low 0 Scale High 1
Zone Low 1 Zone High 100 Scale Type None PV format Numeric
Max Decimal Digits 4 Colour 0
Alarm Number 1 Enable Off
Job Number 1 Category No Action
Units (totaliser) Units (totaliser)
% %
Apply Discard
Maths (option) Section 4.3.7
Maths Number 1) Math 1 Value 32.65
Function Add Add Channel 1 to Channel 2
Units l/min Descriptor 1) Math 1 Scale Low 0 Scale high 60
Zone low 0 Zone high 100 Scale Type None PV Format Numeric Max Decimal Digits
2
Colour 26 Alarm Number 1
Enable Off Job Number 1
Category No Action
Apply Discard
l/min
Mins Mins % %
User guide Page 43
Figure 4.3b Configuration menu overview sheet 2
100 MM PAPERLESS GRAPHIC RECORDER
4.3.1 Instrument configuration
Instrument Name Instrument
Normal Display 100 %
Saver Display 50 %
Save After 30 Minutes
Modbus Address 1 Modbus Security Disabled Comms Channel Timeout 0 s
= Disabled
Preset Hour 10 2
Preset Minute 0
Disable Warning Dialogs
Show Operator Notes List
MAC Address 00:0A:8D:00:20:A0
Operator Note 1 AM Shift started
Operator Note 12 Apply Discard
Figure 4.3.1 Instrument Configuration menu
These fields appear only if ‘Show Operator Notes List’ is enabled
INSTRUMENT NAME
Allows the entry of an alphanumeric name for the recorder, up to 20 characters
long. See section 3.3.1 for text entry techniques.
NORMAL/SAVER DISPLAY Allows normal and `saver’ display brightnesses to be defined. Defaults are Normal = 100%; Saver = 50%
SAVE AFTER
The number of minutes (between 1 and 99 inclusive), which are to elapse after
a screen operation, before the screen brightness changes from normal’ to saver’. Default is 30 minutes.
MODBUS ADDRESS
Allows a Modbus address between 1 and 247 to be set up, for use when the
instrument is acting as a Modbus slave.
MODBUS SECURITY DISABLED
When using MODBUS, it is possible, by `checking’ this field to allow a host
computer to access the recorder without its first having to supply a valid
User name and Password. This box must be checked if this unit is acting as a
Modbus slave in order for the unit to be detected. Once communications have
been established, Modbus security can be enabled, providing that the Slave’s
Remote user name and password have been entered at the Master. See also
section 6.2.4.
COMMS CHANNEL TIMEOUT
Allows a number of seconds (between 1 and 999) to be entered. If none of the
channels set to `Comms’ is communicated with, within this period, an event
source (Comms channel timeout) is set, and remains set until the next
communication. An entry of 0 disables the time out.
User guide Page 44
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
4.3.1 INSTRUMENT CONFIGURATION (Cont.)
PRESET HOUR Enter an hours number between 0 and 23 for use with Clock Job –
Preset clock.
PRESET MINUTE Enter a minutes number between 0 and 59 for use with Clock Job –
Preset clock.
Note: See section 4.7 for a description of recorder jobs, and section 4.5.1
for further details of time synchronisation.
DISABLE WARNING DIALOGS Checking this box prevents instrument alarm messages
from appearing on the screen.
SHOW OPERATOR NOTES LIST Enabling this field produces a list of 13 entries
which can be used in Operator Notes. The first entry is the MAC address of the
recorder and is not editable. The remaining 12 entries (of up to 60 characters
each) are freely editable.
Any one of these predefined notes can be selected (as described in section
3.5) by touching the Operator Note area continuously for two seconds, then
touching the required note from the picklist which appears. Once selected the
predefined note can be edited before use, like a normal Operator Note. Such
editing does not affect the original note entered here in Instrument
Configuration.
HA029722 Issue 2 May 16
User guide Page 45
100 MM PAPERLESS GRAPHIC RECORDER
4.3.2 Group configuration Group configuration allows the user to define the
following: a Group trend speed/interval b Group recording speed/interval c
Group descriptor d Group content e Chart grid divisions
The production of alarm messages and the saving of group data to Flash memory,
to removable memory device and/or to remote computer (FTP transfer) can also
be enabled / disabled from this menu.
Trend Units mm/hr Descriptor Group 1
Trend Speed 1,200 Trend Interval 1
Grid Type From Point from Channel 3
Recording Enable Recording Speed 1,200 Recording Interval 1 Trend History
Duration 2.53 Archive to Media Enable Archive via FTP Enable
Alarm Message Ack Message Point Type Totaliser Selection 1-3,5,7,9
Enable
Select mm/ hr or in/hr
mm/ hr s
Select None, Linear, Log or ‘From Point’
mm/ hr s Days
Editable only if ‘Recording Enable’ is enabled.
= Enabled
Disable
TurbineTempA TurbineTempB
Etc.
Apply
List of all available points (input channels, maths channels, totalisers
etc.).
Discard
Figure 4.3.2a Group configuration menu
Grid Type Linear Grid Divisions – Major 5 Grid Divisions – Minor 1
Grid Type Log Grid Decades 5
TREND UNITS
Allows mm/hr or inches per hour to be selected for the `chart’ speed.
Automatically converts the trend speed field below.
DESCRIPTOR Allows the group name to be edited. See section 3.3.1 for text entry techniques.
TREND SPEED/TREND INTERVAL
Allows the `chart’ speed to be selected either as mm or in per hour, or as an
interval. Entering a value in one field automatically converts the value in
the other field. A trend interval of N seconds is equivalent to 1200/N mm/hr
chart speed; a chart speed of P mm/hr is equivalent to a trend interval of
1200/P seconds.
User guide Page 46
HA029722 Issue 2 May 16
100 MM PAPERLESS GRAPHIC RECORDER
4.3.2 GROUP CONFIGURATION (Cont.) GRID TYPE
Grid type allows the chart grid type to be defined for the group being
configured. This is not necessarily related to channel scale (section 4.3.3),
unless From point’ is selected, when the grid matches the scale of the selected point. NONE No chart grid is traced. LINEAR The chart grid is linear, with the major and minor divisions defined by the fields Grid Divisions – Major and Minor, which appear ifLinear’ is selected as grid type. Figure
4.3.2b below, defines major and minor divisions. LOG The chart grid is
logarithmic, with the number of decades being selected in the Grid Decades’ field which appears ifLog’ is selected as Grid Type. Figure 4.3.2b gives an
exam
References
- Temperature Control, Process Control, Measurement and Data Recording Solutions | Eurotherm
- Contact Us | Eurotherm
- The Modbus Organization
- timeanddate.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>