Artemide Tolomeo Midi Tavolo LED Desk Lamp Installation Guide
- June 9, 2024
- Artemide
Table of Contents
Artemide Tolomeo Micro LED Table Lamp
WARNING
- Before any operation on the fixture, disconnect the power supply. The fixture can not be supplied by an outlet provided with dimmer.
- TABLE BASE INSTRUCTIONS: Insert fixture body A into base B (fig.1). Turn base B upside down, position bush C washer D and lock with screw E (fig.2). Act on two ring nuts F to increase or decrease the stiffness of the fixture (fig. 3).
- WALL INSTRUCTIONS (fig. 4): Fix support G to the wall. Insert fixture body A into the proper seat by rotating and pressing it downward.
- HOLDFAST INSTRUCTIONS (fig. 5): Fix clamp H by means of screw I. Insert fixture body A into the proper seat by rotating and pressing it downward.
- FIXED TABLE INSTRUCTIONS (fig. 6): Make a hole (diameter 18.5-19.5mm) in the chosen flat surface, insert support L and lock ring nut M. Insert fixture body A into the proper seat by rotating and pressing it downward. N.B.: Do not use nuts and bolts supplied with the base.
- FLOOR INSTRUCTIONS: Insert stem N into base O and lock it by means of the washer and screw P. Position the three wire holders Q on stem N. Insert lamp body A into its seat by rotating and pressing downwards. Make the feeding cable go through wire holders Q.
WARNING: Provide the transformer with the proper outlet adapter. Before connecting the transformer to the outlet, check that the rated voltage marked on it is the same of the network one. No type of connection between fixtures and transformers/outlets different from the ones defined by ARTEMIDE is allowed.
OPERATION
The fixture is provided with a dimmer for the regulaion of the light
intensity.
To turn the fixture on, just touch the central part of switch R located on the
feeding cable.
Keep pressed switch R to regulate the light intensity up to the desired level
or up to the maximum level. Another long pressure of switch R inverts the
regulation direction of the
light intensity toward the minimum. Turn the fixture off by acting on switch
R. When turning the fixture on the same light intensity set before the turning
off is produced again.
LED REPLACEMENT
The fixture is provided with light source having a long life. Anyway, if the
led must be replaced, this operation must be carried out only by our
specialized staff.
Therefore, we recommend contacting the nearest dealer.
For the addresses of Artemide dealers in the world, visit our website:
www.artemide.com. CLEANING INFORMATION: Only use a wet cloth and neutral non-
abrasive detergent in order to clean the fixture.
General warnings for indoor light fittings
- Tutti i prodotti ARTEMIDE che rientrano nell’ambito di applicazione della direttiva europea bassa tensione B.T. 2006/95/CE e della direttiva europea compatibilità elettromagnetica E.M.C. 2004/108/CE soddisfano i requisiti richiesti e recano la marcatura “ ”.
- All ARTEMIDE products falling within the range of application of the European low voltage directive B.T. 2006/95/CE and of the European electromagnetic compatibility E.M.C. directive 2004/108/EC meet the required specifications and bear “ ” labelling.
- The fixtures in class must be supplied with a transformer in complaince with the regulations in force.
- ARTEMIDE spa does not shoulder any responsibilities for products which are modified without prior authorisation.
- For the replacement of the power supply cable, please contact ARTEMIDE service centre
- Warning: this equipment is guaranteed only when used as indicated in these instructions. Therefore they should be kept for future reference.
In case of complaint, please quote number
Via Bergamo, 18
I-20010 Pregnana M.se (MI) – ITALIA
t. +39 02.935.18.1 f. +39 02.935.90.254-496
info@artemide.com
www.artemide.com
P. Iva IT 00846890150
References
- Independent Drone Exchange – All about Drones, Quadcopters and Tricopters
- Mide Technology Engineering Research & Development
- Artemide - Home
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>