Trust TRANSMITTER AWRT-1000 Wireless Rotary Dimmer User Manual

June 9, 2024
Trust

Trust TRANSMITTER AWRT-1000 Wireless Rotary Dimmer
Trust TRANSMITTER AWRT-1000 Wireless Rotary Dimmer

1. Insert/replace the battery

Insert/replace the battery

  • A Remove the back plate with a flat screwdriver by placing it at the bottom between the back and front plate of the rotary dimmer
  • B Place a CR2032 battery in the rotary dimmer
  • C Click the rotary dimmer back on the back plate. When replacing the back plate, make sure that the arrows on the back plate and in the rotary dimmer both point up.

2. Send ON-OFF signal

  • A Press the button on the rotary dimmer 1x shortly to send an ON signal. The LED on the dimmer flashes 1x green.
  • B Press the button on the rotary dimmer 2x shortly to send an OFF signal. The LED on the dimmer flashes 2x red.

3. Pair a Trust Smart Home receiver

  • A Activate the learning mode of the receiver (Consult the receivers manual on how to put it into the learning mode).
  • B When the learning mode is active, give an ON signal by pressing the button on the rotary dimmer once to pair it to the receiver. The LED on the rotary dimmer flashes 1x green.

4. Dim Trust Smart Home dimmer

Dim Trust Smart Home dimmer

Give an ON signal to switch on the lamp

  • A Turn the rotary dial to the right to increase the light intensity of the lamp
  • B Turn the rotary dial to the left to decrease the light intensity of the lamp

Optional: Follow below steps if you want to use the rotary dimmer to dim an ALED lamp.

A Remove the battery from the dimmer for 5 seconds.
Place the battery back in the dimmer. (See step 1 “Insert / replace the battery”). B Give within 6 seconds after placing the battery an ON signal with the rotary dimmer and keep it pressed until the LED flashes 2x red (6 times).

To increase or decrease the brightness of an ALED lamp, turn the knob slowly to the right or left.

To return to the original settings, in step B keep pressing the rotary dial until the LED flashes 6x

5. Mount the rotary dimmer

Mount the rotary dimmer

  • A Mount the rotary dimmer with double-sided tape
    If you want to mount the rotary dimmer using the supplied double-sided tape, apply the double-sided tape to the back plate of the rotary dimmer.
    Place the rotary dimmer (with the LED on the top) at the desired location on a flat surface.

  • B Mount the rotary dimmer with screws
    If you want to mount the rotary dimmer using the supplied screws, first remove the back plate from the rotary dimmer (see chapter 1 step A ) and screw it tightly to the desired location.

**** When mounting, the arrow on the back plate must point upwards. Then click the rotary dimmer back on the back plate.

When mounting on a wall box, make sure it is placed at even height with the wall and that the back plate is hand tightened to prevent bending of the back plate.

Optional: Unpair a Trust Smart Home receiver

Optional: Unpair a Trust Smart Home receiver

Put the receiver in the learning mode (see the manual of the receiver for information on how to activate the learning mode).

When the receiver is in learning mode, send an OFF signal with the rotary dimmer. The LED on the rotary dimmer flashes 2x red.

Optional: Choose Dimming mode

Optional: Unpair a Trust Smart Home receiver

Note: Only for ACC-250-LD and ACM-250-LD: Switch to a different dimming mode for more dim steps. To switch to a different dimming mode, remove the back plate from the rotary dimmer. (See chapter 1 step A ). After this move the switch from position 1 to position 2. Place the back plate back on the dimmer. To dim other Trust Smart Home dimmers, the rotary dimmer must be set to position 1.

Safety Instructions

Product support: www.trust.com/71236. Warranty conditions: www.trust.com/warranty
To ensure safe handling of the device, follow the safety advice on: www.trust.com/safety
The Wireless range is strongly dependent on local conditions such as the presence of HR glass and reinforced concrete
Never use Trust Smart Home products for life-support systems. This product is not water-resistant. Do not attempt to repair this product. Wire colors may vary per country. Contact an electrician when in doubt about wiring. Never connect lights or equipment that exceed the maximum load of the receiver. Exercise caution when installing a receiver voltage may be present, even when a receiver is switched off. Maximum radio transmit power: -13.5 dBm. Radio transmission frequency range: 433,92 MHz

  • Disposal of packaging materials – Dispose of packaging materials which are no longer needed in accordance with applicable local regulations.
  • Disposal of the device – The adjacent symbol of a crossed-out wheelie bin means that this device is subject to Directive 2012/19/EU.
  • Disposal of batteries – Used batteries may not be disposed of in household waste. Only dispose of batteries when they are fully discharged. Dispose of batteries according to local regulations.
  • Trust Electronics Ltd. declares that item number 71236/71236-02 is in compliance with Directive Electromagnetic Compatibility Regulations 2016, Radio Equipment Regulations 2017. The full text of the declaration of conformity is available at the following internet address: www.trust.com/compliance
  • Trust International B.V. declares that item number 71236/71236-02 is in compliance with Directive 2014/53/EU – 2011/65/EU. The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

Declaration of Conformity

Trust International B.V. declares that this Trust Smart Home-product:
Model: AWRT-1000 wireless ROTARY button
Item number: 71236/71236-02
Intended use: Indoor
is in compliance with the essential requirements and other relevant provisions of the following directives:
ROHS 2 Directive (2011/65/EU)
RED Directive (2014/53/EU)
The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

TRUST SMART HOME
LAAN VAN BARCELONA 600
3317DD DORDRECHT
NEDERLAND
www.trust.com

Trust Electronics Ltd.,
Sopwith Dr, Weybridge, KT13 0NT, UK.
All brand names are registered trademarks of their respective owners.
Specifications are subject to change without prior notice. Made in China.

TECHNICAL SPECIFICATIONS

Codesystem Automatic
Channels 1
Size HxWxL: 80 x 80 x 25 mm
Power 3V lithium battery type CR2032 (included)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals