Trust 71151 AGST-8800 Outdoor Wireless Wall Switch User Manual

: June 9, 2024
: Trust

Table of Contents

Open wall switch
Pair the wall switch with a receiver
Mount the wall switch
Operating the wall switch
Replace Battery
Unpair wireless wall switch
Clear the memory of the receiver
Safety Instructions
Declaration of Conformity
TECHNICAL SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Trust 71151 AGST-8800 Outdoor Wireless Wall Switch

Open wall switch

Use a flathead screwdriver to remove the button first.
Then place the flat screwdriver in the recess of the frame and lift the screwdriver to unclip the frame from the back plate. Remove the rubber protector.

Pair the wall switch with a receiver

To operate a receiver first you must pair the wireless wall switch with the receiver. Put the receiver in learning mode (see the manual of the receiver to activate the learning mode).
Give an ON signal on the wall switch when the learning mode of the receiver is active. The receiver will give a confirmation that the pairing of the wall switch has been successful.

Mount the wall switch

A Use a flathead screwdriver to remove the button first.
B Then place the flat screwdriver in the recess of the frame and lift the screwdriver to unclip the frame from the back plate.
C Screw the back plate to a location with a flat surface (make sure the arrow on the back plate points up). After this, first place the rubber protection back on the backplate, then the frame and finally the push button.

Operating the wall switch

4a. Dimming

Press the ON button to turn on the receiver.
Press the ON button again to activate the dimmode. The light will slowly dim in a cycle.
Press for the third time the ON button to secure the desired dim level.
Press the OFF button to turn off the receiver.

4b. Switching On/Off

Press the ON button to turn on the receiver.
Press the OFF button to turn off the receiver.

4c. Open/Stop/Close

Press the ON button to open the blinds. Press the ON button again to stop the blinds.
Press the OFF button to close the blinds. Press the OFF button again to stop the blinds. Read the manual of the receiver to reverse the direction of the blinds.

4d. Activating wireless doorbell

Press the ON button to activate the melody of the wireless doorbell. For more information, see the manual of the receiver

Replace Battery

A Use a flathead screwdriver to remove the button first.
B Then place the flat screwdriver in the recess of the frame and lift the screwdriver to unclip the frame from the back plate. Remove the rubber protector.
C Remove the battery by inserting the flat screwdriver into the slot and sliding the battery out.
D When replacing the push button, make sure that the recess of the push button is on the same side as the recess of the frame

Insert a new CR2032 battery. Make sure the + side is facing up. The wireless wall switch is now ready for use again.

Unpair wireless wall switch

To unpair the wall switch put the receiver into learning mode. When the receiver is in learning mode give an OFF signal with the wall switch. The receiver will give a confirmation that the wall switch is unpaired.

Clear the memory of the receiver

Consult the manual of the receiver to erase its memory

Safety Instructions

Product support: www.trust.com/71151. Warranty conditions: www.trust.com/warranty To ensure safe handling of the device, follow the safety advice on: www.trust.com/safety The Wireless range is strongly dependent on local conditions such as the presence of HR glass and reinforced concrete Never use Trust Smart Home products for life-support systems. This product is water-resistant. Do not attempt to repair this product. Wire colors may vary per country. Contact an electrician when in doubt about wiring. Never connect lights or equipment that exceed the maximum load of the receiver. Exercise caution when installing a receiver voltage may be present, even when a receiver is switched off. Maximum radio transmit power: -10.25 dBm. Radio transmission frequency range: 433,92 MHz

Disposal of packaging materials – Dispose of packaging materials which are no longer needed in accordance with applicable local regulations.

Disposal of the device – The adjacent symbol of a crossed-out wheelie bin means that this device is subject to Directive 2012/19/EU.

Disposal of batteries – Used batteries may not be disposed of in household waste. Only dispose of batteries when they are fully discharged. Dispose of batteries according to local regulations.

Trust Electronics Ltd. declares that item number 71151/71151-02 is in compliance with Directive Electromagnetic Compatibility Regulations 2016, Radio Equipment Regulations 2017. The full text of the declaration of conformity is available at the following internet address: www.trust.com/compliance

Trust International B.V. declares that item number 71151/71151-02 is in compliance with Directive 2014/53/EU – 2011/65/ EU. The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance