Godox TimoLink TX Wireless DMX Transmitter Instruction Manual

Godox TimoLink TX Wireless DMX Transmitter Instruction Manual

Foreword

Thank you for purchasing!

TimoLink TX is a plug-and-play wireless DMX transmitter that supports Type-C power supply. It can transmit DMX signals to wireless DMX transmitter TimoLink RX via 2.4G wireless within 300 meters, this series together are often used in large stage shows, concerts, bars, etc.

Warning

Always keep this product dry. Do not use in rain or damp conditions.
Please reset the transmitter and receiver before connecting for better connection.
Do not leave or store the product if the ambient temperature reads over 45°C.
Do not disassemble. Should repairs become necessary, this product must be sent to our Company or an authorized mainte- nance center.

Name of Parts

TimoLink TX

1. Set Button
2. Signal Indicator
3. Power Indicator
4. Type-C Port
5. DMX Test Button
6. Antenna
7. 5-pin DMX Male Port
8. Reset Button

TimoLink RX

1. Signal Indicator
2. Power Indicator
3. Type-C Port
4. 5-pin DMX Female Port
5. Reset Button

Item List for TimoLink TX

Wireless DMX Transmitter *1

Instruction Manual *1

Charging Cable +1

Item List for TimoLink RX

Wireless DMX  Receiver *1

Charging Cable *1

Instruction Manual +1

**Separately Sold Accessories

** DMX Adapter DA5F3M

Operation Instruction

1. Insert the transmitter TimoLink TX into the female port of DMX512 controller, connect to DC power source with charging cable.

2. Insert the receiver TimoLink RX into the male port of the fixture, connect to DC power source with charging cable.

3. Short press the reset buttons of the transmitter TimoLink TX and receiver TimoLink RX to reset to them.

4. Short press the set button of transmitter TimoLink TX with the DMx test button offthe signal indicator flashes quickly means connecting with the receiver TimoLink RX, the signal indicator flashes slow down means connected, then the transmitter and the receiver will be constant on the same color.
   
   Note: When the transmitter is about to connect to multiple receivers, be sure to reset all receivers and connect them to power source, then short press the transmitters’ ‘set buttons to connect. Short press set button of the transmitter twice can switch the color of the signal indicator among 8 colors.

DMx Testing Functions

In order to ensure the DMX signal is successfully outputted, toggle the

DMX test button to ON after the above settings of . If there is DMX signal, the indicators of TX and RX will be constant on, and fixture will test the effects according to the established procedure, after which, please toggle the DMX test button to OFF.

Connection Illustration

Multi fixtures controlled by one controller

Multi fixtures controlled by one controller

Note: The DMX512 controller is sold separately, and the pictures are for reference only.

Technical Data

functions
DMX plug rotatable angle| 270°
Controlling Distance| Max. 300m(in an open and barrier-free environment)
Working Environment Temperature| -2045°C
Dimension| 141mm96mm26mm| 110mm53mm26mm
Net Weight| 89g| 80g

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

Warning

Operating frequency: 2412.99MHz — 2464.49MHz
Maximum EIRP Power: 5dBm

Declaration of Conformity

GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states.For more information of DoC, Please click this web link: https://www.godox.com/DOC/Godox_TimoLink_Series_DOC. pdf.

The device complies with RF specifications when the device used at Omm from your body.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safekeep it.
Thank you!

Address
Seller Information| Name
Contact Number
Address
Date of Sale
Note:

Note: This form shall be sealed by the seller.

Applicable Products

The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached, etc.) are not included in this warranty scope.

Warranty Period

The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions, You can also contact the Godox after-sale service call and we will offer you service, When applying for maintenance service, you should provide valid warranty card, If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is, involved in the maintenance scope, but that shall not be considered as our obligation,

Inapplicable Cases

‘The guarantee and service offered by this document are not applicable in the following cases: (1), The product or accessory has expired its warranty period; (2), Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, ete; (3). Breakage or damage caused by non- authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment; (4). The original identifying information of product or accessory is modified, altemated, or removed; (6). No valid warranty card; (6). Breakage or damage caused by using illegally authorized, nonstandard or non-public released software; (7). Breakage or damage caused by force majeure or accident; (8). Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility, The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope, The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope,

Maintenance and Service Support Information

The warranty period and service types of products are implemented according to the following Product Maintenance Information:

designated site
Other Items| Flash tube, modeling lamp, lamp body,lamp cover, Iockingdevice, package, etc.| No| Without warranty

Godox After-sale Service Call 0755-29609320-8062

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>