Godox WT40D Drive Light Instruction Manual

Godox WT40D Drive Light

Safety Instructions and Attentions

First of all, as the most basic principle:
This product is a professional lighting set equipment and should be used by professional lighting engineers or under the guidance of professionals.

Basic safety attentions must always be followed during use, as follows:

1. Before use, please read and understand these instructions and attentions.
2. Professional lighting is prohibited for children. When children are near, parents or accompanying persons must supervise closely to prevent children from personal injury due to collision with lamps or private use of lamps.
3. This lighting product is not ordinary lighting product and cannot be used for general lighting. Anyone who has suffered eye damage or has sensitive eyes should avoid using this product.
4. When the lamp is on, it must be used with care. Do not touch high-temperature parts, such as LED lamp beads, to avoid burns.
5. When the lamp is on, it is forbidden to look directly at the lamp beads under any circumstances. Strong light should be used under the guidance of professional lighting engineers. Avoid prolonged exposure to strong light under any circumstances. If eye discomfort, please turn off the lamp in time, suspend use, and see a doctor immediately.
6. If the lamp bead is damaged or deformed by heat, stop using this equipment, and contact the manufacturer, service agent or qualified maintenance personnel to replace the lamp bead in time to avoid accidents.
7. This product is only suitable for use in -10°C to +40°C operating environment .
8. Do not use damaged equipment or accessories, and wait for professional maintenance personnel to check and repair to confirm being normal before use.
9. During using, if the casing of this product is broken due to being dropped, squeezed or subjected to strong impact, please do not use it, so as to avoid electric shock injury due to contact with internal electronic components.
10. If an extension cord is required, please use an extension cord with a current rating greater than or equal to that of the equipment. If an extension cord is rated less than the equipment, overheating may result.
11. Some products have long power cords, please place the power cords properly and keep them in a safe place. Avoid contacting the power cord with overheating surfaces, avoid improper placement that could cause pulling damage, or trip on-site personnel. Please use the certified power cord from the original manufacturer. If the product is damaged by using a non-certified power cord, it will not be repaired by our factory.
12. Be sure to unplug equipment from the power outlet before cleaning and repairing. When not in use, do not pull the power cord to unplug the equipment. For normal power-off, please hold both ends of the plug of the equipment with your hands and pull the plug out of power outlet. This equipment needs to be connected to a grounded outlet. Do not disassemble the product without permission. If the product fails, it must be checked and repaired by authorized maintenance personnel.
13. Before storing, make sure that the equipment has cooled down completely. For storage, unplug the
14. power cord from the equipment. The equipment should be placed in the carrying case or in a ventilated dry place.
15. Do not place equipment near flammable and volatile solvents such as alcohol and gasoline.
16. Do not use accessories that are not recommended by our factory to avoid fire, electric shock or personal injury.
17. When cleaning, do not wipe it with a damp cloth, please use a dry cloth or a soft cloth to wipe the dirt of the equipment.
18. Please take off the protective cover before using.
19. This product complies with RoHS, CE and FCC certification, please refer to the relevant national standards for use and operation.
20. The safety instructions are formulated according to the strict testing of the factory, and the design and specifications of the equipment are subject to change without prior notice. For latest product information, please check the GODOX website and view latest electronic instruction.
21. Some products have built-in lithium batteries. Please u se specified chargers, and use them within a proper range of the specified voltage and temperature according to the correct operating instructions.
22. Some products are battery powered. Do not use any batteries, power sources or accessories not specified in the instructions for such products. Keep batteries and other accessories out of the reach of children and infants. In the instance that a child or infant swallows a battery or accessory, immediate emergency medical attention is required. If the battery leaks, becomes discolored, deformed, emits smoke, or emits an abnormal odor, remove it immediately. Be careful during removal to avoid burns. Continued use could result in fire, electric shock, or burns. Do not use any deformed or modified batteries. Do not disassemble or modify this product or battery. Do not heat or solder the battery. Keep the battery away from fire or water. Do not incorrectly insert the positive and negative ends of batteries, or mix old and new batteries or batteries of different types together.
23. One-year warranty period, accessories such as consumable batteries, adapters, power cords, etc. are not covered by this warranty.
24. If it is found that the equipment is repaired without authorization, the one-year warranty period will be cancelled and relevant fees will be charged for maintenance.
25. Machine failures caused by non-standard operation are not covered by the warranty. keep these Instructions!

Foreword

Thank you for purchasing!
Godox Dive Light series has a IP68 waters roof function of up to 40 meters, ultra-high output power, Bluetooth APP smart control. 13 realistic light i effects and adjustable brightness from 0% to 100%. This series can be widely used for filling light in diving, underwater photography, underwater recording, underwater light show and etc.

Main Features

• Smart brightness adjusting ability to auto magically enter high light mode under water
• Waterproof rate IP68, workable up to 40m underwater.
• Support Bluetooth APP remote control (only workable in above water mode).
• Battery level indication gives convenience and utility.
• Selectable mounting methods: 1/4″ screw or 1/4″ to 1· ball joint.
• 13 FX modes and freely adjustable brightness.
• WT25D and WT40D support fast charging through USB Type-C port.

Warning

• Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center
• Keep out of reach of children .
• Do not use the product in the presence of flammable gases, chemicals and other similar materials. In certain circumstance, please pay attention to the relevant warnings
• Built-in lithium battery, do not disassemble, impact. squeeze or put it into fire. If serious bulge occurs, please do not use
• Do not leave or store the product if the ambient temperature reads over 50°C.
• Please use the proper charger and follow the operation instruction.
• Make sure to seal the charging port with silicone lid and then close the cover before using under water. A Please wash it with clean water and put it in a dry and ventilated place after using in the sea.

Name of Parts

1. OLEO Panel
2. Power Switch
3. DIM Button
4. + Button
5. MOD/Bluetooth Button
6. FN Button
7. – Button
8. Type-C Charging Port (WT25D/WT40D)
9. DC Charging Port (WT60D)

1. FX Icon
2. Bluetooth
3. Underwater Highlight Mode
4. Battery Life (only displays in the main interface)
5. Battery Level
6. FX Mode
7. FX Level
8. DIM Adjust Ratio

Item List

joint 1
WT40D| Light bodyl, Type-C charging cable1, Portable ropel, 1/4″ to 1· ball joint 1
WT60D| Light bodyl, Adapterl, Power cablel, Portable rope1, 1/4″ to 1″ ball joint 1

Separately Sold Accessories

Light clamp WT-C01

Operation Instruction

1. Power Switch
   Long press the power switch for 1 second to power on or off the device. When the light is on in power on status, short press the power switch once to turn off the light, the DIM value is 0%, short press again to resume the previous DIM value.

2. Brightness Adjustment
   In the main interface, short press the+ button once can increase the DIM value by l unit, long press the+ button can increase the DIM value quickly. Short press the – button once can decrease the DIM value by 1 unit, long press the – button can decrease the DIM value quickly.

3. FX Mode
   Short press the MOD/Bluetooth button to switch to FX mode.
   FX Brightness Adjustment: In the FX mode interface, short press the DIM button once to make the DIM value blinks, then  short press the+ button once can increase the DIM value by  unit, long press the+ button can increase the DIM value quickly. Short press the -button once can decrease the DIM  value by 1 unit, long press the – button can decrease the DIM value quickly. Finally, short press the DIM button once can exit the brightness setting. It will automatically exit the brightness setting when the DIM value stops blinking after la seconds of idle use.FX Selection: In the FX mode interface, short press the FN button can switch FX type. Short press the FN button twice quickly can switch to the previous FX type. Short press the+ button or – button can adjust the FX level. FX Table of WT25D/WT40D/WT60D (7 3 kinds within 5 types)
   

4. Mode Description

5. Calibrating Function
   The calibrating function is helpful when there are abnormalities in switching between above water mode and underwater mode.
   Calibrating mode: Long press the MOD button and – button at the same time when the light is dry in above water mode to enter calibrating mode.
   When the “Calibrating» is displayed on the panel, it means calibration is in process.
   When the”✓” and “Done· is displayed on the panel, it means calibration is complete When the “x” and MF ailed” is displayed on the panel, it means calibration is failed.

6. Bluetooth Setting
   Long press the MOD/Bluetooth button to enter Bluetooth setting interface. Short press the FN button to choose Bluetooth switch (ON/OFF) or Bluetooth reset. If you choose Bluetooth switch, short press the+ button or – button to turn on or off the Bluetooth. If you choose Bluetooth reset, short press the
   + button or- button to reset the Bluetooth. When “Reset” is displayed on the panel, it means resetting, after which, it will return to Bluetooth setting interface automatically.
   Scan the following QR code to download “Godox Light” mobile APP (both Android and IOS systems are available).
   For specific operations, please refer to the “Help” manual of the mobile APP, which contains detailed instruction.
   Note: the APP can be used directly on the firstly installed device (smartphone or tablet).
   When changing to other mobile devices, the light shall be reset before normal usage of APP.

7. Abnormal Charging Alert
   When the icon appears on the display, there may be battery abnormality, charger abnormality or other abnormalities.

illuminance Data

WT25D

WT40D

WT60D

All the above tests are based on the condition of 100% brightness.

Technical Data

soonest
Battery life (100%brightness)| “‘1h {underwater) R<2h20min (above water)| ;:::1h20min (underwater) “”5h30min (above water)| :::2h (underwater) R:6h (abovewater)
Control Method| Bluetooth APP control
Bluetooth control distance| ::::c25m (only abovewater)
Working environment temperature| -10°C-40°C
Dimension| 57mm52mm250mm| 57mm52mm380mm| 57mm52mm640mm
Net Weight| 0.64kg| 1.08kg| 1.9kg

Warning

• Operating frequency: 2402MHz – 2480MHz
• WT25D Maximum EIRP Power: 6.65dBm
• WT40D Maximum EIRP Power: 6.7dBm
• WT60D Maximum EIRP Power: 5dBm

Declaration of Conformity
GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states.
For more information of DoC, Please click this web link:https://www.godox.com/D0C/Godox_WT25D_WT40D_WT60D_D0C.pdf.
The device complies with RF specifications when the device used at 0mm from your body.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!

Address
Seller Information| Name
Contact Number
Address
Date of Sale
Note

Note: This form shall be sealed by the seller

Applicable Products

The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached. etc.) are not included in this warranty scope.

Warranty Period I

The warranty period of products and accessories isimplemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time.And the purchase date is considered as the date registered onthe warranty card when buying the product.

How to Get the Maintenance Service

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the God ox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases

The guarantee and service offered by this document are not applicable in the following cases:

1. The product or accessory has expired its warranty period;
2. Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc;
3. Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment;
4. The original identifying information of product or accessory is modified, alternated, or removed;
5. No valid warranty card;
6. Breakage or damage caused by using illegally authorized, nonstandard or non-public released software;
7. Breakage or damage caused by force majeure or accident;
8. Breakage or damage that could not be attributed to the product itself.

Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility.
The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope.
The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information

The warranty period and service types of products are implemented according to the following Product Maintenance Information:

designated site
Other Items| Flash tube, power cord, sync cable. modeling lamp. lamp body, lamp cover, locking device, package, etc| No| Without warranty

Gcx:. lox After-sale Service Call +86-755-29609320(8062)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>