SIEMENS RDG110U Room Thermostat Instruction Manual

June 9, 2024
SIEMENS

SIEMENS RDG110U Room Thermostat Instruction Manual

SIEMENS RDG110U Room Thermostat Instruction Manual

Changing the room temperature

  • The room temperature setpoint can be adjusted with the rotary knob when Comfort mode is active
  • Turn the rotary knob clockwise (+) to increase, or counterclockwise (-) to decrease the current room temperature setpoint for Comfort mode

The setting range is from 5…40 °C (41 … 104 °F), unless limited by parameters P09 and P10 (for parameter settings, see reverse side).

Adjusting the fan speed

  • Press the fan mode button until the desired fan mode is reached
  • In Automatic mode , the fan speed is automatically selected by the thermostat depending on the setpoint and the actual room temperature. When the room temperature reaches the setpoint, the fan stops (factory setting) or runs at low speed (P15).
  • In Manual mode, the fan operates independently and always runs at the same speed: Low / medium / high

Note: If desired, you can change the fan mode selector option via P03: Manually only, or manually including Protection mode. Use P15 to set the fan speed in dead zone.

Selecting Comfort mode

  • Press the operating mode button until symbol that Comfort mode is selected appears, indicating
  • In Comfort mode, the thermostat maintains the setpoint which can be readjusted with the rotary knob

Selecting Protection mode

  • Press the operating mode button until symbol that Protection mode is selected appears, indicating
  • In Protection mode, the plant stops operating. If the room temperature falls below 8 °C, heating is switched on however to protect the room against frost

The setpoints for Protection mode can be changed by your HVAC installer if desired:

Changes made by installer:

Frost protection: ____ °C / °F

Heat protection: __°C / °F

Selecting Economy mode

In Economy mode, the room temperature is maintained at a lower or higher setpoint, thus saving energy and money.

  • When selecting Economy, make sure that parameter P02 is set to 2
  • Press the operating mode button until symbol appears
  • You can change the preselected setpoint by adjusting parameters P11 and P12 (for parameter settings, see reverse side)

Important: The setpoint for Economy can be set to OFF. This means that the thermostat is deactivated! Risk of frost, i.e. no protective heating or cooling function is provided!
Energy saving tips without sacrificing comfort: · Air out rooms for short periods of time only, but properly, with the windows wide open · Never allow the room temperature to exceed 21 °C (70 °F) through heating, and to fall below 25.5 °C (78 °F) through cooling

Button lock

  • · To lock or unlock the buttons manually, press and hold the fan mode button for 3 seconds. The buttons are locked or unlocked in this manner if P14 is set to 2
  • If P14 is set to 1, the thermostat automatically locks the buttons 10 seconds after the last adjustment

Temporary timer for extended presence or absence

The Comfort and Economy modes can be temporarily extended by 0.5 to 9.5 hours using the temporary timer.

SIEMENS RDG110U Room Thermostat Instruction Manual - Temporary timer for
extended presence or absence

  1. To set the temporary timer, press and hold the operating mode button for maximum 3 seconds. While holding the button, turn the rotary knob clockwise or counterclockwise as required. a) Turn the rotary knob clockwise to extend Comfort mode. Display: 0….+9:30 b) Turn the rotary knob counterclockwise to extend Economy mode. Display: 0….-9:30
  2. Release the operating mode button and the mode is temporarily changed, indicated by .
    After the temporary timer has elapsed, the thermostat will resume operation in the operating mode that was active before: Extended Comfort mode
    New operating mode = Economy Extended Economy mode
    New operating mode = Comfort
  • If Economy cannot be selected via the operating mode button (P022), Protection mode will be used for extended absence instead!
  • The temporary timer function is aborted whenever a new setting is made.

Note: Extended Comfort mode is also possible when an external contact such as a keycard switch or central time clock is active To enable this function, the time for the extended period must be set via parameter P68.

Changing from heating to cooling mode

  • Depending on the type of plant, the changeover from heating to cooling (or vice versa) is made either automatically by a changeover sensor or a remote changeover switch, or manually by pressing the operating mode button (see parameter P01)
  • To select cooling or heating manually (P01=2), press the operating mode button until the desired mode appears
  • With automatic changeover or continuous heating / cooling, symbols / indicate that the system currently operates in heating or cooling mode
  • With manual changeover, symbol appears, indicating that the system currently operates in heating or cooling mode

Control parameters

SIEMENS RDG110U Room Thermostat Instruction Manual - Control
parametersIf you want to change control parameters, proceed as follows:

  1. Press both buttons simultaneously for at least 3 seconds.
  2. Release them and, within 2 seconds, press the right button again for 3 seconds. The display shows P01.
  3. Select the required parameter by turning the rotary knob.
  4. Press button (OK). The current value of the selected parameter starts blinking and can be changed by turning the rotary knob.
  5. Press button (OK) to confirm the adjusted value, or (Esc) to cancel the change.
    If you wish to adjust additional parameters, repeat steps 3 through 5, or press (Esc) to leave the parameter setting mode.

Parameter list

SIEMENS RDG110U Room Thermostat Instruction Manual - Parameter
list

  • Degree Fahrenheit parameter selections are only applicable to RDG110U version

The control parameters displayed depend on the DIP switch settings made

Siemens Switzerland Ltd Subject to change B3181.1en 2014-10-20

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals