CHAPIN 16200 2-Gallon Home and Garden Sprayer User Manual
- June 9, 2024
- CHAPIN
Table of Contents
16200 2-Gallon Home and Garden Sprayer
User Manual
16200 2-Gallon Home and Garden Sprayer
WARNING
WARNING: Improper use or failure to follow instructions can result in
explosive failure causing serious eye or other injury. For safe use of this
product you must read and follow all instructions. Do not leave a pressurized
sprayer in the hot sun. Heat can cause pressure build-up resulting in possible
explosion. Do not store or leave solution in tank after use. Always wear
goggles, gloves, long sleeve shirt, long pants and full foot protection when
spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump
to prevent ejecting pump assembly and/or solution from striking and injuring
you. Never pressurize sprayer by any means other than the original pump. Do
not attempt to modify this sprayer. Replace parts only with manufacturer’s
original parts. Never spray flammable, caustic, acidic, chlorine, bleach or
other corrosive solutions or heat, pressure, or gas producing chemicals.
Always read and follow chemical manufacturer’s instructions before use with
this sprayer as some chemicals may be hazardous when used with this sprayer.
Sk-1154-1
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or
www.chapinmfg.com
Hose to Tank
- Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1A).
- Firmly insert the outlet tube portion into the tank adapter (Fig. 1B) leaving no gap between the tank adapter and outlet tube adapter. Firmly tighten the retaining nut to the tank adapter (Fig. 1C).
Extension Wand to Shut-off
Loosen retaining nut from shut-off (2A). Insert extension wand into end of shut-off until you no longer see the line marked on the end of the wand. Tighten retaining nut (2C).
Pre-Use Check
- Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
- Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose before using. Replace with original manufacturer’s parts only.
- Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
- Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and inspect for leaks).
- Do: Direct shut-off away from you and open to make sure discharge is not clogged.
- Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling, Pressurizing and Spraying Instructions.
- Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of these conditions are found, replace affected part with original manufacturer’s part before using.
Filling
- Do: Turn pump handle counterclockwise and remove pump
- Do : Prepare spray solution following all directions and safety warnings on chemical label.
- Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
- Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
Pressurizing and Spraying
Do: Turn handle clockwise to tighten. Push handle down, turn 1/4 turn counterclockwise to release.
Do: Pump until you feel resistance.
Do: Push handle, down, turn 1/4 turn clockwise to lock. Begin spraying. Re-pump sprayer as required to maintain spray force.
Do: Turn end of nozzle to adjust spray pattern.
To Release Pressure
Sprayers with no pressure release valve
Do: With pump facing away, turn locked handle counterclockwise until air
begins to escape. Stop turning handle when you hear air escaping.
Do: Point pump away until all air has escaped.
Care, Storage and Maintenance
- Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed with water after each use.
- Do: Open shut-off and allow water to run through discharge assembly.
- Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
- Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
- Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
Fatigue-Free Spraying
To Lock
For constant spraying, push down on shut-off handle and slide forward.
To Un-Lock
To release, press down and slide handle back.
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458
www.chapinmfg.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>