RYOBI RCD12011L Cordless Drill Driver User Manual

RYOBI RCD12011L Cordless Drill Driver

INSTALLATION INSTRUCTION

BATTERY INSTALLATION

Important: It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.

Safety, performance, and dependability have been given top priority in the design of your drill driver.

INTENDED USE

• The drill driver is intended to be used only by adults who have read and understood the instructions and warnings in this manual, and can be considered responsible for their actions.
• The product can be used for drilling into various materials, including wood, metal, and plastics using a drill bit having a diameter of less than 10 mm. The product can be used to drive and remove screws and bolts using an appropriate bit.
• Do not use the product in any way other than those stated for intended use.

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury.

Save all warnings and instructions for future reference.

DRILL DRIVER SAFETY WARNINGS

• Wear ear protectors when drilling. Exposure to noise can cause hearing loss.

• Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

• Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. When not in use, all tools should be disconnected from power source.

• The dust produced when using the product may pose a health hazard. Do not inhale the dust. Wear a suitable dust mask.
  Do not operate on materials (e.g., asbestos) that present a health hazard.

• Switch off the product immediately if the bit stalls. Do not switch on the product again while the bit is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the bit stalled and rectify this, paying heed to the safety instructions.

• The possible causes may be:

  • it is tilted in the workpiece
  • it has pierced the workpiece
  • the product is overloaded

• Sawdust and splinters must not be removed while the product is running.

• When working in walls, ceilings, or floors, avoid electrical cables and gas or water pipes.

• Secure your workpiece with a clamping device.

RESIDUAL RISKS: Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:

• Risk of electrocution if electric cables are drilled into. Always grasp the product by designated handles; do not touch the drill bits.
• Injury caused by vibration. Hold the product by designated handles and limit exposure to vibration. See “Risk Reduction”.

RISK REDUCTION

It has been reported that vibrations from hand-held tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness and blanching of the fi ngers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. These are measures that can be taken by the operator to possibly reduce the effects of vibration:

• Keep your body warm in cold weather. When operating the unit wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
• After each period of operation, exercise to increase blood circulation.
• Take frequent work breaks. Limit the amount of exposure per day.

If you experience any of the symptoms of this condition, immediately discontinue use and see your doctor about these symptoms.

WARNING: Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

MAINTENANCE

• When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.
• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
• Do not attempt to modify this tool or create accessories not recommended for use with this tool.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling.

LED INDICATOR

BATTERY OVERLOAD PROTECTION

This tool is designed to protect the battery from overloading. When overloading is detected, the tool will automatically switch off. To resume operation, switch the tool off and on again. If the tool fails to operate, it means battery pack is discharged and should be recharged in a compatible charger.

SYMBOL

• Safety alert
• EurAsian Conformity Mark
• CE conformity
• Ukrainian mark of conformity
• Please read the instructions carefully before starting the machine.
• Recycle
• Torque, maximum
• Torque, minimum
• Speed, minimum
• Speed, maximum

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice

Product specifications

Drill Driver
Model
Voltage
Chuck
Switch (Variable speed)
No load speed (drill mode):

Clutch (Positions)

Maximum torque
Maximum spade bit

Weight – excluding battery pack

Product specifications

Measured sound values determined according to EN 60745:

A-weighted sound pressure level

Uncertainty K

A-weighted sound power level
Uncertainty K

Wear ear protectors.

Weighted root mean

The vibration total values (triax vector sum) determined according to EN 60745

Drilling into metal, vibration emission value

Uncertainty K
Screw driving without impact, vibration emission value
Uncertainty K
Battery and charger

Compatible battery pack (not included)

Compatible charger (not included)

WARNING: The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.

1. The guarantee period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
2. There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data which are required to enter online and they have to accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty. Your statutory rights remain unaffected.
3. The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to:
   •  any damage to the product that is the result of improper maintenance
   • any product that has been altered or modified
   • any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
   • any damage caused by non-observance of the instruction manual
   • any non CE product
   • any product which has been attempted to be repaired by an non-qualified professional or without prior authorization by Techtronic Industries
   • any product connected to improper power supply (amps, voltage, frequency)
   • any damage caused by external influences (chemical, physical, shocks) or foreign substances
   • normal wear and tear of spare parts
   • inappropriate use, overloading of the tool
   • use of non-approved accessories or parts
   • carburettor after 6 months, carburettor adjustments after 6 months
   • power tool accessories provided with tool or purchased separately. Such exclusions include but is not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide
   • components (parts and accessories) subject to natural wear and tear, including but not limited to carbon brushes, chuck, power cord, auxiliary handle, sanding plate, dust bag, dust exhaust tube
4. For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
5. A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will have to be paid by the sender.
6. This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRE
To find an authorised service centre near you, visit http://uk.ryobitools.eu/header/service-and-support/service-agents.

EC DECLARATION OF CONFORMITY

• Techtronic Industries GmbH
• Max-Eyth-Straße 10, 71364 Winnenden, Germany

Herewith we declare that the product

• Drill Driver
• Brand: Ryobi
• Model number: RCD1201
• Serial number range: 44444901000001 – 44444901999999
  is in conformity with the following European Directives and harmonised standards
  2011/65/EU, 2006/42/EC, 2004/108/EC (until 19 April 2016),
  2014/30/EU (from 20 April 2016),
  EN55014-1:2006+A1:2009+A2:2011, EN55014-2:1997 + A1:2001 + A2:2008,
  EN60745-1: 2009+A11:2010, EN 60745-2-1:2010, EN60745-2-2:2010

RoHS documentation is compiled according to EN 50581:2012 Andrew John Eyre (BEng, CEng, MIET) Vice President, Regulatory & Safety Winnenden, Jun. 23, 2015 Authorised to compile the technical file: Alexander Krug, Managing DirectorTechtronic Industries GmbH Max-Eyth-Straße 10, 71364 Winnenden, Germany

https://tm.by
MHTepHeT-Mara3nH TM.by

References

• Ryobi Tools
• Ryobi Tools
• SAV Ryobi France: Pièces détachées et réparations Ryobi : le service client Ryobi
• Ryobi Norge | Elverktøy, ONE+, Hagemaskiner, 36V
• Ryobi Tools
• Ryobi Tools
• Ryobi Tools UK
• Ryobi Danmark | Elværktøj ONE+, Havemaskiner, 36V
• Ryobi Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>