hama 00184160 Bluetooth Headphones Instruction Manual

hama 00184160 Bluetooth Headphones

Thank you for choosing a Hama product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

Controls and displays

1. + button
2. – button
3. NC button
4. Multi-function button (MFB)
5. Status LED
6. Audio input (3.5 mm)
7. USB-C connection
8. Microphone

Explanation of warning symbols and notes

Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note
This symbol is used to indicate additional information or important notes.

Package contents

• 1x “Spirit Focused” Bluetooth® Over-Ear Stereo Headphones
• 1x USB-C charging cable
• 1x quick guide
• 1x warning and safety instructions
• 1x bag

Safety Instructions

• The product is intended for private, non-commercial use only.
• Use the product only for the intended purpose.
• Children should be supervised to ensure that they do not play with the product.
• Do not use the product in areas in which electronic products are not permitted.
• Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
• Do not open the device or continue to operate it if it becomes damaged.
• Do not bend or crush the cable.
• Do not drop the product and do not expose it to any major shocks.
• Dispose of packaging material immediately in accordance with the locally applicable regulations.
• Do not modify the product in any way. Doing so voids the warranty.
• Protect the product from dirt, moisture, and overheating, and use it in dry environments only.
• Do not use the product in the immediate vicinity of heaters, other heat sources, or in direct sunlight.
• Only use the article under moderate climatic conditions.
• As with all electrical products, this device should be kept out of the reach of children.
• Do not operate the product outside the power limits given in the specifications.
• Do not use the product in a damp environment and avoid splashing water
• While driving a car or using sports equipment, do not allow yourself to be distracted by your product, and keep an eye on the traffic situation and your surroundings.
• The battery is permanently installed and cannot be removed; dispose of the product as a whole in accordance with the statutory regulations.
• Do not incinerate the battery or the product.
• Do not tamper with or damage/heat/disassemble the batteries/rechargeable batteries.
• Do not use the product during the charging process!

Warning – rechargeable battery

• Only use suitable charging devices or USB ports to charge the product.
• Do not use defective chargers or USB ports and do not attempt to repair them.
• Do not overcharge the product or allow the battery to completely discharge.
• Avoid storing, charging, and using in extreme temperatures and at extremely low atmospheric pressures (such as at high altitudes).
• When stored over a long period of time, batteries should be charged regularly (at least every three months).

Warning – magnets

• This product generates magnetic fields. Individuals with cardiac pacemakers should consult a doctor before using this product as it may affect the pacemaker’s proper function.
• Do not store bank or similar cards with magnetic strips near the charging box or earphones. The data on the cards could be damaged or completely deleted.

Warning – high volume

• High sound pressure!
• There is a risk of hearing damage.
• To prevent any loss of hearing, avoid listening at loud volumes for prolonged periods.
• Always keep the volume at a reasonable level. Loud volumes can damage hearing – even over short periods.
• Using this product limits your perception of ambient noise. You should therefore not operate vehicles or machines while using them.

Switching on/off

• ON
  Press the MFB button (4) for around 5 seconds until a signal tone is heard and the LED (5) flashes blue.

• OFF
  To switch off, press the MFB button (4) for around 5 seconds until a signal tone is heard and the LED (5) flashes Red and then goes out.

Note – Automatic switch-off of the headphones
The headphones are equipped with an automatic switch-off mechanism. If there is no connection to your device within 5 minutes, they switch off automatically.

Charging

Fully charge the headphones once before using them for the first time.

1. Switch off the headphones and connect them
   Ensure that the headphones are switched off before charging them. Connect the USB charging cable included to the charging socket (7). Connect the free plug on the USB-C charging cable to a suitable USB charger. To do this, consult the operating instructions for the USB charger you are using.

2. Charging process for the headphones
   The LED (5) lights up solid red during the charging process. Once fully charged, the LED (5) lights up solid blue.
   It can take up to 1.5 hours for the battery to be fully charged.

3. Battery capacity
   When the headphone battery capacity is low (<10%), the LED (5) flashes red and a signal tone is heard.

Bluetooth Pairing

Note – pairing

• Ensure that the Bluetooth®-enabled device is switched on and that the Bluetooth® function is activated.
• Please refer to the operating instructions of your device for more information.

The headphones and the device should not be more than 1 meter apart. The shorter the distance, the better. Switch the headphones on using the MFB button (4).

1. Check the status of the status LED (5) and the announcements
   If the LED (5) is flashing alternately:
   Headphones searching for a Bluetooth® connection.
   If the LED (5) is flashing:
   The headphones are already paired with a Bluetooth® device.

2. Search using your device for the headphones (only required on the first connection)
   Open the Bluetooth® settings on your device and wait until the list of found Bluetooth® devices shows Hama Spirit Focused.
   Select Hama Spirit Focused and wait until the headphones are shown as connected in your device’s Bluetooth® settings.
   Note – Bluetooth® password
   Some devices require a password in order to connect to another Bluetooth® device.

   • If your device requests a password to connect to the headphones, enter 0000.

3. Multi-point technology
   These headphones can connect to two Bluetooth®-enabled devices simultaneously (multi-point).

   • First, connect the first device to the headphones.
   • Then deactivate the Bluetooth® function on this device.
   • Then connect the second device to the headphones.
   • Activate the Bluetooth® function on the first device again. The headphones then connect to this device too.

4. Disconnecting the Bluetooth® connection
   Disconnect the headphones via your device’s Bluetooth® settings.

Control elements

Note

• Please be aware that your terminal device must support some functions if they are to be used.
• Please refer to the operating instructions of your device for more information.

Voice assistant function
Press and hold the MFB button (4) for around 2 seconds to initiate communication with your Siri or Google Assistant. As soon as you hear a signal tone, your voice assistant is ready to assist you.

Note – Siri
Siri is only available on suitable devices running iOS 5 (iPhone 4s or later) or higher.

Note – Google Assistant

• The Google Assistant is only available on suitable devices running Android 5.0 or higher with Google Play Services, >1.5 GB of free memory and a minimum screen resolution of 720P.
• The Google Assistant App must be available on your device and be set as the default voice assistant.

ANC function
The headphones are equipped with an Active Noise Cancelling (ANC) function to reduce unwanted ambient noise. If ANC is activated, noise can be reduced by up to -20 dB. ANC can also be activated when the headphones are switched off.

• Press and hold the NC button (3) for approx. 1 second to switch on ANC and the LED light turns solid green. Press and hold the NC button (3) again for around 1 second to switch ANC off. The LED goes out.

Hands-free function
It is possible to use the earphones as a hands-free facility for your mobile phone.

1. Make a call
   Dial the number directly via your device to make a call.

2. Accept a call
   Press the MFB button (4) to accept an incoming call.

3. Reject a call
   Press and hold the MFB key (4) for around 2 seconds or use your device to reject an incoming call.

4. End a call
   During the call, press the MFB button (4) once to end the call.

5. Last number redial
   Press the MFB key (4) twice to redial the last number.

Note
The “Last number redial” function is only available for the device which was paired first in a multi-pairing situation.

Audio playback

Note
Please note that this function is only possible when a Bluetooth® connection is active.

1. Start playback on your device.

2. Play/Pause
   Press the MFB button (4) once to pause or start audio playback.

3. Next track
   Press and hold the + key (1) for around 2 seconds to skip to the next track.

4. Previous track
   Press and hold the – key (2) for around 2 seconds to skip to the previous track.

Volume control

1. Increase volume
   Press the + button (1) once to increase the volume. Once the maximum volume is reached, a signal tone is heard.

2. Reduce volume
   Press the – key (2) once to reduce the volume. Once the minimum volume is reached, a signal tone is heard.

Audio playback via an audio cable
(not included in the package contents) In addition to the connection via Bluetooth®, you can also connect these headphones using an AUX cable. To do this, plug one end into the device and the other end into the audio input (6). When the audio cable is inserted, the Bluetooth® connection is automatically disconnected. The headphones now function like cabled headphones.

Technical data

Bluetooth ® **headphones**

Impedance headphones/microphone| 32 Ω / < 2 .2 kΩ
Frequency headphones/microphone| 20 Hz – 18 kHz/100 Hz – 10 kHz
Sensitivity Headphones/microphone| 100 dB / -42 dB
Range| <10 m
Bluetooth ® **technology| v5 .0 + EDR
Profiles| A2DP, AVRCP, HFP
Transmission frequency| 2 .4 – 2 .48 GHz
Battery| Li-Po 3 .7 V
Min. capacity| 380 mAh
Current consumption| max. 5V  380 mA
Total weight| 215g
Standby** ***| ~ 365 d
Charging time| ~1 .5 h
ANC| -20 dB +/-2 dB
Music/talk   time (ANC on)| ~15 h
Music/talk   time (ANC off)**| ~23 h

Once fully charged

Care and maintenance

Only clean this product using a lint-free, slightly damp cloth, and do not use any harsh cleaners.

Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product, or failure to observe the operating instructions and/or safety notes.

Service And Support

Please contact Hama Product Consulting if you have any questions about this product.

• Hotline: +49 9091 502-0 (German/English)
• Further support information can be found here: www.hama.com.

Declaration of conformity

Hama GmbH & Co KG hereby declares that the radio equipment type [00184160] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address:
www.hama.com -> 00184160 -> Downloads.

• Frequency band(s) 2402 MHz – 2480 MHz
• Maximum radio-frequency power transmitted 2.5 mW E.I.R.P.

References

• hama.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>