RYOBI RLT183225F Cordless Grass Trimmer User Manual

: June 9, 2024
: RYOBI

Table of Contents

RYOBI RLT183225F Cordless Grass Trimmer
INTENDED USE
GENERAL SAFETY WARNINGS
LAWN TRIMMER /EDGE TRIMMER SAFETY
ADDITIONAL BATTERY SAFETY WARNINGS
TRANSPORTATION AND STORAGE
MAINTENANCE
RESIDUAL RISK
RISK REDUCTION
KNOW YOUR PRODUCT
SYMBOLS ON THE PRODUCT
INSTALLATION
Product Specifications
Battery and Charger
WARRANTY APPLICATION CONDITIONS
DECLARATION OF CONFORMITY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RYOBI RLT183225F Cordless Grass Trimmer

Important!
It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.

Subject to technical modification
Safety, performance, and dependability have been given top priority in the design of your cordless lawn trimmer/edge trimmer.

INTENDED USE

The cordless lawn trimmer/edge trimmer is intended to be used only by adults who have read and understood the instructions and warnings in this manual and can be considered responsible for their actions.
The product is only intended for use outdoors in a well-ventilated area. For safety reasons, the product must be adequately controlled by using two-handed operation.
When fi tted with the lawn trimmer head (and appropriate guard), the product is intended for cutting long grass, pulpy weed, and similar vegetation at or about ground level. The cutting plane should be approximately parallel to the ground surface when trimming and approximately vertical when edging.
The product should not be used to cut or trim hedges, bushes, or other vegetation where the cutting plane is not parallel to the ground surface.
Do not use the product for any other purpose.

GENERAL SAFETY WARNINGS

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury.
WARNING
When using the product, the safety rules must be followed. For your own safety and that of bystanders, please read these instructions before operating the product. Please keep the instruction safe for later use.
WARNING
This product is not intended to be used by children or persons with reduced physical, mental, or sensory capabilities. Children should be adequately supervised to ensure they do not play with the product.
WARNING
Some regions have regulations that restrict the use of the product. Check with your local authority for advice.

TRAINING

Read the instructions carefully. Be familiar with all controls and the proper use of the product.
Never allow children or people unfamiliar with these instructions to use the product. Local regulations may restrict the age of the operator.
Keep bystanders, children, and pets 15 m away from the area of operation. Stop the product if anyone enters the area.
Never use the product when you are tired, ill, or under the influence of alcohol, drugs, or medicine.
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property.

PREPARATION

Wear full eye and hearing protection while operating the product. If working in an area where there is a risk of falling objects, head protection must be worn.
Hearing protection may restrict the operator’s ability to hear warning sounds. Pay particular attention to potential hazards around and inside the working area.
Wear long trousers, boots, and gloves. Do not wear loose fitting clothing, short trousers, jewellery of any kind, or use with bare feet.
Secure long hair so it is above shoulder level to prevent entanglement in moving parts.
Before use and after any impact, check that there are no damaged parts. A defective switch or any part that is damaged or worn should be properly repaired or replaced by an authorised service centre.
Make sure the cutting attachment is properly installed and securely fastened.
Never operate the product unless all guards, deflectors, and handles are properly and securely attached. Consider the environment in which you are working. Keep the working area free from wires, sticks, stones, and debris which if struck by the cutter can become thrown objects.

BATTERY TOOL USE AND CARE

Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

LAWN TRIMMER /EDGE TRIMMER SAFETY

WARNINGS

Never allow children, persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge or people unfamiliar with these instructions to use the product.
Use the product in daylight or good with artificial light.
Avoid using on wet grass.
Keep proper footing and balance at all times and be sure of proper footing on slopes.
Do not walk backward when using the product.
Walk, never run.
Keep the head attachment below waist level.
Never use the product with damaged guards or without guards in place.
Do not fit a metal replacement line.
Keep hands and feet away from the cutting means at all times, especially when switching on the motor.
Beware, the cutting elements continue to rotate after the motor is switched off.
Beware of objects thrown by the cutting means. Clear debris like small stones, gravel, and other foreign objects from the work area before starting operation. Wires or string may become entangled with the cutting means.
Switch off and remove the battery pack before:
- servicing
- leaving the product unattended
- cleaning your product
- changing accessories
- checking for any damage after hitting an object
- checking for any damage if the product starts to vibrate abnormally
- performing maintenance
Wear full eye and hearing protection while using the product. If working in an area where there is a risk of falling objects, head protection must be worn.
Hearing protection may restrict the operator’s ability to hear warning sounds. Pay particular attention to potential hazards around and inside the working area.
Wear long trousers, boots, and gloves. Do not wear loose-fitting clothing, short trousers, jewelry of any kind, or use with bare feet.
Secure long hair so it is above shoulder level to prevent entanglement in moving parts.
The small blade fitted to the safety guard is designed to trim the new extended line to the correct length for safe and optimum performance. It is very sharp, do not touch it, particularly when cleaning the product.
Always ensure that ventilation openings are kept clear of debris.
Before use and after any impact, check that there are no damaged parts. A defective switch or any part that is damaged should be properly repaired or replaced by an authorised service centre.
Make sure the cutting head attachment is properly installed and securely fastened.
Make sure all guards, deflectors, and handles are properly and securely attached.
Do not modify the product in any way, this may increase the risk of injury to yourself or others.
Use only the manufacturer’s replacement cutting line. Do not use any other cutting attachment.
Immediately switch off and remove the battery pack in the event of accident or breakdown. Do not operate the product again until it has been fully checked by an authorised service centre.

ADDITIONAL BATTERY SAFETY WARNINGS

WARNING
To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
WARNING
Ensure that the line cut-off blade in guard is properly positioned and secured before each use.

TRANSPORTATION AND STORAGE

Stop the product, remove the battery pack, and allow it to cool down before storing or transporting.
Clean all foreign material from the product.
Do not store or transport the product with batteries fitted, remove and secure separately. Store the product in a cool, dry, and well-ventilated place that is inaccessible to children. Keep away from corrosive agents, such as garden chemicals and de-icing salts. Do not store outdoors.
For transportation in vehicles, secure the product against movement or falling to prevent injury to persons or damage to the product.

TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and regulations.
Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

MAINTENANCE

WARNING
Use only original manufacturer’s replacement parts, accessories, and attachments. Failure to do so can cause possible injury, contribute to poor performance, and may void your warranty.

WARNING
Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service, we suggest you bring the product to your nearest authorized service center for repair. When servicing, use only identical replacement parts.

Switch off and remove the battery the pack before conducting any maintenance or cleaning work.
You may make adjustments and repairs described in this manual. For other repairs, contact the authorised service agent.
For replacement line, use only nylon filament line of the diameter described in the specification table of this manual
After extending new cutter line, always return the product to its normal operating position before starting. After each use, clean the product with a soft dry cloth. Any part that is damaged should be properly repaired or replaced by an authorised service centre.
Check all nuts, bolts, and screws at frequent intervals for proper tightness to ensure the product is in safe working condition. Any part that is damaged should be properly repaired or replaced by an authorised service centre.
Bring the product to an authorised service centre to replace damaged or unreadable labels.

RESIDUAL RISK

Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:

Injury caused by vibration
Hold the product by designated handles and restrict working time and exposure.
Injury caused by exposure to noise
Wear hearing protection and limit exposure.
Injury caused by flying debris.
Wear eye protection at all times.

RISK REDUCTION

It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome. Symptoms may include tingling, numbness and blanching of the fi ngers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:

Keep your body warm in cold weather. When operating the product, wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
After each period of operation, exercise to increase blood circulation.
Take frequent work breaks. Limit the amount of exposure per day.
If you experience any of the symptoms of this condition, immediately discontinue use and see your physician.

WARNING
Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

KNOW YOUR PRODUCT

Parts RYOBI RLT183225F Cordless Grass Trimmer-fig2

Rear handle
Trigger
Flailing blade accessory
Telescoping collar
Charger
Battery latch button
Battery pack
Pivoting button
Spool cover
Spool
Eyelet
Cutting line
Cut-off blade
Safety guard
Edging button
Lower shaft
Upper shaft
Handle adjustment knob
Front handle
Lock-out trigger

SYMBOLS ON THE PRODUCT

Read and understand all instructions before operating the product, follow all warnings and safety instructions.
Wear eye protection
Wear ear protection
Wear non-slip safety footwear when using the product.
Do not use metal blade(s) on the product.
Do not expose to rain or damp condition.
Beware of thrown or flying objects. Keep all bystanders, especially children and pets, at least 15 m away from the operating area.
Keep hands away from cut-off blade
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Conforms to all regulatory standards in the country in the EU where the product is purchased.
EurAsian Conformity Mark
Ukrainian mark of conformity
Guaranteed sound power level

The following signal words and meanings are intended to explain the levels of risk associated with the product:

DANGER
Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury
CAUTION
(Without Safety Alert Symbol) Indicates a situation that may result in property damage.

SYMBOLS IN THIS MANUAL

Parts or accessories sold separately
Note
Warning

INSTALLATION

RYOBI RLT183225F Cordless Grass Trimmer-fig3

Product Specifications

RYOBI RLT183225F Cordless Grass Trimmer-fig19

Battery and Charger

WARNING

The declared vibration value has been measured with a standard test method and may be used to compare one tool with another.
The declared vibration value may be used in a preliminary assessment of exposure.
The vibration emission during actual use of power tool can differ from the declared total value depending on the ways in which the tool is used.
Identify safety measures to protect yourself based on an estimation of exposure in the actual conditions of use, taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time.

WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

The warranty period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.
There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newly-acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
- any damage to the product that is the result of improper or lack of maintenance
- any product that has been altered or modified
- any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
- any damage caused by non-observance of the instruction manual
- any product not displaying the CE approval mark on the rating plate
- any product that has been attempted to be repaired by a non-authorised warranty service centre or without prior authorisation by Techtronic Industries
- any product connected to improper power supply (amps, voltage, frequency)
- any product used with inappropriate fuel mixture (fuel, oil, ratio of oil/ fuel mixture)
- any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
- normal wear and tear spare parts
- inappropriate use, overloading of the tool
- use of non-approved accessories or parts
- Accessories provided with the tool or purchased separately including but not limited to blades, saw chains, cutting lines, etc.
- Any periodic adjustments to or maintenance cleaning of carburettors
- Components (parts and accessories) subject to natural wear and tear, including but not limited to bump knobs, drive belts, clutch, blades of hedge trimmers or lawn mowers, harness, cable throttle, carbon brushes, power cord, tines, felt washers, hitch pins, blower fans, blower and vacuum tubes, vacuum bag and straps, guide bars, saw chains, hoses, connector fittings, spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines, spark plugs, air filters, gas filters, mulching blades, etc.
For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
5. A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected.
6. This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.