RYOBI R18MT3 18V ONE+ Multi Tool User Manual

: June 9, 2024
: RYOBI

RYOBI R18MT3 18V ONE+ Multi Tool

Important!
It is essential that you read the instructions in this manual before assembling, maintaining, and operating the product.

Subject to technical modification

Safety, performance, and dependability have been given top priority in the design of your cordless line trimmer and brushcutter.

INTENDED USE

The multi-tool is intended to be used only by adults who have read and understood the instructions and warnings in this manual and can be considered responsible for their actions.

The multi-tool is intended to be used:

for sanding and finishing metal, wood, plastics, or similar materials using the sanding pad with the shaped abrasive sheets provided
for scraping and plunge-cutting into non-ferrous metal, wood, plastics, plasterboard, etc. using the provided metallic cutting blades
for cutting holes in walls to accommodate switches or power sockets
for removing grouting from between ceramic tiles

The multi-tool is intended to be operated indoors in dry, well-illuminated, and adequately ventilated conditions. The multi-tool is not intended to be used on wet materials or surfaces. Do not use the product in any way other than those stated for the intended use.

WARNING
Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

MULTI-TOOL SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Always wear safety goggles while operating the tool. Wear a dust mask when the dust is produced.

WARNING
Dust from certain paints, coatings, and materials may cause irritation or allergic reactions. Dust from wood such as oak, beech, MDF, and others are carcinogenic. Only qualiﬁ ed specialists should be allowed to use the product on asbestos materials.

WARNING
The product should never be connected to a power supply when assembling parts, making adjustments, cleaning, performing maintenance, or when not using it. Disconnecting the product from the power supply will prevent accidental starting that could cause serious injury.

When working in walls, ceilings or floors, take care to avoid electric cables and gas or water pipes.

WARNING
Metallic accessories will become hot during use and could result in skin burns if contacted by the operator. Wear gloves when changing accessories. Take care when setting down the tool between operations to prevent damage or injury.

Do not use cutting accessories that are damaged, cracked or do not fit securely to the product.
Ensure that the lock-on switch is not in the on position before inserting the battery pack.
The multi-tool creates vibrations that move the accessory. The vibrations may cause discomfort if the product is operated for long periods of time. Take a rest often, especially if you feel discomfort in the arm, wrist, or fingers. Choose a speed setting that will get the work completed efficiently. Read the Residual Risks and Risk Reduction sections for more information on the vibration-related injury.
Clamp the workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage. Do not hold the material you are sanding by hand.
Do not use sanding paper larger than needed. Extra paper extending beyond the sanding pad can also cause serious lacerations.
The ambient temperature range for the tool during operation is between 0°C and 40°C.
The ambient temperature range for tool storage is between 0°C and 40°C.
The recommended ambient temperature range for the charging system during charging is between 10°C and 38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

WARNING
To reduce the risk of ﬁ re, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in ﬂuid or allow a ﬂuid to ﬂow inside them. Corrosive or conductive ﬂ uids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.

The ambient temperature range for batteries during use is between 0°C and 40°C.
The ambient temperature range for battery storage is between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and regulations.

Follow all special requirements on packaging and labeling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise and the operator should pay special attention to avoid the following:

Injury caused by dust
- Wear eye protection at all times.
- Wear respiratory protection masks containing filters appropriate to the materials being worked. Ensure adequate workplace ventilation.
- Do not eat, drink or smoke in the work area.
Injury caused by noise and vibration
- Wear ear protection.
- Do not operate the product for long periods of time. See “Risk reduction”.
Risk of electrocution if electric cables are cut
- Always hold the product by designated handles. Do not touch the cutting blades or metal parts of the product.

RISK REDUCTION

It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness and blanching of the ﬁ ngers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking, and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:

Keep your body warm in cold weather. When operating the product, wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
After each period of operation, exercise to increase blood circulation.
Take frequent work breaks. Limit the amount of exposure per day.

If you experience any symptoms of this condition, immediately discontinue use and see your doctor about these symptoms.

WARNING
Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

KNOW YOUR PRODUCT

LED light
Blade locking screw
Speed control
On/off switch
Lock on switch
Handle, insulated grasping surface
Plunge cut blade
Flush cut blade
Sanding pad
Sandpaper
Adaptor storage slot
Adaptor */**
Hex key
Battery port $RYOBI-R18MT3-18V-ONE+-Multi-Tool-fig- $2$$

Compatible with BOSCH accessories. BOSCH is a registered trademark of Robert Bosch GmbH.
Compatible with DREMEL accessories. DREMEL is a registered trademark of Robert Bosch Tool Corporation.

OPERATION

The product is supplied with an extra adapter for use with other brands of cutting, scraping, and sanding accessories. The adapter may be turned over for use with the desired brands of accessories. Do not use the adapter with RYOBI accessories supplied with your tool.

Secure workpieces that can move with a clamp to prevent movement during sanding or cutting operations. Do not hold the workpiece by hand. An inadvertent slip while operating the product may cause serious personal injury.
When making a plunge cut into soft materials like wood and plasterboard using the cutting accessory, gradually bring the vibrating blade to the workpiece. Do not push the vibrating blade hard into the material to be cut. Let the product do the work and concentrate on keeping the product and the cutting accessory stable in the position you wish to make the cut.
Take extra care when cutting in non-ferrous metals. The vibrating cutting blade may skip around before beginning the cut. If necessary, drill some holes along the line to be cut before you start cutting.
If the cutting accessories become jammed in the workpiece, switch off the product and disconnect from the power supply. If the cutting accessory cannot be removed easily, allow the cutting accessory to adequately cool before releasing the cutting accessory from the product. Wear gloves and use hand tools, such as pliers or wrenches, to remove the cutting accessory from the workpiece.

OVERCURRENT PROTECTION
When overcurrent is detected, the product will automatically switch off. If the product stops working, release the trigger and then apply it again. The product should again start working.

MAINTENANCE

WARNING
The product should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product will prevent accidental starting that could cause serious injury.

When servicing, use only the original manufacturer’s replacement parts. Use of any other parts may create a hazard or cause product damage.

WARNING
For greater safety and reliability, all repairs should be performed by an authorized RYOBI service center.

GENERAL
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.

WARNING
Do not, at any time, let brake ﬂ uids, gasoline, petroleum-based products, and penetrating oils, come in contact with plastic parts. They contain chemicals that can damage, weaken, or destroy plastic.

The dust from plaster and wallboard is abrasive and may cause premature failure of the product if it is allowed to enter the motor area. Thoroughly clean the product after use by using a brush and a vacuum. Take care not to push dirt into the ventilation openings. Beware of using compressed air to clean the product because dust and grit can cause serious eye injury.

LUBRICATION
All of the bearings in the product are lubricated with a sufficient amount of high-grade lubricant for the life span of the product under normal operating conditions. Therefore, no further lubrication is required.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environment-friendly recycling.

SYMBOLS ON THE PRODUCT

Safety alert
CE conformity
No-load speed
Volts
Direct current
Eurasian Conformity Mark
Please read the instructions carefully before starting the machine.
Ukrainian mark of conformity
Wood – Plunge and ﬂush cuts
Non-ferrous metal – Plunge and ﬂush cuts
Plastics – Plunge and ﬂush cuts
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

SYMBOLS IN THIS MANUAL

Note
Parts or accessories are sold separately
Unlock
Lock
Speed, minimum
Speed, maximum

The following signal words and meanings are intended to explain the levels of risk associated with this product:

DANGER
Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

WARNING
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

CAUTION
(Without Safety Alert Symbol) Indicates a situation that may result in property damage.

What’s In The Box

$RYOBI-R18MT3-18V-ONE+-Multi-Tool-fig- $1$$

INSTALLATION INSTRUCTION

$RYOBI-R18MT3-18V-ONE+-Multi-Tool-fig- $3$$ $RYOBI- R18MT3-18V-ONE+-Multi-Tool-fig- $4$$

Multi-tool adaptor

Compatible with BOSCH accessories. BOSCH is a trademark of Robert Bosch GmbH.
Compatible with DREMEL accessories. DREMEL is a trademark of Robert Bosch Tool Corporation.

Product Specifications

Product specifications

18V Multi-tool
Model
Voltage
No-load speed
Oscillation angle
Weight – excluding battery pack
Weight (According to EPTA- Procedure 01/2003)
Measured sound values determined according to EN 62841:
A-weighted sound pressure level
Uncertainty K
A-weighted sound power level
Uncertainty K
Wear ear protectors.
**** The vibration total values (triaxial vector sum) determined according to EN 62841:
Sanding with a sanding pad
Uncertainty K

Replacement parts

Adapter
28-mm Plunge cut blade
88-mm Flush cut blade
Sanding pad
Sanding paper, 60 grit
Sanding paper, 80 grit
Sanding paper, 120 grit

Battery and charger

Compatible battery pack (not included)

Lithium-Ion

The compatible charger (not included)

WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However, if the tool is used for different applications, with different accessories, or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintaining the tool and the accessories, keeping the hands warm, and organization of work patterns.

RYOBI WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

The warranty period is 24 months for consumers and commences on the date the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only to new products.
There is a possibility to extend a part of the range of power tools (ACDC) warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for the extended warranty is clearly displayed in stores and/or on the packaging and is contained within the product documentation. The end user is required to register his/her newly- acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid f the product has been misused used contrary to the instruction manual or has been incorrectly connected to a power supply. This warranty does not apply to:
- any damage to the product that is the result of improper or lack of maintenance
- any product that has been altered or modified
- any product where original identification (trademark, serial number) markings have been defaced, altered or removed
- any damage caused by non-observance of the instruction manual
- any product not displaying the CE approval mark on the rating plate
- any product that has been attempted to be repaired by a non-authorized warranty service center or without prior authorisation by Techtronic Industries
- any product connected to the improper power supply (amps, voltage, frequency)
- any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
- normal wear and tear spare parts
- inappropriate use, overloading of the tool
- use of non-approved accessories or parts
- Power tool accessories provided with the tool or purchased separately, including but not limited to screwdriver bits, drill bits, abrasive discs, sandpaper and blades, lateral guide, etc.
- Components (parts and accessories) are subject to natural wear and tear, including but not limited to service & maintenance kits, carbon brushes, bearings, chuck, SDS drill bit attachment or reception, power cord, auxiliary handle, transport carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact Wrench pins & springs, etc.
For servicing, the product must be sent or presented to an RYOBI-authorised service station listed for each country in the following list of service station addresses. In some countries, your local RYOBI dealer undertakes to send the product to the RYOBl service organization. When sending a product to an RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with the sender’s address, and accompanied by a short description of the fault.
A repair/replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries, delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected
This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey, and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRE

Any request or issue with the product can be addressed to your local authorized service centers (visit www.ryobitools.eu) or directly to Techtronic Industries GmbH, Max Eyth Strafße 10, 71364 Winnenden, Germany. Please state the serial number and product type printed on the label.

DECLARATION OF CONFORMITY

Drill driver
We declare under our sole responsibility that the product mentioned below fulfills all the relevant provisions of the following European Directives, European Regulations, and harmonised standards.

Authorized to compile the technical file:

RDD18C