RYOBI R18DDP Drill-Driver Accumulator Instruction Manual
- June 9, 2024
- RYOBI
Table of Contents
R18DDP
ORIGINAL INSTRUCTIONS
Important! It is essential that you read the instructions in this manual before operating this machine.
Subject to technical modifications
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
DRILL DRIVER SAFETY WARNINGS
a) Use auxiliary handle(s), if supplied with the tool. Loss of control can
cause personal injury.
b) Hold power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
c) Hold power tool by insulated gripping surfaces, when performing an
operation where the fastener may contact hidden wiring. Fasteners contacting
a “live” wire may make exposed metal parts of the power tool “live” and could
give the operator an electric shock.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and regulations.
Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.
INTENDED USE
- Drilling into a variety of materials:
- wood
- metal
- plastic
- ceramic - Driving and removing screws
Do not use this product in any way other than those stated for intended use.
MAINTENANCE
WARNING
The product should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product will prevent accidental starting that could cause serious injury.
a) When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.
b) Avoid using solvents when cleaning plastic parts. Most PT plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
c) Do not at any time let brake fluids, gasoline, petroleum based products, penetrating oils, etc., come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic.
d) Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.
e) For greater safety and reliability, all repairs should be performed by an authorised service centre.
LUBRICATION
All of the bearings in the product are lubricated with a sufficient amount of high grade lubricant for the life span of the product under normal operating conditions. Therefore, no further lubrication is required.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental friendly recycling.
SYMBOLS
Safety alert
CE conformity
GOST-R conformity
Please read the instructions carefully before starting the machine.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Product specifications|
---|---
Voltage| 18 V
Chuck| 2-13 mm
Switch – Variable speed|
No load speed (drill mode): |
Lo speed| 0 – 440 min-1
Hi speed| 0 – 1600 min-1
Clutch (Positions)| 24
Maximum torque| 45 Nm
Maximum drilling capacity (Wood)| 32 mm
Maximum drilling capacity (Metal)| 13 mm
Weight – excluding battery pack| 1,38 kg
Weight – according to EPTA Procedure 01/2003| 1,80 kg
Product specifications|
---|---
Measured sound values determined according to EN 60745:|
A-weighted sound pressure level| LpA = 79 dB(A)
Uncertainty K| 3 dB(A)
A-weighted sound power level| LWA = 90 dB(A)
Uncertainty K| 3 dB(A)
Wear ear protectors.|
The vibration total values (triaxial vector sum) determined according to EN
60745:|
Vibration emission value|
Screw driving without impact| ah = 1,3 m/s²
Uncertainty K| 1,5 m/s²
Drilling into metal| ah,D = 1,8 m/s²
Uncertainty K| 1,5 m/s²
Battery and charger| |
---|---|---
Compatible battery pack (not included)| BPL-1820
BPL-1815
RB18L13
RB18L15
RB18L26
RB18L40| BPP-1815
BPP-1817
BPP-1813
Compatible charger (not included)| BCL14181H
BCL14183H
BCS618| BCS618
BCL14181H
BCL14183H
WARNING
The vibration emission level given in this information sheet has been measured
in accordance with a standardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a preliminary assessment of
exposure. The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration
emission may differ. This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but not
actually doing the job. This may significantly reduce the exposure level over
the total working period. Identify additional safety measures to protect the
operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
Guarantee
In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.
-
The guarantee period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
-
There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data which are required to enter online and they have to accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty. Your statutory rights remain unaffected.
-
The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to:
– any damage to the product that is the result of improper maintenance
– any product that has been altered or modified
– any product where original identification (trade mark, serial number)
markings have been defaced, altered or removed
– any damage caused by non-observance of the instruction manual
– any non CE product
– any product which has been attempted to be repaired by an nonqualified professional or without prior authorization by Techtronic Industries
– any product connected to improper power supply (amps, voltage, frequency)
– any damage caused by external influences (chemical, physical, shocks) or foreign substances
– normal wear and tear of spare parts
– inappropriate use, overloading of the tool
– use of non-approved accessories or parts
– carburettor after 6 months, carburettor adjustments after 6 months
– power tool accessories provided with tool or purchased separately. Such exclusions include but is not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide
– components (parts and accessories) subject to natural wear and tear, including but not limited to carbon brushes, chuck, power cord, auxiliary handle, sanding plate, dust bag, dust exhaust tube -
For servicing, the product must be sent or presented to an RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to an RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
-
A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will have to be paid by the sender.
-
This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.
AUTHORISED SERVICE CENTRE
To find an authorised service centre near you, visit http://uk.ryobitools.eu /service-agents-ryobi.htm.
EC declaration of conformity
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product
Drill Driver
Model number: R18DDP
Serial number range: 44405601000001-44405601999999
is in conformity with the following European Directives and harmonised standards
2011/65/EU, 2006/42/EC, 2004/108/EC,
EN 60745-1: 2009 + A11: 2010, EN 60745-2-1: 2010, EN 60745-2-2: 2010,
EN 55014-1: 2006 + A1: 2009 + A2: 2011,
EN 55014-2: 1997 + A1: 2001 + A2: 2008
Andrew John Eyre (BEng, CEng, MIET)
Vice President, Regulatory & Safety
Winnenden, Jul. 22, 2013
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
961152184-01
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>