GTSTART L8 RGB LED Neon Rope Light 16.4FT Instructions
- June 9, 2024
- GTSTART
Table of Contents
GTSTART L8 RGB LED Neon Rope Light 16.4FT Instructions
Remote Control
Product Parameters
- Model NO.: L8-Neon Rope Lights-16.4FT
- Waterproof Level: IP65 Waterproof
- LED Type: 3535 RGB
- Input Voltage of Adapter: AC 100V-240V
- Length of Strip Light: 16.4ft/5m
- Whether it can be cut: Yes Controller Mode
| Switch 20 static colours with key
---|---
| Power of /on button with brightness/ speed adjustment In the static color
mode. piess this key to adjust the brighteness, which consist of 10 1 levets.
Pressing this key in dynamic mode is to increase or reduce the color changing
speed which ! t consist of 10 levels
| Press this key to switch the color I change mode in dynamic mode 1 There are
20 modes can be chosen I automatically and circularly.
44-keys Infrared Remote Control
The controllable distance is within 8m,you can adjust brightness, change static colors or other effects
- Tum on/off
- Pause/Run: Using under below mode only:JUMP3; JUMP7; FADES; FADE7; FLASH; AUTO
- You can adjust the brightness level of the 20 static colors from bright to dim (8 levels)
- You can adjust the brightness levels of the 20 static colors from dim to bright (8 levels)
- 20 Static Colon
- The strengthen and weaken key of Red , Green and Blue, works under DIY Mode. Invalid in other mode.
- Press DIY 1, then press 6 ( the arrow key of Red , Green and Blue ) to adjust color, then press any other keys to save automatically, DIY2-DIY6 personal operation
- JUMP3: 3 colon jump change
- JUMP7: 7 colors jump change
- FADE3: 3 colors flashing
- FADE7: 7 colors flashing
- Turn on the white light strobe mode
- Under the modes: JUMP3. JUMP7. FADE3. FADE7. FLASH AUTO,you can speed up the change(8 levels)
- Under the modes: JUMP3. JUMP7. FADE3. FADE7. FLASH AUTO,you can slow down the change(8 levels)
- JUMP3 JUMP7 . FADE3 FADE7 and FLASH mod can loop automatically (
16.4 Music Models
APP Mode
This APP program requires that the minimum systems of your phones is Andriod
4.3 or i0S8.0. No limit for mobile phone configuration. You can download APP
by scanning QR codes on iOS or Android systems. Use Apps with scanning
function such as browser to scan the QR code. Please open the Neon strip
lights control APP on your phone, by which you can connect one or more the
Neon strip lights through • b Bluetooth and able to set and control multiple
LED strip.
Functions are listed as follows:
- Adjust 60,000 kinds of colon for the Neon Strip Lights;
- There are 20 style modes for you to choose when use APP control or controller box
- In the music mode, the colors of strip lights change automatically according to the music rhythm, which is absolutely beautiful If the phone system is Android, this app will automatically sync the songs that have been downloaded in your mobile phone. If the phone system is iOS, you need to connect your mobile phone to the computer and import the songs from the computer to your mobile phone. Then the app will automatically syncs the songs you have imported.
- In the Mic mode, colors adjusted automatically based on the ambient sound, the phone Mic or external Mic can be chosen
- 5. Be your light “Alarm clock”, the Neon strip lights have timing function. You can preset the time to turn on/off your Neon strips lights. Then it turns on or off automatically on time every day.
- Long distance control has no direction restriction and multiple controls are allowed.
- The Neon strip lights have memory function. Last mode settings can be kept.
- Once has been connected, your phone would connect to the light strips automatically when bluetooth is available.
- The controllable distance is within 8m , you can adjust brightness, change static colors and other effects.
HAPPYLIGHTING APP
When your device can’t connect the lights automatically, follow the steps
below: Android <<<<<<<<<<<<<<<<<<<<
Method 1: Click ‘My Devices’ to refresh (on the top left corner), then it
shows ‘connected successfully’.
Method 2: If the first step fails, you need to exit the App and close its
‘process’ in the background completely, then open again.
Method3: If the all steps fail, you need to exit the App and close its
‘process’ in the background completely, turn off the bluetooth, then turn on
the bluetooth, and open the App again. IOS«««««««««««
Method 1: Exit the App, close its ‘process’ in the background, and then
open the App again.
Common Troubleshooting
The controller was connected the power, but not light up
- Check the input power supply: please use the power adapter that we equipped or other adapters with the same specification as ours. The input voltage must meet the voltage requirment of the strip lights. When the input voltage is lower than requirement, the strip lights will not be turn on, while higher voltage may damage the circuit. The output power of the adapter (KW value) must equals to, or higher than the power of the Neon strip lights
- Check whether the connector is connected correctly with the strip lights. Make sure each interface is connected correctly.
- Check whether the remote control is open.
- If the Neon strip lights are able to light up, but the remote control does not work or can’t control LED light.
- Check whether the insulation sheet is removed from the remote control
- Make sure the battery on the remote control is installed correctly
- Ensure that the remote is working within 8 meters and aligned to the infrared receiver of the controller.
- Try to replace the battery.
How to Connect Them Correctly? NOTE: The arrows must be aligned, otherwise will not work.
WARNING
- EX) NOT I FIRE
- CHILDREN UNDER THE AGE OF 16 St IOULD USE THIS PRODUCT UNDER ADULT SUPERVISION_
E-MAIL: service0863h@outlook.corn If you rove any questions. plan ar4acl our customer saw” we ad PeP1/4 you warn 24 hours.
Warning Statement
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any Changes or
modifications not expressly approved by the party responsible for compliance
could void the users authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B cigital device, pursuant to part 15 of the FCC Rules. These imits are
designed to prcnide reasonable protection against harmful interference in a
residential installation. This equipment Generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful intertrence to redo commurications. However,
there is no guarantee that interference will not cccure in a particular
installation. If this equipment does cause harmful interference to radio a
television receptbn, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: –
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>