PRIMERUS PRODUCTS LLC PD-010-100 Zero Overspray Precision Container Irrigation Instruction Manual

PRIMERUS PRODUCTS LLC PD-010-100 Zero Overspray Precision Container Irrigation

ZERO OVERSPRAY PRECISION CONTAINER IRRIGATION

REMOVE THE POT-DRIPPER FROM PACKAGE

Remove the Pot-Dripper from the box and rotate the stake to a 90ο angle from the tubing ring. Be sure you have rotated it in a direction so the hollow 1/8” supply connection points outward from the ring, and the solid 1/8” shutoff barb points into the center of the ring.

INSTALL THE POT-DRIPPER IN YOUR CONTAINER

Seat the Pot-Dripper in your container media, using the stake to anchor it. Refer to Table 1 for ring diameter recommendations for standard container sizes.

PREPARE 1/8” SPAGHETTI TUBE SUPPLY

Determine the length of 1/8” Primerus Spaghetti tubing required to reach from the hose lateral to the desired location of the Pot-Dripper. Length should be adequate to allow for thermal expansion and contraction of laterals

| Pot-Dripper End, 90°
---|---
| Insertion End, 45° (no hub dripper)
| Insertion End, 90° (with hub dripper)

If not using a hub dripper, cut one end of the Spaghetti Tube (insertion end) at a 45° angle and the opposite end (Pot-Dripper end) at a 90° angle. If using a hub dripper cut both ends at 90ο and insert one end onto the 1/8” output barb of the hub dripper

INSTALL 1/8” SPAGHETTI TUBE ON POT-DRIPPER

Insert the 90° end of the 1/8” Spaghetti tube (or the end without the hub emitter) onto the hollow 1/8” supply post of the Pot-Dripper stake, pushing it all the way to the bottom to fully seat it.

PUNCH A HOLE IN YOUR SUPPLY LATERAL

Use an 1/8” Primerus Hole Punch to create a hole in your ½”, ¾” or 1” supply lateral. For guidance on the correct diameter supply laterals for your operation, see Table 1 on the last page of this flyer.

INSERT THE SPAGHETTI TUBE INTO YOUR LATERAL

If you are not using a hub dripper, insert the 45° end of the Spaghetti Tube directly into the hole you have created in your lateral hose far enough so the end of the Spaghetti Tube is approximately at the center of the hose. Be careful not to insert it so far that it makes contact with the back wall of the hose. The properties of the Primerus Spaghetti tube will create a strong, leak-free seal without the need for a barb.

If you are using a hub dripper, insert the ¼” input barb of the hub dripper into the hole you have created in the lateral hose.

USE CORRECT PRESSURE

You are now ready to irrigate. If you are not using a hub dripper (non- compensating mode), pressurize the lateral hose to 15 psi for accurate flow rates. Use a pressure regulator to ensure consistent pressure control. If you are not using a hub dripper, pressure in the lateral supply hose can be set to any level between 15 and 50 psi. Using pressures higher than 50 psi can result in damage to the lateral hose.

USE CLEAN WATER

Always use clean water in drip irrigation systems. Primerus Products recommends
120 mesh equivalent filtration for the Pot-Dripper. Use a screen filter for inorganic contaminants, or a disk or media filter if your water contains organic matter.

TABLE 1
POT-DRIPPER SELECTION CHART

Pot-Dripper Model

| Container Size| Ring
Diameter| No.
Drippers| Flow Rate
at 15 psi| Optional
Hub Dripper|

Max Containers per Row*

---|---|---|---|---|---|---

PD-010-100

| 5-7 Gal| 9.6in.| 5| 2.5 GPH| 2GPH| 105 (1/2″ lateral)
240(3/4″ lateral)

450{l” lateral)

PD-012-100

| 10-15 Gal| 11.5 in.| 6| 3.0GPH| 3.2GPH| 75 (1/2″ lateral)
175 {3/4″ lateral)

320 (1″ lateral)

PD-014-100

| 20-25 Gal or

24-30″ Box

| 13.4in.| 7| 3.5GPH| 3.2GPH| 52(1/2″ lateral)
120 (3/4″ lateral)

230(1″ lateral)

Components and Accessories

(for use with hub dripper)
TPE-12531-48| l./S.” Spa~hetti Tube, 48″ length, 90° end, box 1000 (for use with hub dripper)
TPE-·12531-36-45| 1/8 ‘ S aghettl Tube, 36″ len.g h, 45″ end, box 1000 ,(for use without hub dripper)
TP E-12531-100| ll/8″ S aghetti Tube, 48″ length, 4-S” end, box 1000 {for use without hub drip er)
TP E-12531-100| 1/8″ Spaghetti Tube, JDJ-foot roll
· PE-12531-1000| l/8,” Spa~hetti Tube, 100)-fooil: roll
CX:O-HP · :125| Primerus 1/8” Hole Punch

Primerus Products, LLC
• Encinitas, CA
• 760.452.6399
• www.PrimerusProducts.com

References

• Primerus Products, LLC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>