gigawave GIGA-AC-BW260 Enterprise Level Multi Function Flow Control Gateway Installation Guide
- June 4, 2024
- gigawave
Table of Contents
gig wave GIGA-AC-BW260 Enterprise Level Multi-Function Flow Control
Gateway
01/Route Connection
02/Route Settings
Login Device
Connect Lan port of device to PC,login in via 172.0.1:2011 ,ID/Password: admin
,as below:
Note:
Please check the IP address of default port above .
WAN port settings
(Network configuration) (Interface Configuration) “External network
configuration”, select the network port to configure, and configure the
information of the external network, as shown in the following
image:
Internet access: (choose how to access the Internet according to the actual
situation)
ADSL/PPPOE:
Fill in bandwidth account numbers and passwords (this type of Internet access
is recommended) Fixed IP: Fill in IP, mask, gateway and DNS provided by the
operator
DHCP:
Direct access to lines provided by the operator to obtain IPLine interruption
check: detect whether the line is connected to the network, if the line is not
accessible or the linequality is poor, the packet is serious, the route is
automatically processed, does not load to the Line.It is recommended to enable
line interrupt detection.Bandwidth configuration: configure the bandwidth of
the line, such as the dial-up fiber of the upstream 4M downlink 100M, can be
configured with behavior 500KB, downside 10000KB.Configure the line Bandwidth
is important, and intelligent streaming is automatically streamed based on the
bandwidth that is matched. (The”Enable Smart Streaming” option needs to be
checked to configure bandwidth values for effective)
Physical port division
This feature supports separate and merge port divisions.When the main road is
recommended to use the merge port division, that is, open All LAN ports are
one LAN1 port function. If it is bypass mode, it is recommended to turn this
feature off.Select the corresponding according to the actual situation
Physical port division type, check “Merge all LAN ports as one intranet port
(LAN1).”
Note: After the definition of the physical port feature is modified, the route
needs to be reconfigured. (Note: The version of the X86 platform does not
support Ethernet port merge).
AP Upgrade Management
AP Upgrade Management allows you to upload the AP version that needs to be
upgraded to the device, and then select the AP list in full or selected to
upgrade, while also supporting the AP remote upgrade.
05/Configure shunt rules
Configuring shunt rules
A single line can not configure a shunt rule; (Network configuration)
Multi-line shunt rule, point Hit Add creates a policy shunt rule, selects the
shunt mode, selects which apps the line hosts, and click OK after
checking.
Note:
Multi-line load balancing is achieved by shunt rules.
Configure bandwidth speed limit policy
Description: Routing has intelligent flow control function, configuration
speed limit strategy, the purpose is to prevent the endonet machine poisoning,
or advertising uncontrolled Upload, usually the speed limit up to 100-300KB,
the downlink speed limit can be properly l iberalized, such as the speed limit
of 1000-3000, usually recommended The speed limit does not exceed one-third of
the total bandwidth.
For example: a 50M peer fiber, then each machine speed limit up 100-300KB,
down1000-3000 KB can be, advanced recommendation configuration P2P The limit
allows 70% of the allowed for the upstream and 70% allowed for the downstream.
As shown above (ANY means arbitrary, that is, anyone, any
time)
03/AC Management
AP Device List
The AC controller feature allows centralized management and release
configuration of the AP devices connected to it, with parameters including
Line channels, SSIDs, transmit power, encryption modes and keys, AP coverage
thresholds, number of access users, and VlAunID, as follows As shown in the
figure:
Note:
The default configuration issued by AP is achieved by establishing the
template, with one template for each model.Only in the AC list should The
template of the corresponding model will be released normally. Note: An AP
model can also create multiple templates.Apply to the same floor or geography
of the same model A scene with a different location.
AP Device Configuration
AP device configuration, is a single AP or multiple APs in the list of
parameter modifications, including the wireless state on or off, The
modification of the channel, the modification of the wireless bandwidth mode,
the modification of the AP coverage threshold, the modification of the
transmit power, and the marking of the device location.
04/Authentications
Enable authentication to the Internet
Enable authentication Online, means that only WeChat authentication, PPPOE
dial-up authentication, WEB password authentication, IP authentication, MAC
authentication.Users can only access the Internet, for example, allow the user
PPPOE dial-up Internet access under LAN1, scertified Internet access ,
“Certification switch”, select LAN1, enable the authentication network switch,
check the type of “PPPOE dial” that allows Internet access, click
Save.
PPPOE Authentications
Users who use PPPOE dial-up Internet access need to enable PPPOE services at
the intranet, such as PPPOE services on LAN1. (Certified Internet Access)
(PPPOE Certification) (PPPOE Advanced Options) and select the
app.
06/Safety
End-network anomaly detection
Turn on DHCP detection to detect the presence of other DHCP servers in the
intranet; Turn on Loop Detection to check the contentford for loops (for
intranet fault positioning).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>