lumiere Lanterra 1002 LED Accent and Flood Light Instruction Manual

1002 LED Accent and Flood Light
Instruction Manual Installation Instructions – Lanterra – MB (Ground Mount Recessed Box)
Installation Instruction Sheet

Lanterra 1002 LED Accent and Flood Light

WARNING
Make Certain Power is OFF before starting installation or attempting any maintenance.
WARNING
Risk of Fire/Electric Shock. If not qualified, consult an electrician.
WARNING
Risk of Electric Shock – Disconnect power at fuse or circuit breaker before installing or servicing.
WARNING
Risk of Personal Injury – Fixture may become damaged and/or unstable if not installed properly.

• Do not mount luminaire within 6” of a combustible surface.
• Do not handle luminaire by the glass. Do not touch LEDs.

WARNING
Risk of Burn – Disconnect power and allow fixture to cool before servicing.
Note:
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.
Note:
This lighting fixture has been shipped complete with one of several mounting options. Please follow the installation instructions specific to the catalog part that you ordered.
Note:
Care must be taken not to set lighting fixture down on optical lenses or lift the fixture in the lens area.
Note:
Specifications and dimensions subject to change without notice.
IMPORTANT: Read carefully before installing fixture. Retain for future reference.
GENERAL: Upon receipt of the fixture, thoroughly inspect for any freight damage which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the packing slip with the fixture label on the housing to assure you have received the correct material.
SAFETY: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under installation section.
APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area of limited ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation and  insertion of photo control or shorting cap (if so equipped). Do not install the fixture near combustible materials or locate next to airflow blocking surfaces within 6 inches. Best results will be obtained if installed and maintained according to the following recommendations. ![lumiere Lanterra 1002 LED Accent and Flood Light

• fig 1](https://manuals.plus/wp-content/uploads/2023/02/lumiere-Lanterra-1002 -LED-Accent-and-Flood-Light-fig-1.png)

Note: *Constructions built before Jan 2022 may have gray wire for 0-10 dimming control present. In these cases, the installer will label the gray building wire as a 0-10  dimming wire and connect to our product’s pink 0-10V dimming control wire.
Reference NFPA70 (2020 NEC), section 410.69.

INSTALLATION

Soil Burial

1. Excavate soil for housing placement and conduit.
2. Contour shape of hole for housing, allowing for additional 3” minimum under and around hosing for placement of pea gravel.
3. Line bottom and side of hole conduit (see “All Instructions”). Do no bury driver container up to the top of housing cover.
4. Place soil up to bottom of lip. Build up the soil around container to make a crown that will promote water runoff.
5. Do not place in-ground container in low areas or other areas where water can accumulate and stand for long periods of time. (Figure 2.)

Concrete Pour

1. The in-ground driver housing should be placed on 4” minimum of par gravel, with soil below to promote drainage.

2. Attach in-ground driver to conduit (see “All Instructions”).

3. Concrete may be installed up to top of lip.
   Note:When possible and not dangerous or hazardous, crown surface to promote water runoff.

4. Do not place in-ground container in low areas or other areas where water can accumulate and stand for long periods of time. (Figure 3.)

All Installations

1. Seal the input and through conduits to prevent water intrusion from conduit to wiring compartment.

2. Mount inlet fitting (two 3/4 NPSM female) to conduit. Use Teflon tape or other sealing compound to seal conduit to prevent water entry.

3. You may use a re-enterable potting compound to temporarily plug conduit entries when pouring re-enterable potting compound.
   Note: Use enclosed dust seal compound to temporarily plug conduit entries when pouring re-enterable potting compound.

4. It is recommended to install 1” conduit at the level of the soil under pea gravel below fixture for better water drainage.

5. Length of the pipe may vary to ensure proper water runoff. Avoid installing the pipe right above the wire conduit.

Input Wiring

1. Confirm input power requirements with label on the driver compartment.
2. To open Transformer Wiring Compartment, loosen four allen screws with 9/64” hex key.
3. Use input wire rated for at least 90°C
4. Use waterproof wire nuts to connect to input power. See wiring table for reference
5. Strip wires 5/8”. DO NOT pretwist. Twist connector onto wires while pushing firmly until hand tight. DO NOT over torque.
6. Swipe excess sealant in and around conductors. Wire line voltage power to black wire (line), white (common) to white,. green (ground) to green wire. If used, connect purple (dim +) and pink (dim -) wires to dimming control. If dimming is not used, cap purple and grey wires seperately with wire nuts.

Warranties and Limitation of Liability

Please refer to www.cooperlighting.com for our terms and conditions.

Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
© 2022 Cooper Lighting Solutions
All Rights Reserved
Printed in USA
Imprimé aux États-Unis
Impreso en los EE. UU.
Publication No. IL506002EN
March 4, 2022
Cooper Lighting Solutions is a registered trademark.
All trademarks are property of their respective owners.
Product availability, specifications, and compliances are subject to change without notice.

References

• The domain name notice.la is for sale

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>