hama 00176588 WiFi LED Downlight Instruction Manual

00176588 WiFi LED Downlight
Instruction Manual
00176578 00176579 00176588 00176589
00176608 00176609 00176610 00176611

WiFi LED-Downlight

00176588 WiFi LED Downlight

Step 1: cut the hole on ceiling
Step 2: connect power (AC 220 – 240 V)

Step 3: Vertically put the spring buckle and then release on the hole of ceiling
Step 4: Finish installation

Operating Instructions

Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.
1. Explanation of symbols used on the product label

| Electrical device of safety class II.
Protection against electric shock thanks to reinforced or double insulation of live parts.
---|---
**| The product is intended only for use inside buildings.
| Only use in a dry environment.
| No heat-insulating materials must be in contact with the light.
| The product must only be used with alternating current.
| Non-dimmable.**
The lamp is not suitable for use with a conventional dimmer.
| The article may only be connected by a qualified electrician who complies with national regulations and those of the local energy  supply company, and who has sufficient knowledge regarding installation locations, fire protection and electrical installation work.

Explanation of warning symbols and notes

Risk of electric shock
This symbol indicates a risk of electric shock from touching product parts carrying hazardous voltage.
Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.

Package contents

Package contents for 176578, 176588, 176608, 176610:

• 1 WiFi built-in spotlight
• 1 quick-start guide

Package contents for 176579, 176589, 176609, 176611:

• 3 WiFi built-in spotlight
• 1 quick-start guide

Safety instructions

• This product is intended for private, non-commercial use only.
• This product is intended exclusively for installation in suspended ceilings or suitable built-in recesses or concrete built-in housings.
• Use the product only for the intended purpose.
• Do not drop the product and do not expose it to any major shocks.
• Do not operate the product outside the power limits specified in the technical data.
• Do not modify the product in any way. Doing so voids the warranty.
• Children must not play with the device. Cleaning and user maintenance must not be carried out by children without supervision.
• As with all electrical products, this device should be kept out of the reach of children.
• Dispose of packaging material immediately in accordance with the locally applicable regulations.
• The product should only be installed in self-contained rooms. It is not suitable for installation in bathrooms.
• The product must only be operated on a supply network as described on the type plate.
• Before mounting, check that the ceiling you have chosen is suitable for the weight to be mounted. Also make sure that there are no electric, water, gas or other lines running through the ceiling at the mounting site.
• Electrical cables must never become trapped or twisted between the product and the surface.
• If the product is attached to a metal surface, it must be connected to an earth lead or the installation’s potential equalizing cable.
• These built-in lights are not compatible with dimmer switches, motion sensors or dimmers.
• Protect the product from dirt, moisture and overheating and use it in dry rooms only.
• Only use the article under moderate climatic conditions.
• Do not use the product in areas in which electronic products are not permitted.
• Do not use the product in a damp environment and avoid splashing water.
• Do not bend or crush the cable.
• Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
• Do not continue to operate the device if it is visibly damaged

Warning

• Please note that lights (even LEDs) can generate heat and may become hot. Always let the light cool down for a few minutes before touching it.
• The device may only be operated on a 230 V 50 Hz AC voltage network. Work on the 230 V network must only be carried out by an electrician certified in your country.  The applicable accident prevention regulations must be adhered to.
• To avoid an electric shock from the device, please disconnect the mains voltage (switch off the automatic circuit breaker). Failure to comply with the installation instructions can cause fires or other hazards.

Risk of electric shock
Do not open the product and do not operate it if it is damaged, if smoke, a strange smell or loud noises are coming from it. Immediately contact your dealer or our service department (see item “Service and Support”).

Note
The light source of this light is not replaceable; when the light source has reached the end of its life, you need to replace the entire light.
Warning
Never look straight into the light source and do not aim its beam of light straight into the eyes of other people or animals. This could damage your/their eyes.

Example installation in wood / drywall ceiling:

1. Before commencing any installation, maintenance or repair work, please disconnect the power circuit by disconnecting the fuse.
2. Secure the power circuit against being switched back on.
3. Check that the required minimum installation depth of 80 mm (47 mm light + 33 mm clearance) is available. The clearance between the upper edge of the light and the  ceiling must not be less than 33 mm to allow ventilation. The minimum distance between the lights and flammable materials must be no less than 50 cm. Do not cover the light with any heat-insulating material.
4. Mark out the position where the light is to be installed.
5. Create an installation opening with a diameter of 75 mm using a suitable hole saw. Take care not to disturb any hidden installation or supply lines.
6. The terminal points (e.g. terminal strip) between the domestic installation and the built-in spotlight connection cable must be clamped in suitable junction boxes. (Not included in the extent of delivery).
7. Close the junction box and push it into the installation opening. Also ensure that the cables are free of compressive and tensile forces. Protect all cables and insulation from any potential damage.
8. Position the built-in light at an angle and first insert a clamp into the installation opening. The springs on the clamp are very powerful and can cause injury if due attention is not paid!
9. Now guide the second clamp into the installation opening. The built-in light is now slowly introduced all the way into the installation opening. The force of the clamps is sufficient to hold the built-in light in position.
10. No further fixings are needed. For precise alignment, the built-in light can be easily repositioned and rotated. The internal part of the light can also be swiveled.
11. Only reinsert the fuse once all built-in lights have been installed.

Removal

1. Pull the built-in light out of the installation opening on one side. Take care to ensure that the clamp does not accidentally slip out of the opening. Otherwise there is a danger that fingers may become trapped.
2. First carefully remove one clamp, then the other, from the installation opening.
3. The further removal process is carried out in the reverse order to the installation process.

Integrating devices into the Hama Smart Home (Solution) APP
The LED built-in spotlight starts to flash quickly (if it does not, switch the LED built-in spotlight ON and OFF again quickly three times in a row).

• Open the app and sign in.
• Press the + in the top right-hand corner to add a new device.
• Choose Lights from the list.
• Next enter your WiFi password and confirm with NEXT.
• Now confirm that the light is flashing quickly by ticking “Next step” and clicking on “Next”.
• The LED built-in spotlight is now connected.
• Once the connection is successful, the product stops flashing quickly and the app confirms that your product is connected. You can now assign it a different name if you wish.
• Click Finish to end the process.
• You can now configure and control the product.

Note
A detailed description of the Hama Smart Home (Solution) App and its full scope of functions can be found in our App Guide at:

www.hama.com  Article Number Downloads App Operating Instructions

Setting options

The following settings can be made in the app:

stored here and selected at the press of a button.
3| Colour slider| Set the preferred colour temperature here.
4| Brightness slider| Set the preferred brightness here.
5| Countdown| Once the set time has elapsed, the light is automatically switched on or off.
6| On/Off button| Switch the light on or off with the press of a button.
7| Timeline| Create time-controlled programmed here.

For extended usage options, scenarios can be created in the app.
(See Section 7 and App Guide)

Extended usage options with scenarios

Scenarios and automated sequences, which can be created in the app in the “Smart scenarios” section, can be used to create many combination and usage options for these  products, depending on the Smart Home products you have installed.
Programming is always via the app (see Section 4 of the App Guide) and will be offered / suggested to you on an individual basis.

Standard usage option

Extended usage option

Care and maintenance

Note
Disconnect the product from the mains before cleaning and during prolonged periods of non-use.

• Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
• Ensure that no water is able to enter the product.

Warranty disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/ mounting, improper use of the product or from  failure to observe the operating instructions and/or safety notes.

Recycling information

Note on environmental protection:
Following the implementation of European
Directives 2012/19/EU and 2006/66/EU into the national legal systems, the following applies:
Electrical and electronic devices as well as batteries must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as  well as batteries to the designated public collection points or to the point of sale at the end of their service lives. Detailed information on this topic is defined in the national  laws of the respective country. This presence of the above symbol on the product, operating instructions or package indicates that the product is subject to these regulations.  By recycling, reusing the materials or other forms of utilising old devices/batteries, you are making an important contribution to protecting our environment.

 RF exposure information

This device complies with the EU requirements for limiting the exposure of the general public to electromagnetic fields by means of health protection. The device complies  with RF specifications provided it is used 20 cm away from the body.

 Declaration of conformity

Hama GmbH & Co KG hereby declares that radio equipment type [00176578, 00176579, 00176588, 00176589, 00176608, 00176609, 00176610, 00176611] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address: www.hama.com -> 00176578, 00176579,  00176588, 00176589, 00176608, 00176609, 00176610, 00176611 -> Downloads.

Technical data

(warm white to cold white)
Lamp current| 45 mA
Frequency band/frequency bands| 2.4 GHz
Maximum radiofrequency power transmitted| < 100 mW

Hama GmbH & Co KG
86652 Monheim / Germany
Service & Support
www.hama.com
+49 9091 502-0 All listed brands are trademarks of the corresponding companies.
Errors and omissions excepted, and subject to technical changes.
Our general terms of delivery and payment are applied.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>