Hunan Wangxing Lamps 2212-4 Pendant Light User Manual

Hunan Wangxing Lamps 2212-4 Pendant Light User Manual

[](https://manuals.plus/wp-content/uploads/2023/02/Hunan-Wangxing-

Lamps-2212-4-Pendant-Light-User-Manual_2.png)WARNING

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.

[](https://manuals.plus/wp-content/uploads/2023/02/Hunan-Wangxing-

Lamps-2212-4-Pendant-Light-User-Manual_2.png)CAUTION

TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.

• INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
• If an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached.
  DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE

INSULATION OF OLDER WIRING.

In regular circumstances the BLACK wire will be the “Hot” lead and the WHITE wire will be the “Neutral” or “Common” lead
A GREEN or BARE COPPER wire is the “Ground”. In older buildings it is always good practice to reconfirm the polarity of the wiring

[](https://manuals.plus/wp-content/uploads/2023/02/Hunan-Wangxing-

Lamps-2212-4-Pendant-Light-User-Manual_2.png)NOTICE

• The important safeguards and instructions outlined on this sheet cannot cover all possible conditions and situations that may occur. it must be understood that common sense, caution and care factors that cannot be built into any product. Caution and care must be supplied by the person(s) installing, operating and caring of this lighting fixture.
• This rectangle box must be securely mounted to the structure of the building. The crossbar and hardware supplied should be used. directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.

PART LIST AND HARDWARE LIST

FIXTURE PREPARATION

1. Remove the fixture.remote and parts bag(s) from the carton.
2. Test the light before installing.
   

NOTICE:

• Before discarding the carton, double check to make certain that all parts are found .

FIXTURE INSTALLATION

1. Make sure the power cut off.
2. Fix the mounting bracket on the ceiling(See Figure-01)
3. Securely connect the power cord.
4. Hanging the rectangle box to the mounting bracket.Make sure to tighten the screws.
5. Push the cable into the small round tube to adjust the light height.
6. Turn on the power switch.

How to connect MASASAT LIGHT with your mobile?

Scan the QR code to get the Mobile APP.
Select English Mode
Download the mobile phone software to control the brightness and color temperature of the lamp

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two con ditions: (1) this device may not cause harmful interference, and (2) this device must accept any i nterference received,including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for Compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable p rotection against harmful interference in a residential installation. This equipment generates use s and can radiate radio frequency energy and, if not installed and used in accordance with the in structions, may cause harmful interference to radio communications. However, there is no guar antee that interference will not occur in a particular installation. If this equipment does cause har mful interference to radio or television reception, which can be determined by turning the equip ment off and on, the user is encouraged to try to correct the interference by one or more of the f ollowing measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help important announcement .

Radiation Exposure Statement

To comply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>