inepro Red Spider RFID Reader User Manual

June 9, 2024
inepro

Red Spider RFID Reader
User Manualette Spider RFID Reader
Technical Manual

Red Spider RFID Reader

Congratulations on your selection of the Nepro Red Spider RFID Reader. We are certain you will be pleased with your purchase of one of the flexible solutions of the market.
We want to help you get the best result from your Red Spider RFID Reader. This manual contains information on how to do that; please read it carefully. Due to continuous product improvements this manual is subject to changes without notice.
We strongly recommend you read the license agreement to fully understand its coverage and your responsibilities of ownership.
Your Nepro dealer is dedicated to your satisfaction and will be pleased to answer your questions and your concerns.
Best wishes, Nepro.
All rights reserved. No parts of this work may be reproduced in any form or by any means – graphic, electronic, or mechanical, including photocopying, recording, taping, or  information storage and retrieval systems – without the written permission of the publisher.
Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the author make no claim to these trademarks.
While every precaution has been taken in the preparation of this document, the publisher and the author assume no responsibility for errors or omissions, or for damages  resulting from the use of information contained in this document or from the use of programs and source code that may accompany it. In no event shall the publisher and  the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused directly or indirectly by this document.
Revision number R 1. This revision of the manual can be applied to products with version 1.0 or higher.

  • Publisher
    Nepro

  • Managing Editor
    K. de Graaff

  • Technical Editors
    K. de Graaff

  • Cover Design
    H. Wagener
    K. de Graaff

  • Team Coordinator
    J. van den Berg

  • Production
    Nepro

Directives

ATTENTION!!
Read this manual carefully before installing the Red Spider RFID Reader!
Guarantee
No guarantee can be given if safety regulations are not followed.
Changes and/or modifications
Changes and/or modifications which have not been approved by the responsible party can void the user’s authority to operate the requirement.
Security
Always disconnect the power supply before handling anything inside the device.

For Indoor Use Only
This device may only be used indoors.
FCC Federal Communications Commission – US
This device is complies with part 15 of the FCC rules, operation is subject to two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
CE  (Conform European Norm)
This device is in conformity with the EMC directive and low-voltage directive.

Confirm Canada Industries
Relevant Devices: Spider
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

RCM Regulatory Compliance Mark
This device is in conformity with Australian law.

End of life directives
Nepro is paying a lot of attention to environmentally-friendly production. Your new device contain materials which can be recycled and reused. At the end of its life  specialized companies can dismantle the discarded device to recycle the reusable materials and to minimize the amount of materials to be disposed of. Please observe the local  regulations regarding the disposal of packaging materials, exhausted batteries and old reequipment.

Introduction

In this manual you find the instructions to install and configure your Red Spider RFID Reader. This manual is meant for all the Nepro Red Spider RFID Reader.
This manual, the Red Spider RFID Reader hardware and software are subject to change, make sure you have the latest version of this manual, because the older versions may have become obsolete.

  Function
The purpose of the Red Spider RFID Reader is to read the unique ID contained in the card that is presented to the reader and transfer this ID to a server. In most cases this  data will be the card serial number. To facilitate this a variety of card reader software modules have been developed. Our configuration tool will enable you to change the  settings on the Red Spider RFID Reader board.
Our reader can read Bluetooth Low Energy, 125KHz and 13,56 MHz Tags.

FCC Certified

**Caution!** Changes or modifications not expressly approved by INEPRO B.V. could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio  frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this  equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense

Requirements

The Red Spider RFID Reader has no known requirements other than a USB host that can read a keyboard-like Human Interface Device

Components

inepro Red Spider RFID Reader - fig

  • P551087 – Red Spider RFID Reader Cardboard box
  • 200020 – Red Spider RFID Reader
  • Red Spider RFID Reader Core Housing Top
  • Red Spider RFID Reader Antenna Board I
  • Red Spider RFID Reader Antenna Board II
  • Red Spider RFID Reader Core Housing Bottom
  • P120647 – External Red Spider RFID Reader Braille RFID Foil
  • Red Spider RFID Reader Serial Stickers | Desktop sticker | EDP Sticker | 2x QR Serial sticker

Check Components
Please check if all the components are in the set before you continue with the installation and set-up.
Some parts may already have been pre-assembled

Software

For the Red Spider RFID Reader there is are tools available each with its specific features. Connect the Red Spider RFID Reader to a computer or laptop and present a card  to the reader. Please note that the reader needs to have the HID RAW Configuration. (See Nepro SCR-MCR-DCR RFID Programmer Tool Full Version manual for more details).

Nepro SCR-MCR-DCR Programmer
With this tool it is possible to change the behavior of the card reader, by creating or editing it’s configuration file. For example it is possible to change the read out of the  RFID card but also the LEDs can be switched off or the volume of the beeper can be changed. Once finished it is possible to store the created settings in a special config file  which can be programmed via the SCR-MCR-DCR RFID Programmer Tool. For more information regarding this SCR-MCR- DCR RFID Programmer Tool please consult  it’s user manual. This tool was developed for the predecessors of the Red Spider RFID Reader. Specific Red Spider RFID Reader tools might be created in a later stage.

** Quick-Test with the Notepad:**

  1. Connect to Nepro Red Spider RFID Reader to the USB PC or laptop.
  2. Start a Text Editor application on Windows, such as Word or Notepad.
  3. Present a card to the Nepro Red Spider RFID Reader.
  4. Remove the card from the Nepro Red Spider RFID Reader.
  5. The data read should be displayed in the Text Editor.

inepro Red Spider RFID Reader - app

This concludes the hardware test

Hardware

Physical test Nepro Red Spider RFID Reader

  1. Connect the Nepro Red Spider RFID Reader to the USB port of a computer.
  2. Check the indicator LED’s to see if the board is operating as it should.

inepro Red Spider RFID Reader - RFID Reader

Blue Led burning:
Reader is powered and has connection
Put a card on the Red Spider RFID Reader:
Besides the blue power LED, the yellow and the green LED should lit. Yellow: card detected
Green: card recognized.
This concludes the hardware test

User Interface

LED’s

On the USB interface board are a number of LED’s. Each of the LED’s has a label, explaining their use. See the table below

Image

| Function| Standby /Normal| Triggered /Not OK
---|---|---|---
| Card is not recognized| Off| On
| Card in detection field| Off| On
| Card Recognized| Off| On
| Reader is on and connected| On| Flashes (no connection)

Technical Specifications

Specifications

Power

Power Supply 5V
Power Consumption DC 5V DC: At maximum (depending on the configuration) 0.5 A

Housing

Material| PCB | PCB/ABS
---|---
Colour| Transparent
Dimensions W x D x H| 37.85 mm x 62.25 mm x 12.5 mm.

CPU

ARM| 32-bit Cortex®-M3 CPU Core | STM32F103
---|---

Memory (working storage)

SRAM 20 KKB

Storage

Falah Memory 64 KKB

Outputs

Pico Blade USB RS232
PID (Product ID) 110
VID (Vendor ID) 1DA6

User Interface

LED’s Red, Yellow/Orange, Green and Blue

Audio

Piezo Buzzer 4kHz, Max. 65 dB

Environmental conditions

EMI / Safety CE, FCC Class A
Operating Temperature (Metric) 0-40 degrees Celsius
Operating Temperature (Non-Metric) 32-104 degrees Fahrenheit
Relative Humidity (Non Condensing) 10%-90%

Troubleshooting
Sometimes things do not work out as expected, if so please read through this section before contacting your service organization or dealer. Changes are you are able to solve the issue yourself.
The section is set up in a Symptom – Prognosis – Resolution format, that is first the symptom is given, then the possible causes and then the resolution for those causes.

Symptom(s): Card not recognized
Prognosis: The Red Spider RFID Reader is not connected
Scope: All Devices
Resolution:

A – Check if the blue light is flashing, if it is the reader is not connected to the server. Please check the availability of the server with another device like a laptop on that network connection.
B – If the blue light burns constantly

  1. Try again
  2. Make sure your card has been linked to your account.
  3. Check if the problem occurs also with other cards, or on other devices.
    C – If the problem has not been solved, please contact your supplier

FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the
user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to  try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
IC STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s)
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying  RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
CAUTION
1. Operation temperature:-20~40ºC
2.The device complies with RF specifications when the device used at 20cm from your body.
Nepro BV hereby declares that this Spider is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU
This information has to be presented in such a way that the user can readily understand it. Typically, this will necessitate translation into every local language (required by  national consumer laws) of the markets where the equipment is intended to be sold. Illustrations, pictograms and using international abbreviations for country names may  help reduce the need for translation.
Max power
BLE:0.5dBm
Tx Frequency: BLE: 2402MHz~2480MHz
NFC: 13.56MHz, 125KHz
Rx Frequency BLE: 2402MHz~2480MHz, 125KHz
NFC: 13.56MHz
BLE and NFC can be used in Europe without restriction.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals