WARRIOR 57384-UPC 10 Amp 7 Inch Variable Speed Polisher/Sander Owner’s Manual

: June 9, 2024
: WARRIOR

Table of Contents

57384-UPC 10 Amp 7 Inch Variable Speed Polisher/Sander
- Owner’s Manual & Safety Instructions
7″ VARIABLE SPEED
Read User Manual Online (PDF format)
Download This Manual (PDF format)

57384-UPC 10 Amp 7 Inch Variable Speed Polisher/Sander

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.

7″ VARIABLE SPEED

POLISHER / SANDER

Polishing Pad and Bonnet sold Separately
Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.

WARNING

Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Copyright© 2022 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

WARNING SYMBOLS AND DEFINITIONS

|

This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.

|

Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.

|

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

|

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

|

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

General Power Tool Safety Warnings

Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.
The term ″power tool″ in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.

For technical questions, please call 1-888-866-5797.

Electrical safety

1. Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with grounded
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.

2. Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.

3. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.

4. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.

5. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock.

6. If operating a power tool in a damp location
is unavoidable, use a Ground Fault Circuit
Interrupter (GFCI) protected supply.
Use of a GFCI reduces the risk of electric shock.

Personal safety

1. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.

2. Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.

3. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energizing power
tools that have the switch on invites accidents.

4. Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.

5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.

7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust‑related hazards.

8. Only use safety equipment that has been
approved by an appropriate standards agency.
Unapproved safety equipment may not provide
adequate protection. Eye protection must
be ANSI‑approved and breathing
protection must be NIOSH‑approved for
the specific hazards in the work area.

For technical questions, please call 1-888-866-5797.

Power tool use and care

1. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.

2. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.

3. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.

5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.

7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.

Safety Warnings Common for Sanding and Polishing Operations

1. This power tool is intended to function
as a sander and polisher. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.

2. Operations such as grinding, wire brushing,
or cutting-off are not recommended to be
performed with this power tool. Operations
for which the power tool was not designed may
create a hazard and cause personal injury.

3. Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool,
it does not assure safe operation.

4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their RATED SPEED can break and fly apart.

5. The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.

6. The arbor size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool. Accessories
with arbor holes that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.

7. Do not use a damaged accessory.
Before each use inspect the accessory such
as abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
After inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute. Damaged accessories will
normally break apart during this test time.

8. Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must
be capable of stopping flying debris generated
by various operations. The eye protection must
be capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtering out particles generated
by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.

9. Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protective
equipment. Fragments of workpiece or of a
broken accessory may fly away and cause
injury beyond immediate area of operation.

10. Hold power tool by insulated gripping surfaces
only, when performing an operation where
the accessory may contact hidden wiring
or its own cord. An accessory contacting a
″live″ wire may make exposed metal parts of
the power tool ″live″ and shock the operator.

11. Position the cord clear of the spinning
accessory.
If you lose control, the cord may be cut or
snagged and your hand or arm may be
pulled into the spinning accessory.

12. Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the surface
and pull the power tool out of your control.

13. Do not run the power tool while carrying
it at your side. Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.

14. Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.

15. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.

16. Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.

17. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

18. Avoid unintentional starting.
Prepare to begin work before turning on the tool.

19. Do not depress the spindle lock when
starting or during operation.

20. Do not leave the tool unattended when it is plugged
into an electrical outlet. Turn off the tool, and
unplug it from its electrical outlet before leaving.

21. Use clamps (not included) or other practical
ways to secure and support the workpiece to
a stable platform. Holding the work by hand
or against your body is unstable and may
lead to loss of control and personal injury.

22. This product is not a toy.
Keep it out of reach of children.

23. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
In addition, people with pacemakers should:

Avoid operating alone.
Do not use with power switch locked on.
Properly maintain and inspect
to avoid electrical shock.
Properly ground power cord. Ground Fault Circuit
Interrupter (GFCI) should also be implemented
– it prevents sustained electrical shock.

24. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.

Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush
or any other accessory. Pinching or snagging
causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power
tool to be forced in the direction opposite of the
accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward
or away from the operator, depending on direction
of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.

1. Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary

handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can control torque reactions or
kickback forces, if proper precautions are taken.

2. Never place your hand near the rotating
accessory. Accessory may kickback over your hand.

3. Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite
to the wheel’s movement at the point of snagging.

4. Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.

5. Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades
create frequent kickback and loss of control.

Safety Warnings Specific for Sanding Operations

Do not use excessively oversized sanding disc paper. Follow manufacturer’s recommendations
when selecting sanding paper. Larger sanding paper extending beyond the sanding pad
presents a laceration hazard and may cause snagging, tearing of the disc or kickback.

Safety Warnings Specific for Polishing Operations

Do not allow any loose portion of the polishing bonnet or its attachment strings
to spin freely. Tuck away or trim any loose attachment strings. Loose and spinning
attachment strings can entangle your fingers or snag on the workpiece.

Vibration Safety

This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders. To
reduce the risk of vibration-related injury:

1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check‑ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.

2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.

3. Wear suitable gloves to reduce the
vibration effects on the user.

4. Use tools with the lowest vibration when there
is a choice between different processes.

5. Include vibration-free periods each day of work.

6. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.

7. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.

SAVE THESE INSTRUCTIONS.

For technical questions, please call 1-888-866-5797.

Grounding

TO PREVENT ELECTRIC SHOCK AND DEATH FROM
INCORRECT GROUNDING WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.

Grounded Tools: Tools with Three Prong Plugs

3-Prong Plug and Outlet

1. Tools marked with “Grounding Required” have
a three wire cord and three prong grounding
plug. The plug must be connected to a properly
grounded outlet. If the tool should electrically
malfunction or break down, grounding provides
a low resistance path to carry electricity away
from the user, reducing the risk of electric
shock. (See 3-Prong Plug and Outlet.)

2. The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire
in the cord must be the only wire connected
to the tool’s grounding system and must
never be attached to an electrically “live”
terminal. (See 3-Prong Plug and Outlet.)

3. The tool must be plugged into an appropriate outlet,
properly installed and grounded in accordance
with all codes and ordinances. The plug and outlet
should look like those in the preceding illustration.
(See 3-Prong Plug and Outlet.)

Double Insulated Tools: Tools with Two Prong Plugs

Outlets for 2-Prong Plug

1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies OSHA
requirements and complies with the applicable
standards of Underwriters Laboratories, Inc.,
the Canadian Standard Association,
and the National Electrical Code.

2. Double insulated tools may be used in either of the
120 volt outlets shown in the preceding illustration.
(See Outlets for 2-Prong Plug.)

Extension Cords

1. Grounded tools require a three wire extension cord.
Double Insulated tools can use either
a two or three wire extension cord.

2. As the distance from the supply outlet increases,
you must use a heavier gauge extension cord.
Using extension cords with inadequately sized wire
causes a serious drop in voltage, resulting in loss of
power and possible tool damage. (See Table A.)

3. The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord. (See Table A.)

4. When using more than one extension cord
to make up the total length, make sure
each cord contains at least the minimum
wire size required. (See Table A.)

5. If you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum cord size. (See Table A.)

6. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
Canada) to indicate it is acceptable for outdoor use.

7. Make sure the extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.

8. Protect the extension cords from sharp objects,
excessive heat, and damp or wet areas.

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOLT)

NAMEPLATE AMPERES

(at full load)

|

EXTENSION CORD

LENGTH

25′

|

50′

|

75′

|

100′

|

150′

0 – 2.0

|

18

|

18

|

18

|

18

|

16

2.1 – 3.4

|

18

|

18

|

18

|

16

|

14

3.5 – 5.0

|

18

|

18

|

16

|

14

|

12

5.1 – 7.0

|

18

|

16

|

14

|

12

|

12

7.1 – 12.0

|

18

|

14

|

12

|

10

|

–

12.1 – 16.0

|

14

|

12

|

10

|

–

|

–

16.1 – 20.0

|

12

|

10

|

–

|

–

|

–

TABLE A* Based on limiting the line volt age drop to five volts at 150% of the rated amperes.

Symbology

|

Double Insulated

---|---

V

|

Volts

~

|

Alternating Current

A

|

Amperes

n0 xxxx/min.

|

No Load Revolutions per Minute (RPM)

|

WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved safety goggles with side shields.

|

Read the manual before set-up and/or use.

---|---

|

WARNING marking concerning Risk of Hearing Loss. Wear hearing protection.

|

WARNING marking concerning Risk of Fire.

Do not cover ventilation ducts.

Keep flammable objects away.

|

WARNING marking concerning Risk of Electric Shock.

Properly connect power cord to appropriate outlet.

Specifications

Electrical Rating

|

120VAC / 60Hz / 10A

---|---

Motor No Load Speed

|

n: 600-3500/min

Max. Accessory Diameter

|

7″ (Ø180 mm)

Spindle Thread

|

5/8″ x 11 TPI / M16

Setup – Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Release the Trigger and unplug the tool from its electrical outlet before
assembling or making any adjustments to the tool.

Installing the Auxiliary Handles

TO PREVENT SERIOUS INJURY:
Do not operate this tool without an Auxiliary Handle properly installed.

The D-Handle (included) may be installed for either right-hand or left-hand use.

Option 1: Using with the D-Handle
Attach the D-Handle to the sides of the Front Cover, using the Hex Key and two Hex Head Bolts.

Note: Slide the Hex Key through the hole in the Handle to access the Bolt on the long side of the Handle.

Option 2: Using with a Side Handle
This tool can be used with many standard angle grinder
side handles which can be installed on either side.

Functions

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Tool Set Up

SANDING DUST FROM SURFACE COATINGS CAN SELF-IGNITE. To prevent serious injury and death from fire, empty bag frequently (at least every 10 minutes) during use and immediately after use. Put dust in a metal can with an airtight lid, and remove dust from premises daily.
Keep a fully charged class ABC fire extinguisher in the vicinity of the work area.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Release the Trigger and unplug the tool from its electrical outlet before installing accessories.

Installing the Backing Pad/Foam Pad

1. The accessory MUST be:
• rated to at least 3500/min.
• no larger than 7″ (Ø180 mm) in diameter.
• fitted with a threaded opening
of 5/8″ x 11 TPI / M16.
• undamaged.
• a backing pad.

2. Press in and hold the Spindle Lock Button
to prevent the Spindle from turning.

3. Thread the Backing Pad onto the Spindle
until firmly secured in place.

Workpiece and Work Area Set Up

Designate a work area that is clean and well‑lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
Route the power cord along a safe route
to reach the work area without creating a
tripping hazard or exposing the power cord to
possible damage. The power cord must
reach the work area with enough extra length
to allow free movement while working.
Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
There must not be hazardous objects, such
as utility lines or foreign objects, nearby that
will present a hazard while working.

Polishing

1. Make sure the surface to polish has been thoroughly
washed, and is free of dust, dirt, oil, grease, etc.
2. Place a clean Foam Pad (sold separately)
securely onto the Backing Pad.
2. Apply about two tablespoons of wax
(not included) evenly on the clean Foam Pad.
CAUTION! Do not apply the wax directly to the surface
of the vehicle. The amount of wax needed will vary
according to the size of the vehicle being waxed.
3. Rotate the Speed Dial to select the
desired speed between 1 and 4.

NOTICE: Only use the slower speeds (1 through 4)
for polishing. Otherwise, damage may occur to
the paint being polished. Harbor Freight Tools is
not responsible for damage to the vehicle’s finish
due to improper use of this Polisher/Sander.
4. Plug the Power Cord into an electrical
extension cord (not included). Then, plug the
extension cord into a grounded,
GFCI‑protected, 120 volt electrical outlet.

WARNING! TO PREVENT SERIOUS
INJURY: To prevent electric shock,
keep cord connection off ground.

Note: Always start and stop the Polisher/Sander
while it is held firmly against the surface of the vehicle.
Failure to do so may result in the Foam Pad or Polishing
Bonnet being thrown from the Polishing Pad.

5. To start, position the unit on the area to be
polished, grip the Polisher/Sander firmly with
both hands and press the Trigger. Release the
Trigger to stop. To use the Lock on button, while
holding in the Trigger, press the Lock On Button,
then release the Trigger. The Polisher/Sander will
stay on. Press and release the Trigger to stop.
6. Keep pressure off of the Polisher/Sander
when operating. The Foam Pad should
LIGHTLY contact the polishing surface.
NOTICE: To prevent damage to the foam pad,
polishing bonnet, and vehicle finish:
Only apply the pad/bonnet flat
against the surface, see below.

7. Begin using the Polisher/Sander to apply wax to the
vehicle. Apply the wax to all flat surfaces with broad,
sweeping strokes in a crisscross pattern. Apply
the wax evenly over the surface of the vehicle.
8. Add additional wax to the Polishing Pad
as needed. To add additional wax:
a. Stop the tool and allow the Polisher/
Sander to come to a complete stop.
b. Add a small amount of wax evenly
over the pad surface.
c. Avoid using too much wax. For additional
applications of wax to Foam Pad, reduce the
amount of wax. The Foam Pad will not absorb
as much wax in subsequent applications.
d. Resume operation.

Note: The most common error when waxing/polishing
a vehicle is applying too much wax. If the Foam
Pad becomes saturated with wax, applying wax will be
more difficult and will take longer. Applying too much
wax may also reduce the life of the Foam Pad. If the
Foam Pad continually comes off the Backing Pad
during use, too much wax may have been applied.
9. After the wax has been applied to the vehicle’s
surface, turn off the Polisher/Sander. Unplug the
Power Cord from the electrical extension cord.
10. Remove the Foam Pad from the Backing Pad and
with your hand and the Foam Pad, apply wax to
any hard to reach areas of the vehicle such as
around lights, door handles, under bumpers, etc.
11. Allow sufficient time for the wax to dry.
12. Replace the Foam Pad and place a clean Polishing
Bonnet (sold separately) securely onto the
Foam Pad.Note: Tightly pull the string to secure
the Polishing Bonnet. Secure the string and
keep it out of the way by tying several knots.
Note: Start and stop the Polisher/Sander only
while it is held firmly against the surface of
the vehicle. Failure to do so may result in the
Bonnet being thrown from the Foam Pad.
13. Start the Polisher/Sander and begin
buffing off the dried wax.
14. When you have removed as much wax
as you can with the Polisher/Sander, turn
off and unplug the Polisher/Sander.
15. Remove the Polishing Bonnet from Foam Pad.
Using the Polishing Bonnet, remove the wax
from all hard to reach areas of the vehicle.

Sanding

1. Make sure that the surface to be sanded is wiped
clean of all dirt and debris, especially that of
previous courser sanding sessions, which will
scratch the surface of a finer grit sanding session.
2. Attach the desired grit Sanding Disk (sold
separately) onto the Backing Pad.
3. Rotate the Speed Dial to select
the desired speed setting.
4. Plug the Power Cord of the Polisher/Sander
into a grounded 120 volt, electrical outlet.
5. To start, grip the Polisher/Sander firmly with
both hands and press the Trigger. Release the
Trigger to stop. To use the Lock on button, while
holding in the Trigger, press the Lock On Button,
then release the Trigger. The Polisher/Sander will
stay on. Press and release the Trigger to stop.
6. Wait until the Polisher/Sander has reached
full speed, then gently contact the surface.
7. Keep heavy pressure off of the Polisher/
Sander when operating. Allow the
sanding disk to do the work.

8. Move the Polisher/Sander in a uniform
pattern up and down or side to side as
you sand to ensure even sanding.
9. Periodically, stop the Polisher/Sander and
check for possible disc wear. Replace used
or worn sanding discs when necessary.
10. When finished, turn off and unplug
the Polisher/Sander.
11. Allow the tool to come to a complete
stop before setting it down.
12. WARNING! SANDING DUST FROM SURFACE
COATINGS CAN SELF-IGNITE. To prevent
serious injury and death from fire, empty bag
frequently (at least every 10 minutes) during use
and immediately after use. Put dust in a metal
can with an airtight lid, and remove dust from
premises daily. Keep a fully charged class ABC
fire extinguisher in the vicinity of the work area.
13. To prevent accidents, turn off the tool and
disconnect its power supply after use. Clean, then
store the tool indoors out of children’s reach.

Maintenance and Servicing

Procedures not specifically explained in this manual must
be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Release the Trigger and unplug the tool from its electrical outlet before
performing any inspection, maintenance, or cleaning procedures.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration occurs,
have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts,
• damaged electrical wiring, and
• any other condition that may
affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
3. Periodically blow dust and grit out of the motor vents
using dry compressed air. Wear ANSI‑approved
safety goggles and NIOSH‑approved
breathing protection while doing this.
4. Periodically recheck all nuts, bolts,
and screws for tightness.
5. Remove Foam Pad from Backing Pad when
Polisher/Sander is not in use. This will allow
Backing Pad to dry and retain its original shape.
Wash with mild soap and water before storing.
6. The Polishing Bonnet may be machine
washed in cold water with mild
detergent. Do not put in the dryer.
7. Use only a clean cloth and mild detergent to clean
the body of the Polisher. Do not use solvents.
Do not immerse any part of the tool in liquid.

8. CARBON BRUSH MAINTENANCE.
The carbon brushes may require maintenance when
the motor performance of the tool decreases or
stops working completely. To maintain the brushes:
a. Remove the Carbon Brush Cover on
each side of the motor housing.
b. Remove the carbon brushes from the
housing. Keep track of which orientation
the old carbon brushes were in to prevent
needless wear if they will be reinstalled.
c. If either carbon brush is worn down by
more than 1/2, replace them both.
d. To clean old carbon brushes before reusing
them, rub the contact areas with a pencil eraser.
e. Reinsert the old carbon brushes in the
same orientation to reduce wear.
f. When installing, make sure the carbon portions
of the brushes contact the motor armature,
and that the springs face away from the motor.
Also, make sure the springs operate freely.
g. Replace the Carbon Brush
Covers. Do not overtighten.
Note: New carbon brushes tend to
spark when first used until they wear and
conform to the motor’s armature.
9. WARNING! TO PREVENT SERIOUS
INJURY: If the supply cord of this power
tool is damaged, it must be replaced only
by a qualified service technician.

Troubleshooting

Problem

|

Possible Causes

|

Likely Solutions

---|---|---

Tool will not start.

|

1. Cord not connected.

2. No power at outlet.

3. Internal damage or wear. (Carbon brushes or switch, for example.)

|

1. Check that cord is plugged in.

2. Check power at outlet. If outlet is
unpowered, turn off tool and check
circuit breaker. If breaker is tripped,
make sure circuit is right capacity for
tool and circuit has no other loads.

3. Have technician service tool.

Tool operates slowly.

|

1. Excess pressure applied to workpiece.

2. Power being reduced by long or small diameter extension cord.

|

1. Decrease pressure, allow tool to do the work.
2. Eliminate use of extension cord.
If an extension cord is needed, use
one with the proper diameter for
its length and load. See Extension
Cords in GROUNDING section.

Performance

decreases over time.

|

Carbon brushes worn or damaged.

|

Have technician service tool.

Excessive noise or rattling.

|

Internal damage or wear.

(Carbon brushes or bearings, for example.)

|

Have technician service tool.

Overheating.

|

1. Forcing tool to work too fast.

2. Blocked motor housing vents.

3. Motor being strained by long or small diameter extension cord.

| 1. Allow tool to work at its own rate.

2. Wear ANSI-approved safety goggles and NIOSH-approved dust mask/
respirator while blowing dust out of
motor using compressed air.

3. Eliminate use of extension cord.
If an extension cord is needed, use
one with the proper diameter for
its length and load. See Extension
Cords in GROUNDING section.

Tool does not sand or polish effectively.

|

1. Disc accessory may be loose on Spindle.

2. Disc accessory may be damaged, worn or wrong type for the material.

3. Wax sprays off polishing pad.

|

1. Be sure disc accessory arbor is correct and Outer Flange/Arbor Nut is tight.

2. Check condition and type of disc accessory. Use only proper type of disc accessory in good condition.

3. Reduce RPM to minimum setting.

Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service.

Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts. Specify UPC 193175478610 when ordering parts.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.