LUM-TEC RPM 1 Durable and Fashionable Watch User Manual
- June 9, 2024
- LUM-TEC
Table of Contents
LUM-TEC RPM 1 Durable and Fashionable Watch
Mission About
Chris Wiegand – President. takes extreme pride in every watch we produce. He
is always available to answer questions and help customers.
We take pride in our service. With service points around the globe, you can be
assured that for any repair you will have a fast turnaround time, so you can
get your watch back on your wrist fast and enjoy it.
LUM-Tee:® takes watch manufacturing and design to a personal level. We freely communicate with our customers through email. phone, and on web forums daily. We value our customer’s opinions and input. We use customer feedback to improve our products and our business. Our customers are what makes LUM-TEc: unique and what separates us from other watch companies.
CARE AND MAINTENANCE
A maintenance interval of between 5 and 10 years is recommended and is in
addition to required battery replacement on quartz models.
Never open the watch yourself. If your watch needs repair or adjustment, take
or mail it directly to a LOM-TEC authorized service repair center.
LOM-TEC assumes responsibility only for service performed at its authorized
service centers.
Shock
All LOM-TEC watches have shock-resistant movements, individually tested to
meet international standards.
Dust
Dust can enter a watch if the case, crystal or crown is not intact. A small particle is enough to stop the movement. Have your watch repaired promptly if the crystal becomes loose, chipped or cracked, or if there is damage to the case or crown.
Magnetism
The exposure of a timepiece to strong magnetic fields will affect its time- keeping and may cause it to stop. A quartz watch should resume working with its original accuracy when removed from the magnetic field . A mechanical timepiece may require demagnetization before it will operate properly again.
Water Resistance
All LOM-TEC watches are tested to meet international standards for water
resistance.
To maintain water resistance , periodic maintenance is required.
The gaskets and crown which seal the case are subject to wear and
deterioration under normal use. These parts should be inspected and replaced
as needed each time the watch is opened for service, including battery
changes.
CAUTION: LUM-TEC will not be responsible for any damage caused by or
related to leakage origination from improper handling or damage to the case,
crown , gaskets or crystal.
IMPORTANT: Do not operate the chronograph pushbutton on a chronograph
model while the time piece is under water.
Basic Instructions
OS20J INSTRUCTIONS
-
A) DATE SETTING :
To adjust the date, pull the crown to position II. Rotate the crown counter clock- wise to the correct date. • If the date is set between the hours of 9:00 PM and 1 :00 AM, the date may not change on the following day. Once finished, push the crown in completely. -
B) TIME SETTING:
Pull the crown out to the Position III. Turn the crown to set hour and minute hands. When the crown is pushed back to the normal position, small second hand begins to run . -
C) CHRONOGRAPH USE
The chronograph can be started and stopped each time button A is pressed . Pressing button B resets the chronograph and the chronograph second hand and chronograph minute hand return to zero position.
Note: If the central hand is not resetting to 12:00 position, pull the crown to position III and press button A to adjust the reset position.
515.24H INSTRUCTIONS
-
Pos. I Position of rest (watch running)
-
Pas. II Quick-change correction for date
The date can also be corrected during the day-changing phase between 10 pm and midnight. The date of the following day has to be set, because no automatic date change takes place at midnight.
– Pull the crown out to position II (watch still running).
– Turn the crown clockwise until the required date appears.
– Push the crown back into position I.
Quick-change correction for 24-hour display
– Pull the crown out to position II (watch still running).
– Turn the crown anticlockwise until the desired time appears.
– Push the crown back into position I. -
Pos. III Setting the time
– Pull the crown out to position III (watch stopped).
– Turn the crown , until the current time is displayed (remember the 24-hour cycle).
– Push the crown back into position I.
R150 & SW200 INSTRUCTIONS
-
Pos. I Manual winding position and normal resting position (watch running)
-
Pos. II Quick-change correction for date
The date can also be corrected during the day-changing phase between 10 pm and midnight. The date of the following day has to be set, because no automatic date change takes place at midnight.
– Pull the crown out to position II (watch still running).
– Turn the crown until the required date appears.
– Push the crown back into position I. -
Pos. III Setting the time
– Pull the crown out to position III (watch stopped).
– Turn the crown , until the current time is displayed (remember the 24-hour cycle).
– Push the crown back into position I.
7004.B INSTRUCTIONS
-
Pos. I Position of rest (watch running)
-
Pas. II Quick-change correction for date
The date can also be changed during the day-changing phase between approx. 8.00 pm and midnight. The date of the following day has to be set, because no automatic date change takes place at midnight.
– Pull the crown out to position II (watch still running).
– Turn the crown until the current date appears.
– Push the crown back into position I. -
Pos. Ill Setting the time
– Pull the crown out to position III (watch stopped).
– Turn the crown , until the current time is displayed (remember the 24-hour cycle).
– Push the crown back into position I.
VS42A INSTRUCTIONS
-
Pos. I Position of rest (watch running)
-
Pas. II Quick-change correction for date (Only used for models with date function)
The date can also be corrected during the day-changing phase between 10 pm and midnight. The date of the following day has to be set, because no automatic date change takes place at midnight.
– Pull the crown out to position II (watch still running).
– Turn the crown clockwise until the required date appears.
– Push the crown back into position I. -
Pos. III Setting the time
– Pull the crown out to position III (watch stopped).
– Turn the crown , until the current time is displayed (remember the 24-hour cycle).
– Push the crown back into position I.
Power depletion warning function
The two-second intervals movement of the second hand is a signal of energy depletion.
The watch continuous running time after two-second intervals movement is 1 day.
CONTACT
WIEGAND CUSTOM WATCH. LLC. 72458 INDUSTRIAL PARK BLVD MENTOR. OH 44060
T. (440)-951-1296
1-877-2LUMTEC
INTERNET
www.Lum-Tec.com
[email protected]
[email protected]
SOCIAL NETWORK
TWITTER – @LUMTECWATCHES
FACEBOOK – FACEBOOK.COM/LUMTECLLC