Godox WMicS2 UHF Compact Wireless Microphone System Instruction Manual

Godox WMicS2 UHF Compact Wireless Microphone System

Forward
Thank you for purchasing!
WMicS2 is a UHF compact wireless microphone system, the evolution and upgradation of S1 system. With the addition of charging case and upgradation of various functions, it provides a satisfying experience for live streaming, interview, video recording, journalistic shooting, audio recording, etc.
Please read this manual carefully before using to make sure the correct operation and exert the optimum function.

Main Features

• 96 wireless channels freely switchable without interference.
• The maximum wireless distance up to 200m.
• UHF Frequency Range: 514MHz-596MHz.
• With OLEO display on transmitter to show the parameters setting.
• Provide output volume control and silent function, support real-time monitoring.
• Built-in chargeable lithium battery.
• Kit 2 includes charging case which provides both charging and
• storage functions.
• Support two transmitters and one receiver to work simultaneously.
• External SD card slot and internal recording function make it a voice recorder individually.
  (Note: as the max. support frequency is 514MHz-596MHz which includes the 96 wireless channel’s frequency, there are parts of frequency may not be utilized.)

Warning

• Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. & Always keep this product dry. Do not use in rain or in damp conditions.
• Keep out of reach of children.
• Do not use the flash unit in the presence of flammable gas. In certain circumstance, please pay attention to the relevant warnings.
• Do not leave or store the product if the ambient temperature reads over 45’C.
• Read and understand all instructions before using.
• Changes made to the specifications or designs may not be reflected in this manual.

Names of Parts

Body-pack Transmitter (WMicS2 TX2)

1. Power Switch/Lowcut Button
2. Record Button
3. Mute/Pair Button
4. Antenna
5. Power Switch/Pair Indicator
6. Record Indicator
7. Lowcut/Mute Indicator
8. Built-in Mic
9. Mic Input Port
10. Type-C Data Transmitting/ Charging Port
11. Reset Hole
12. SD Card Slot
13. 1/4″ Colds hoe Mount Port
14. Charging Points

Portable Receiver (WMicS2 RX2)

1. Power Switch Button
2. Function/Confirm Button
3. A Group Button
4. B Group Button
5. A Group Indicator
6. B Group Indicator
7. Antenna
8. OLED Display
9. 3. 5mm Audio Output Port
10. 3. 5mm Earphone Monitoring Port
11. Type-C Data Transmitting/ Charging Port
12. Reset Hole
13. 1/4″ Colds hoe Mount Port
14. Charging Points

OLED Display

1. Mono/Stereo Mode
2. Receiver Battery Level Indicator
3. A/B Group Frequency Signal  (‘ indicates Disconnection )
4. A/B Transmitter Battery Level Indicator
5. A/B Transmitter Input Volume
6. A/B Group Channel 01-48

UHF Charging Case (WM -C)

1. Pair Button
2. Type -C Charging Port
3. Transmitter Slot 5
4. Receiver Slot
5. Power Indicators

Included Items

Body-pack

Transmitter

| WMicS2TX2| G) x1,@ x1,(J) x1,@ x1, ®x1,@x1,@x1
Portable

Receiver

| WMicS2 RX2| (lix1,@x1,@x1, ®x1, @)x1,@x1,@x1
UHF Charging Case| WM-C| @x1,@x1,@x1, @x1
UHF Compact Wireless Microphone System Kitl| WMicS2 Kit 1| G)x1,(lix1,@x1,@x1,

(J) x1,@ x2, ® x2,@i x1, @x1,@x1,@x1,@x1

UHF Compact Wireless Microphone System Kit2|

WMicS2 Kit 2

| G) x2,(li x1,@ x1,@ x1, @x1,(J) x2,@ x3, ® x3, @)x1,@x1,@x2,@x1, @x1

Operation Instruction

Body-pack Transmitter

1. Power Switch
   Long press the Power Switch/Lowcut Button to power on or off the transmitter. the Power Switch/Pair Indicator will be constant on green after turned on.

2. Lowcut
   Short press the Power Switch/Lowcut Button to turn on lowcut function. the Lowcut/Mute Indicator will be constant on yellow.

3. Recording Backup
   Insert an external TF card into the transmitter, short press the Record Button to enter recording mode, the audio files will be automatically backed up and the Record Indicator will be constant on red. Short press the Record Button again to stop recording, then the Record Indicator will be off. Connect it to the computer with Type-C data cable, short press the Power Switch/Lowcut Button to enter the computer storage mode, user can play back and monitor the recorded audio files.
   Note: The recorded audio files are in WAV format, and there will be one file stored when the recording function is triggered once.
   Recorded files storage rules: The default duration of an audio files is 30 minutes. In case of less than 30 minutes, it will still be stored as one file. If it exceeds 30 minutes, the exceeded part will automatically be stored as another file.

4. Mute
   Short press the Mute/Pair Button to switch to mute mode, the Lowcut/Mute Indicator will be constant on red, the receiver s OLED display shows mute icon, short press it again to exit mute mode.

5. Pair
   Long press the Mute/Pair Button for 3 seconds, the receiver’s OLED display shows “Matching”, then the transmitter starts matching, the Power Switch/Pair Indicator blinks blue and yellow, turns to be constant on green after pair success.

6. Computer-triggered Storage . Short press the Power Switch/Lowcut Button after connecting to the computer with red port of Type-C data cable, the computer will recognize the storage function and eject the U disk.

7. Charging through Type-C port
   When charging through Type-C data cable, the Power Switch/Pair Indicator will be constant on yellow in power on status, while blinks red and then constant on blue after fully charged in power off status.
   Note: The transmitter works normally during charging without affecting the recording backup. USB file reading and writing is not available when recording or synchronizing audio with mobile phone. Connect to the computer through USB port can only charge the transmitter, but the U disk file will not appear in the computer file management until exiting recording or synchronizing audio with mobile phone.

8. indicator Instruction

9. The Power Switch/Pair Indicator will be constant on green when it is powered on but unpaired.

10. The Power Switch/Pair Indicator will blink blue and yellow during pairing, and turn to be constant on green after pairing success.

11. The Record Indicator will be constant on red when recording, and off when stop recording.

12. The Lowcut/Mute Indicator will be constant on red in mute mode.

13. The Lowcut/Mute Indicator will be constant on yellow in lowcut mode.

14. Indicator status when the transmitter battery is lower than 10%:

15. When the pairing is successful/unsuccessful, the Power Switch/Pair Indicator will be constant on red.

16. Record when pairing is successful/unsuccessful, the Power Switch/Pair Indicator and the Record Indicator will be constant on red.

17. Record and turn on the lowcut function when the pairing is successful/unsuccessful, the Power Switch/Pair Indicator and the Record Indicator will be constant on red, and the Lowcut/Mute Indicator will be constant on yellow.

18. Record and mute when pairing is successful/unsuccessful, the Power Switch/Pair Indicator, Record Indicator and
    Lowcut/Mute Indicator will be constant on red.

19. Indicator status when plugging in the power adapter:

20. The Power Switch/Pair Indicator will be constant on yellow when charging in power on status, while blinks red when charging in power off status, and turn off after fully charged.

21. Record in power on status, the Power Switch/Pair Indicator will be constant on yellow, and the Record Indicator will be constant on red.

22. Record and turn on the lowcut function in power on status, the Power Switch/Pair Indicator will be constant on yellow, the Record Indicator will be constant on red, and the Lowcut/Mute Indicator will be constant on yellow.

23. Record and mute in power on status, the Power Switch/Pair Indicator will be constant on yellow, the Record Indicator and Lowcut/Mute Indicator will be constant on red.

Portable Receiver (WMicS2 RX2)

1. Power Switch
   Long press the Power Swatch Button for 2 seconds to power on/off, the OLED display will chiton.

2. Language Setting
   The receiver will automatically enter the language setting interface when turned on for the first time, short press the A/B Group Button to enter language selection, short press the Function/Confirm Button to confirm the language, it will automatically show the saved language afterwards. Press and hold the A/B Group Button for 4 seconds at the same time to automatically reset and clear the original data, then it will automatically enter the language setting interface after restarting.

3. Pairing
   Long press the A/B Group Mono Button for 2 seconds, the A/B icon blinks in dashed box on the OLED display, it will  recognize transmitters and start pairing with “pairing” (group A 1s paired and group B 1s unpaired) appears on the display. If the Pairing is successful, “Pairing ok” appears on the display and returns to the main interface, then the A/B Group Indicator be constant on green, A/B Transmitter Battery Level Indicator displays the real-time battery level, channel No. displays under the  icon, A/B Group A/B Group icon turns into solid box, A/B Transmitter Input Volume icon displays real-time volume. If the Pairing is unsuccessful, “Pairing fail” appears on the display and returns to the main interface.

4. Channel Setting
   Short press the A/B Group Button, the display shows the A/B group channel No. (01-48), long press the A/B Group Button to make the adjusted channel No. blinks, then short press the A Group Button can decrease channel No., while short press the B Group Button can increase channel No., finally short press the Function/Confirm Button to confirm the channel setting.

5. Volume Setting
   Short press the A/B Group Button, the display shows the volume No. of A/B group (01-10), long press the A/B Group Button to make the adjusted No. blinks, then short press the A Group Button can decrease the volume. while short press the B Group Button can increase the volume. finally short press the Function/Confirm Button to confirm the volume setting.

6. 0utput Mode Setting Short press the A/B Group Button, the display shows the output mode (Mono/Ste­reo). long press the Function/Confirm Button to make the yellow icon blinks, then short press the A/B Group Button to switch between mono and stereo mode, finally short press the Function/Confirm Button to confirm the output mode setting. Short press the A/B Group Button at the same time on the main interface can also switch between mono and stereo mode.

7. 0LED Light Setting
   Short press the A/B Group Button, the display shows the OLED light (1-8). long press the Function/Confirm Button to make the number blinks. then short press the A Group Button can decrease the light, short press the B Group Button can increase the light, finally short press the Function/Confirm Button to confirm the light setting.

8. Screen Dormancy
   Short press the A/B Group Button, the display shows the screen dormancy time (10S/30S/60S). long press the Function/­Confirm Button to make the number blinks. then short press the A Group Button can decrease the screen dormancy time, short press the B Group Button can increase the screen dormancy time, finally short press the Function/Confirm Button to confirm the screen dormancy setting.

9. Screen Rotate
   Long press the Function/Confirm Button can rotate the screen.

10. indicator Instruction
    The OLED display will light on after powered on. If the A/B group is paired successfully, the corresponding indicator will be constant on green, and turn off after disconnected.

UHF Charging Case (WM-C)

1. Pair Button
   The transmitter/receiver will enter deep sleep after fully charged for one day, and cannot be turned on when you pick it up, it needs to be put into the charging case and press the Pair Button to wake up. Long press the Pair Button for 3 seconds, the transmitter/receiver will automatically start pairing.

2. Power Indicators (4)
   Self-charging: the Power Indicators will blink green increasingly, and all be constant on green after fully charged. Charging the transmitter/receiver: the Power Indicators will be constant on green when charging the transmitter/receiver, decreasing along with its battery level.

Installation Instruction

Transmitter

1. Insert the omnidirectional lava lier microphone into the transmitter’s  MIC port
2. Turn on the transmitter to set the relevant parameters.
3. Clip the transmitter onto the belt, collar, sleeve or put it into your pocket.
   Note: When clipping the transmitter on the collar with magnetic collar button, you can speak directly at the built-in mic without using the omnidirectional lavalier microphone.

Receiver

1. Connect the 1/4″ cold shoe onto the receiver, and install them on the camera or shooting equipment.
2. Insert one end of the 3.5mm cable into the receiver’s OUTPUT port and the other end into camera’s MIC port.
3. Turn on the transmitter to set the relevant parameters.
   Note: Please set the group and channels of transmitter and receiver to the same when setting parameters. When a receiver is connecting to two transmitters, A transmitter must be set and used in A group while B transmitter must be set and used in B group.

Technical Data

Group B 48)

| 96(Group A: 48;

Group B: 48)

|
RF Frequency
Range| 514MHz-596MHz| 514MHz-596MHz|
Audio Frequency
Range| 40Hz-18KHz| 40Hz-18KHz|
Sound Delay| 12ms| 12ms|
Audio Input Port| 3.5mm| 3.5mm|
Lithium Battery
Capacity| 770mAh| 770mAh| 10000mAh
Type-CInput
Parameters| 5V/0.4A| 5V/0.4A| 5V/2A(Max)
Working Temperature

Range

| -10°C~45°C| -10°C~45°C| -10°C~45°C
---|---|---|---
Receiving Distance| Barrier-free receiving distance: 200m, Barriered receiving

distance: 60m

| Barrier-free receiving distance: 200m, Barriered receiving

distance: 60m

|
Signal Noise

Ratio

| •70d8| •70dB|
Receive

Sensitivity

| | -95dBm|
Distortion| | Below 3%|
Dimension| 65.8X50.4X20.5mm

(Antenna length 65mm)

| 65 8X58.4X20.5mm

(Antenna length: 65mm)

| 185.8X84.2

x42mm

Net Weight| 57g| 669| 367g

Troubleshooting

• Unable to receive audio signal. Make sure batteries are installed correctly and Power Switch is turned on. Check if the transmitter and the receiver are set to the same channel, if the microphone or earphone is well connected, or if the devices are set to the correct mode.
• Check if the transmitter is set to mute mode or not.
• Signal disturbance or shooting interference. Change a different channel of the transmitter and receiver.
• Operating audio distance limited or signal missing. Check if batteries are exhausted. If so, replace them.

Maintenance

• Avoid sudden drops. The device may fail to work after strong shocks, impacts, or excess stress.
• Keep dry. The product isn’t water-proof. Malfunction, rust, and corrosion may occur and go beyond repair if soaked in water or exposed to high humidity.
• Avoid sudden temperature changes. Condensation happens if sudden temperature changes such as the circumstance when taking the transmitter and receiver out of a building with higher temperature to outside in winter. Please put the transmitter and receiver in a handbag or plastic bag beforehand.
• Keep away from strong magnetic field. The strong static or magnetic field produced by devices such as radio transmitters leads to malfunction.
• Unauthorized service will void the warranty.
• If the product had failures or was wetted, do not use it until it is repaired by professionals.
• Changes made to the specifications or designs may not be reflected in this manual.

FCC Caution

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
   Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement.

The device can be used in portable exposure condition without restriction.

Warning
Operating frequency:514MHz-596MHz
Maximum ERP Power: 5dBm

Declaration of Conformity

GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states.For more information of DoC, Please click this web link:
https://www.godox.com/DOC/Godox_WM icS2_Series_DOC.pdf.
The device complies with RF specifications when the device used at 0mm from your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>