Husqvarna VIKING Bottle Bag with Candlewicking Stitches Instruction Manual
- June 9, 2024
- Husqvarna
Table of Contents
Husqvarna VIKING Bottle Bag with Candlewicking Stitches
Sewing Supplies
- HUSQVARNA® VIKING® Sewing Machine
- 2/3 yd. (55 cm) Thai silk fabric in red or green (fabric width at least 39 3/8” (1 m)
- Tear Away stabilizer
- 28” (70 cm) ribbon
- Sewing thread
- Rayon Embroidery thread
Optional accessories
- Candle wicking Foot (413162345)
- Seam ripper
- Swarovski Crystals
- Decorative Touch Applicator
- Clear 2-3 mm Embellishment Foot (413030445)
3/8” (1 cm) seam allowance included in measurements.
Cut
Cut a side piece 10 5/8” x 17” (27 x 43 cm), a circle 3.5” (9 cm) in diameter
for bottom and a 2” (5 cm) wide and 39 3/8” (1 m) long strip for handle.
Mark vertical lines with ¾” (2 cm) space, in various lengths from 5.5”- 10
5/8” (14 – 27 cm) on the side piece. (The first and last line 1 ¼” (3 cm) from
the sides because of the seam allowance.)
Sew
Thread with embroidery thread on top and sewing thread in the bobbin. Snap on
the Candle wicking Foot that is available as an extra accessory. (Read about
the foot in the Accessory User’s Guide). You can use other decorative stitches
on your sewing ma-chine if you don’t have a Candle wicking Foot.) Place tear
away stabilizer underneath the fabric and sew candle wicking stitches or other
decorative stitches in green and red along the marked lines (Illustration A).
Tear away the stabilizer.
Turn under ¼” (6 mm) along the sides of the 39 3/8” (1 m) long strip. Fold double lengthwise. Press. Snap on presser foot D or the optional Edge Joining Foot. Select straight stitch and adjust needle position to the left. Topstitch the sides.
Pin the handle 3” – 3 ¼” (7.5 – 8 cm) from the side edges on the side piece. Select a decorative stitch and stitch in place from the bottom and 10” (25 cm) up (Illustration B).
Rethread with sewing thread on top and in the bobbin. Select zig zag. Snap on presser foot B and overcast the edges all around the piece. Select straight stitch and snap on presser foot A. Fold the piece right sides together. Sew the side seam. Press seam allowance flat open. Divide and mark the bot-tom piece and the side piece in four. Pin and sew the bottom piece right sides together with the tube matching marks. Turn the bottle bag right side out.
Fold under the upper edge 4” (10 cm) to the wrong side. Press. Sew 6
buttonholes 2” (5 cm) from the upper folded edge with 2” (5 cm) space. The
first and last buttonhole 1” (2.5 cm) from the side. Use the Sensor Buttonhole
Foot for even buttonholes in the same size. (Illustration C).
Use a seam ripper to cut up the buttonholes. Thread the ribbon through the
buttonholes to tie up the bottle bag.
Tips and hints: The bottle bags looks extra luxurious and decorative with
beautiful Swarovski crystals.
Use the Decorative Touch Applicator especially made for easy application onto
the fabric. Another tip is to use the new Clear 2-3 mm Embellishment Foot.
This foot helps you to sew an entire row of small pearls onto the fabric in no
time!
VSM Group AB • SE-561 84 Huskvarna, Sweden • www.husqvarnaviking.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>